3512 塑料后盖塑料成型工艺与模具设计
3512 塑料后盖塑料成型工艺与模具设计,塑料,成型,工艺,模具设计
塑 料 后 盖 设 计摘 要本设计题目为后盖塑料成型工艺及模具设计,体现了盖板类塑料零件的设计要求、内容及方向,有一定的设计意义。通过对该零件模具的设计,进一步加强了设计者注塑模设计的基础知识,为设计更复杂的注塑模具做好了铺垫和吸取了更深刻的经验。本设计运用塑料成型工艺及模具设计的基础知识,首先分析了塑件的成分及性能要求;接着估算了塑件的体积,便于选取注塑机及确定型腔数量;最后分析了塑件的特征,确定模具的设计参数、设计要点及推出装置的选取。根据本塑件结构,两侧必须考虑侧向抽芯,同时抽芯机构的设计应能满足塑件成型要求,本设计采用的是斜滑块侧向抽芯装置,结构复杂程度适中。关键词:注塑模 流道 侧向抽芯 型腔 Plastic rear cover designAbstractThe design of the rear cover the topic of plastic molding and die design process, reflects the type of plastic parts cover the design requirements, content and direction of the design of a certain significance. Parts of the mold through the design, the designer has been further strengthened by the injection mold design based on knowledge, for the design of more complex injection molds made and lessons foreshadowing a more profound experience.The designing of the use of injection molding and die designing of the basic knowledge, the first analysis of the plastic parts of the composition and performance requirements, then estimate the volume of plastic parts, injection molding machines and facilitate the selection of identified Cavity volume of the final pieces of plastic the characteristics of the design parameters established mold, design elements and the introduction of the device selected.Under the structure of plastic parts, both sides must consider pumping lateral movements, while core pulling bodies should be designed to meet the requirements of molding plastic parts, the design is based on oblique lateral slider core pulling devices, moderate complexity of the structure.Keywords: Injection moulding , Runner, Lateral core pulling , Cavity
收藏
编号:164001
类型:共享资源
大小:607.20KB
格式:RAR
上传时间:2017-10-27
50
积分
- 关 键 词:
-
塑料
成型
工艺
模具设计
- 资源描述:
-
3512 塑料后盖塑料成型工艺与模具设计,塑料,成型,工艺,模具设计
展开阅读全文
- 温馨提示:
1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 装配图网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
![提示](https://www.zhuangpeitu.com/images/bang_tan.gif)
装配图网所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。