许疃煤矿3.0Mta新井设计含5张CAD图.zip
许疃煤矿3.0Mta新井设计含5张CAD图.zip,煤矿,3.0,Mta,设计,CAD
英文原文The dynamic impact of rock burst induced by the fracture ofthe thick and hard key stratumFENG Xiaojun,WANG Enyuan,SHEN RongxiState Key Laboratory of Coal Resources and Safe Mining, China University of Mining and Technology, Xuzhou 221008, ChinaAbstract:To reveal the dynamic impact of rock bursting induced by the thick and hard roof of gravel as key stratum fractured,based on the key strata and rock control theories,combined with the mechanical load-based dynamic loading with the Law of Conservation of Energy in a system,this paper analysed the static stability and the processing of energy conversion within the system when the key stratum was fracturing.And the key stratum dynamic model of fracturing was established.The results indicate that large amounts of strain energy would be forced into the rock during the process as the key stratum fractures and becomes unstable.The greater the dynamic load factor is,the more elastic energy is forced into the lower rock strata of the key stratum,and the more obvious the dynamic impact of the lower rock strata would be.The size of the dynamic load factor relates to the aspect ratio of key rock masses,the thickness of the overburden,the mining height,the height of the fragmentized rock at the bottom of key stratum and the compaction coefficient of the fragmentized rock under the static during loading conditions.According to the calculation of actual work,the results are consistent with the field tests approximately.The results can provide references to similar conditions.Keywords:key stratum;rock burst;dynamic loading;energy constant1.IntroductionThe key stratum controls the overlying rock strata,even to the surface,with high strength,high thickness,and overall subsidence of overlying strata happen easily when it fractures1-3.The key stratum that has different lithology,strength and thickness impacts the control of the rock strata and the dynamic impact of rock burst after it fractures4-7.As the key stratum,the thick and hard roof with gravel is controlling the movements of the entire overburden,because of its characteristics of high strength,high thickness,fracture would not happen until the area of mining space reaches a value that is big enough8.The whole overburden even surface sinks the surface instantaneously when it fractures, causing a release of strong dynamic force on the rock strata below the key stratum.With the increasing in the strength and depth of mining exploitation,the dynamic impact of rock burst will be more and more important when the key stratum fractures suddenly,and the support designs and the hazards of rock burst induced by dynamic effects continue to increase9-10.The previous have developed comprehensive and systematic studies on rock control,mining damage and the mechanism of water inrush at the overburden separation area11-14.Reference15discussed the impact on the height of water inrush caused by the location of key stratum,and explained the mechanism of water inrush in some coalmines accidents.Reference16discussed the stress of the compound key stratum with the Elastic Thin Plate Theory and Laminated Plate Theory of the mechanics of composite materials,and obtained the limit load when the key stratum was unstable by using plastic limit analysis methods,regarding the combined motion of rock strata overburden as the combined motion of the key strata based on the hard rock strata.Reference17discussed the mechanical mechanism that it could easily cause mining earthquake and rock burst occurrence when the key stratum broke off in positiveO-Xtype,and by monitoring the rock burst induced by the fracture of the key stratum instantly in three-dimensions using the micro seism monitoring system.As the key stratum fracture is a dynamic loading process to the lower rock strata,causing the loading process of rock fracturing is different from the general static loading conditions,it is necessary to conduct researches on the rock burst induced by the fracture of the key stratum.This paper established the dynamic model of the key stratum fractured and derived the dynamic load factor when the dynamic impact loading on the lower strata by combining the theory of the mechanical load-based dynamic loading with the law of conservation of energy of system, we analysed the static stability and the process of energy conversion within the system when the key stratum was fracturing.Confirmatory calculation of actual work was also done,which was consistent with the field tests approximately.The results can provide references to similar conditions.2.Subsidence profile curve of the super mining explorationThe super mining exploration is the critical mining state that the width of goaf is larger than 1.2 to 1.4 times the depth.Compared with the full exploration,the maximum subsidence in the central of the super mining exploration shows:the distribution of the maximum subsidence presents regional characteristic. The fracture interval is closely related to rock mass strength and thickness according to the theory of the model of main roof initial fracture.The greater the intensity and thickness are,the greater the fracture interval is,so the mining conditions are determined by the rock property and thickness of the key stratum. As the thick and hard layer of gravel of the key stratum possesses high strength,high integrity,and it is not easy to fracture,the fracture interval is far greater than the general strength of the key stratum, on which conditions,the movements of rock below the key stratum can be regarded as the super mining exploration.According to the super mining exploration theory,the deformation of the surface subsidence varies from zero to maximum with time,which is similar to the full mining exploration.To facilitate the description of the subsidence profile curve of the mining exploration,the subsidence profile curve of the super mining exploration is divided into three parts“full explorationequal deformationfull exploration”,which is shown in figure 1.The super mining exploration curve equation was described by the sink basin profile function derived by Soviet Unions18.(1)Where Vz is the value of separation area height below the key stratum,Vzm is the maximum value of separation area height below the key stratum,x is the horizontal distance from the centre of the separation area to the expected point of surface subsidence,L is the distance from the centre of the separation area to the boundary of the sink area.Fig.1 The key stratum mining model of the thick and hard layer3.The dynamic impact model of key stratumThe dynamic loading effects are caused to the lower rock strata when the key stratum fractures.The instantaneous stress level is much higher than the static in the stable state,and it forces large strain energy into the rock strata in the form of elastic wave in a short period of time,being superimposed with the original energy.When the key stratum fractures,the more elastic energy is forced into the lower layer of the key stratum,the greater the scope the greater the energy,and the more obvious the dynamic effects to the lower strata.So it can be seen that the greater the dynamic load factor,the higher the stress level,the greater the inputted energy,the more prone to instability for rock.Based on the state of the super mining exploration in the plane model,combined with mechanical mechanism and equilibrium conditions of the main roofbond-beamstructure,it is confirmed that when the lower strata are shocked by the fractureof the key stratum,lots of energy is forced into the lower strata at the earlier stage through the two salient points where they are contact with.With the variation of coefficients,the contact extent increases constantly,and extends to surface gradually.Given that the stress disturbance and the energy release on the fracturing moment make the greatest effects on the surrounding rock masses,we focused on studying the state on the fracturing moment.Based on the above analysis,the key stratum mechanical model on the plane of the thick and hard layer was established.See figure 2.Fig.2 The thick and hard layer of the key stratum model for dynamic impactAccording to the actual engineering conditions,combined with the theory of the key stratum fracture, assuming the key stratum of thick and hard layer as like rigid body,i.e.the effects on the dynamic impact process from the deformation of fracture can be by passed.Considering the variation of the cushion coefficient,the dynamic impacted rock subject to Hookes Law and the elastic modulus is not changed. The key stratum fractures instantly when the mining interval reaches the limit value.The energy releases by fracturing is composed of three parts:within the survey region,external load exerts on the key stratum through the upper boundary of it,which will produce a certain displacement under the action of force.i.e. the energy generated by external load;then the key stratum will produce a displacement downward when it fractures,the change of gravitational potential energy;finally,the kinetic energy of the key stratum before the key stratum fractures.The energy equation was established by the theory of conservation of energy.(2)Where W is the energy generated by external load,T is the kinetic energy before the key stratum fractures,V is the gravitational potential energy,Vd is the energy increase in the rock strata below the key stratum.3.1 Solve the dynamic load factorThe stress and displacement on the moment of the key stratum fracturing is far greater than that in the state of stationary.It is difficult to measure the stress and displacement directly under the actual engineering conditions or by using theoretical arithmetic,while it is easy under the static conditions.The dynamic load factor is defined as ratio of dynamic load stress,displacement and the static stress, displacement.The simultaneous equations that are used to resolve the dynamic load factor are established by combining the static mechanical analysis with the energy constant laws.The concrete steps are as follows.3.1.1 Solve the static mechanical equationThe model shown in figure 2 is analysed with the static mechanical theory,setting up the following equations based on the material mechanical analysis.(3)(4)The static stress is solved based on the above equations,the result is as follow:(5)Where a and b are the length and height of the block mass of the key stratum,?is the maximum angle when the key stratum fractured,?is the depression angle of the block mass of the key stratum,i.e. the arctan a/b shown in figure 2,G is the gravity of the two block masses,Fy is the vertical stress of the boundary of the key block masses below the key stratum,Fst is the static on the static equilibrium conditions, st is the displacement on the static equilibrium conditions.3.1.2 Energy SolutionUnder the action of the static,with the effects of the cushion coefficient,the lower strata occur to some subsidence;and in the process of rock bursting,not only does the static impact the subsidence,but also the displacement subsidence is also impacted by dynamic loading.Taking into account the range of the lower impacted strata is large,and the strata are fragmentized on the whole and fully cracks,it is considered that it is mainly the mutual embedding of the rock fractures in the process of impact,and the real kinetic energy of the impacted strata are small which is seen as zero in the following equations.The formulas follow:(6)(7)(8)Where Fd is the dynamic loading of rock induced by the key stratum fractured,d is the dynamic displacement of rock induced by the key stratum fractured,h is the mining height,ha is the thickness of roof collapse above the coal seam,K is the dynamic load factor,is the compaction factor under static load,usually between 0.05-0.15.The characteristics of the fracturing process and movements are assayed.Beside the energy from the upper loading,there only exists the transformation of the gravitational energy in the model.The W and V are figured out based on the theory of quality differential.(9)(10)Where y is vertical displacement of the key block mass.3.1.3 Solve the dynamic load factorThe simultaneous equations are solved by using the static stress in formula 5 and the energy generated by external load in formula 9 and the potential energy changes in formula 10.(11)Result of the dynamic load factor(12)The dynamic load factor is resolved according to the above formulas.Adding the relationship between the dynamic load stress,displacement and the static stress,displacement,the dynamic load stress and displacement of the impact from the key stratum to the lower layer could be worked out.Combining with the safety factor,the possible maximum stress and displacement after the key stratum fractures can be developed,which may provide references for support designing and safety mining in the next phase.3.1.4 Analysis of resultsThe analysis of dynamic load factor formula shows that the size of the factor is relate with several parameters including the aspect ratio of the key block masses,the thickness of the overburden,the mining height,the thickness of the bottom of the key stratum and the compaction coefficient on static loading conditions.Because the contribution from each parameter is different,the sensitivity of different parameters from the dynamic load factor is different as well.In order to study the sensitivity of different parameters,the formulas are analysed by using the principle of single-factor changing.On the given actual conditions,this paper focused on the sensitive analysis of the static load compaction factor and the vertical overburden pressure so that it could be applied as much as possible to the similar mining areas.The results are shown as follows:Fig.3 The dynamic load factor changes with different cushion coefficientsFig.4 The dynamic load factor changes with different burial depthFigure 3 shows that the dynamic load factor increased with the decrease of cushion coefficients under the actual mining geology conditions,which suggests that the lower strata collapse are equivalent to the formation of a loose buffer space,making the effect of rock burst is relatively little when the key stratum fractures.On the other hand,it explains that it favour the management principle of the mining pressure when the roof suddenly fractures by increasing the fragmentation of the main roof.Figure 4 shows that the dynamic load factor increases with the burial depth decreasing.The main reasons are:as the depth increased,the incremental value of static stress itself is at a very high magnitude.Although the dynamic load factor trends downward around-0.2 with the depth increasing,it does not mean that the dynamic effect decreased.Although the dynamic load factor is relatively smaller,the static load by each part of the dynamic load factor increased greatly.The increase of static stress makes a major contribution to the dynamic impact of rock burst at this time.That is to say although the relative dynamic load decreases,the absolute static increases greatly,so the management and monitoring should be strengthened to prevent rock burst hazards.4.Checking the actual projectA coal mine located in north-eastern China.In the process of deep mining,the mine ground pressure tended to intense,and rock burst occurred many times.The main coal seams are 3#and 9#at present.The hardness of 3#coal is greater(Plats coefficient f=3).The average coal thickness is 3.38meters,and the average depth is-400 meters or so.The average coal seam angle is 30-33.The immediate roof is fine sandstone of 3 to 15meters,which has a 9 meters sandstone thickness.The thickness of the main roof is around 60 meters gravel,which is determined as the key stratum by calculating and analysing.The mining pressure reports show that the main roof?s first weighting interval is around 100 meters under the conditions,so parameteracan be determined to be 50 meters.After the field test on the force of the support when the main roof fractured firstly,it was found that the dynamic pressure coefficient was about 2.2.The following parameters are determined after calculation.The results are shown in table 1.Table.1 The actual project results by using the formula 12ParametersabK2KThe actual dynamic pressure coefficientValue506060.16.722.592.1-2.4The results showed that the theoretical result of the dynamic load factor based on the formula is larger than the measured one.Analysis shows the following reasons:on the one hand,the calculation is completed within the elastic deformation,but the rock plastic deformation would also happen due to the presence of high stress under the actual situations,even though the gravel roofs are hard,thick and strong enough,the joints are still exist in them.The relative motion of joints and the friction would consume energy constantly,which lead to larger calculation result;on the other hand,the energy is inputted to both sides of the key stratum in the form of elastic wave and the energy transfers effectively,which is both ignored in the process of energy calculation,which causes the energy value is larger than the actual result, leading to the K value larger,but some guidance and practice still could be given to engineering references.5.Conclusions1)Under the exploration conditions that the thick and hard roof of gravel is regarded as the key stratum, the separation area matches the subsidence profile curve of the super mining exploration,having the equal deformation at the central region.The model which contacts the lower strata with two salient points when the thick and hard layer of the key stratum fractured is established.Lots of energy is forced into the lower strata at the earlier stage through which they contacted firstly.2)A large amount of strain energy would be forced into the rock during the process of fracture and destabilization of the key stratum.The greater the dynamic load factor was,the more elastic energy that is forced into the lower strata,and the more obvious the dynamic impact on the lower rock strata would be, the more easily it lead to rock burst hazards.3)The size of the dynamic load factor relates to the aspect ratio of key rock masses,the thickness of the overburden,the mining height,the thickness of the rock broken down at the bottom of key stratum and the compaction coefficient on static during loading conditions.The dynamic load factor increases with the cushion coefficients decreasing.The lower strata collapse are equivalent to the formation of a loose buffer space,making the effects of rock shock are relatively little when the key stratum fractured;the dynamic load factor increases with the burial depth decreasing.Increment of the static stress becomes a major contribution to the dynamic impact on rock burst at this time.According to the calculation of actual work, the results are consistent with the field tests.6.References1Qian M G,Miao X X,XU J L,Mao X B.Key strata theory in ground control.Xuzhou:China University of Mining and Technology Press,2003:17-18.(In Chinese)2Qian M G,Miao X X,Xu J L.Study of key stratum theory for control.Journal of China Coal society,1996,21(3):225-229(In Chinese).3Xu J L,Zhu W B,Wang X Z,Yi M S.Classification of key strata structure of overlying strata in shallow coal seam.Journal of China Coal Society,2009,34(7):865-869(In Chinese).4Wei M Y,Wang E Y,Liu X F,Song D Z,Zhang Y.Numerical Simulation of Roof Fracture Under Dynamic Disturbance.Journal of Mining&Safety Engineering,2010,27(4):532-536(In Chinese).5Jia J Q,Wang H T,Tang J X,Li X H,Li K X,Hu G Z.Determination of key strata and interval of roofing breaking of hard and soft composite roofs.Chinese Journal
收藏