高层建筑外墙清洗机(升降机部分)的设计含10张CAD图
高层建筑外墙清洗机(升降机部分)的设计含10张CAD图,高层建筑,外墙,清洗,升降机,部分,部份,设计,10,cad
高层建筑外墙清洗机(升降机部分)的设计含10张CAD图需要咨询购买全套设计请加QQ1459919609-图纸预览详情如下:升降机部分总装图.dwg卷筒.dwg吊钩.dwg底座.dwg文件清单.txt杆臂.dwg杆臂支座.dwg清洗机部分.dwg滚轮.dwg电路图.dwg短轴.dwg设计副本设计封面.doc零件图汇总.dwg高层建筑外墙清洗机(升降机部分)的设计任务书.doc高层建筑外墙清洗机(升降机部分)的设计说明书.docx高层建筑外墙清洗机(升降机部分)的设计Design of Exterior Wall Cleaning Machine (Lift Part)of High - rise Building摘 要社会在不断发展,人类在断进步,以及生活水平的不断提高,城市建设也更加规范,整洁。现如今城市高楼林立,高层建筑为了达到美观,所用的外墙的装饰材料种类也越发繁多,如玻璃,瓷砖,或特殊涂料 。 , , , 以及 , 会 建筑 外墙 到不 的 , , ,不如currency1“整洁美观,建筑 外墙 城市fi的fl部分, 人 的,要”整洁,如 以及 , 需要 进 清洗,整以及 。为fl种 ,本, 全的高层建筑外墙清洗机, 高, , 本, 。 机 分为 部分,fl部分为 部分, 在所清洗的高层建筑 ,fl部分为进 高层建筑外墙清洗的清洗机部分。在建筑外墙进 清洗 , 升降机部分 在所清洗墙面的 ,升降部分进 支 杆臂清洗机部分进 整, 部分的 电机进 高 , 清洗部分 提升,达到要清洗的 , 电机 进 的 ,机 支 杆臂 轮,钢丝绳牵引,以 下移 ,清洗机供水系统 ,清洗机机 部的喷水嘴喷。清洗机部分在整体结构 采用框进 组装有三套清洗刷具组在框 分别有三根导轨每根齿条导轨有fl套刷具并且每套刷具独立进 清洗 的移 在电 机的 下 减装 链轮 给刷具 之进 墙面的清洗以及 整套刷具在到导轨进 移 。在三套刷具的共 下以有 防止漏刷清洗不不全面 失误 墙壁达到整洁。关键词:高层建筑外墙清洗机”清洗机升降机”清洗机AbstractSociety in the continuous development of human progress in progress, and the continuous improvement of living standards, urban construction is more standardized and clean. Now the city tall buildings, high-rise buildings in order to achieve aesthetics, the use of the external walls of the decorative materials are also more and more numerous, such as glass, tiles, or special coatings and so on. However, the weather often changes, wind and frost snow, solar radiation and haze pollution, dust weather will make the building walls suffered different degrees of pollution damage, become worn, or even broken, no longer as clean and beautiful as the original, The facade of the building is part of the image of the city, and he is like a persons clothes, to keep clean,clean, if contaminated and damaged, we need to carry out his cleaning, finishing, and routine maintenance.As a small investment, low cost, safe and reliable work of high-rise building exterior cleaning machine, its work efficiency is high, the environmental pollution is small, cost savings, saving resources. The machine is divided into two parts, part of the power part, placed in the cleaning of the high-rise building roof, and the other part of the high-rise building exterior cleaning machine parts. Before the cleaning of the building exterior, the lift part is placed in the relative roof position of the cleaned wall, and the lifting part is fixed. Then, the position of the cleaning machine is adjusted by the support rod arm, and the two-speed motor High-speed transmission power, so that the rapid increase in the cleaning part to reach the relative position to be cleaned, two-speed motor began to reverse the power output, the rack along the support arm through the pulley, through the wire rope to start at the working speed began to move down , The washing machine water supply system at the same time began to work, along the top of the washing machine rack spray nozzle. The cleaning machine is part of the overall structure of the frame using the assembly, there are three sets of cleaning brush, in the frame, respectively, there are three rails, each rack rails have a set of brush, and each set of brush can be cleaned independently Move the motor under the power output, through the reduction device, the power transmission through the sprocket to thebrush, so that the wall cleaning, and make the whole set of brush in the rail tomove, in order to achieve the brush for repeated cleaning , The limit switch is mounted on both ends of the guide rail so that it can be moved in the reverse direction each time the brush movement touches the limit switch. And in the three sets of brush under the common work, can effectively prevent the leakage brush, cleaning is not clean, not comprehensive and other work errors, so that the walls to clean and tidy.Key wordsHigh-rise building exterior cleaning machine, washing machine lift, washing machine目 录1 言11.1 清洗建筑表面的意义 11.2 高层建筑外墙清洗方法介绍 11.3 高层外墙清洗机简介 42 整机的 原和主要参数 52.1 原 52.2 清洗设备的主要参数 63 高层建筑外墙清洗机升降机部分的设计73.1 电机的选用 73.2 减 的设计与选用 83.3 钢丝绳的设计与选用 83.4 卷筒的设计与计算 93.5 轮的设计与选用 113.6 吊钩的设计与选用 133.7 联轴 的选用 143.8 制 的选用 153.9 杆臂的设计及强 校核 153.10 支 杆的设计 173.11 脚轮的选用 183.12 缓冲 的设计与选用 184 高层建筑外墙清洗机清洗机部分的设计194.1 原 194.2 独立刷具的电 机的选用 204.3 链 的设计 204.4 齿轮齿条 设计 214.5 按齿根的弯曲疲劳进 设计 234.6 齿轮轴及装备的轴承设计校核计算 254.7 控制电路的设计 29总 结31致 谢32参考文献33
收藏