3857 直齿圆柱齿轮注射模设计
3857 直齿圆柱齿轮注射模设计,圆柱齿轮,注射,设计
直 齿 圆 柱 齿 轮 注 塑 模 设 计 摘 要:本设计题目为直齿圆柱齿轮注塑模设计,体现了塑料齿轮在受力不大场合代替钢是很有前景的。所以本设计对我今后深入设计齿轮埋下一定的功力。本设计运用塑料成型工艺及模具设计的基础知识,首先分析了塑件的成分及性能要求,为选取浇口的类型做好了准备;然后估算了塑件的体积,便于选取注塑机及确定型腔数量;最后分析了塑件的特征,确定模具的设计参数、设计要点及推出装置的选取。本塑件齿轮外侧的侧孔与开模方向不一致,所以在脱模时必须考虑设计侧抽机构,以便开模过程的时,使塑件能顺利脱模。本副模具采用推管脱模,一模两件。一模多件容易降低同轴精度,推杆脱模亦不易保证齿轮精度。型腔采用镶拼式组合,这样便于加工、热处理,也可以利用其配合间隙来排气。缺点:强度不高,配合面不好的话容易变形。关键词:注塑模 浇口 推块 Spur Gear Injection Mold Design Abstract: The design entitled spur gear injection mold design, reflects the large plastic gear occasions in lieu of steel is very promising. Therefore, the design of the design of future in-depth gear I planted some skill.The use of plastic molding process design and die design of the basic knowledge, the first analysis of the plastic parts of the composition and performance requirements, in order to select the type of gate ready; and then estimated the volume of plastic parts for injection molding machine to select and determine the type cavity number; the final analysis of the characteristics of plastic parts, molds to determine the design parameters, design features and the introduction of the selected device.Plastic parts of the lateral side gear hole direction inconsistent with the open mode, it must be taken into account in the design of Demoulding side pumping in order to open mold process, the plastic parts so that a smooth release. Deputy dies in this release using push tube, a two-mode. A multi-coaxial easy to reduce accuracy, putting Demoulding gear would not be easy to ensure accuracy. Combined use of cavity so easy processing, heat treatment, can also make use of its space to tie in with the exhaust. Disadvantages: intensity is not high, with not so easy to surface deformation.Key words: Injection Molding Gate Push block
收藏
编号:164799
类型:共享资源
大小:1.58MB
格式:RAR
上传时间:2017-10-27
50
积分
- 关 键 词:
-
圆柱齿轮
注射
设计
- 资源描述:
-
3857 直齿圆柱齿轮注射模设计,圆柱齿轮,注射,设计
展开阅读全文
- 温馨提示:
1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 装配图网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
装配图网所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。