DELL iDRAC6_BMC 中文配置文档

《DELL iDRAC6_BMC 中文配置文档》由会员分享，可在线阅读，更多相关《DELL iDRAC6_BMC 中文配置文档（9页珍藏版）》请在装配图网上搜索。

1、真诚为您提供优质参考资料，若有不当之处，请指正。要配置，iDRAC6 局域网选项之间进行选择和关闭使用 、 和空格键。在默认配置中启用 iDRAC6 局域网。 局域网，必须启用允许使用 iDRAC6 的设施如基于 Web 的界面、 telnet/SSH 访问 SM CLP 命令行界面、 控制台重定向和虚拟媒体。项目说明常用设置选择网卡（NIC Selection） 按 、 ，和空格键模式之间切换。可用的模式是专用、 共享、 共享与故障转移 LOM2 和故障转移所有 lom 与共享。这些模式将使相应的接口用于向外部世界通信 iDRAC6。 MAC 地址（MAC Address）这是不可编辑的 M

2、AC 地址，iDRAC 网络接口。VLAN 启用选择打开以启用筛选，iDRAC6 的虚拟局域网。VLAN Id如果在为的 VLAN 启用是输入 1 4094 之间的任何 VLAN ID 值。VLAN 优先级如果启用 VLAN 设置为 On s.elect 0-7 之间 VLAN 的优先级注册 iDRAC6 名称选择打开以在 DNS 服务中注册 iDRAC6 名称。 选择关闭如果您不希望用户能够在 DNS 中找到 iDRAC6 名称。iDRAC6 名称如果注册 iDRAC 名称设置为 On，按编辑当前 DNS iDRAC 名称文本字段。 按完成编辑 iDRAC6 名称。 按返回上一级菜单。 iD

3、RAC6 名称必须是一个有效的 DNS 主机名。DHCP 的域名选择上如果您要从网络上的 DHCP 服务获取域的名称。 选择关闭如果要指定域的名称。域名如果域名从 DHCP 设置为 Off 时，按编辑当前域名文本字段。 新闻编辑完成。 按返回上一级菜单。 域名必须是一个有效的 DNS 域，例如 。主机名称字符串若要编辑的新闻。 输入平台事件陷阱 (PET) 警报的主机的名称。项目说明局域网报警已启用选择打开以启用 PET 局域网报警。警报策略项 1选择启用或禁用，激活第一个警报目的地。警报目标 1如果在为的局域网警报已启用是输入的 IP 地址，将转发 PET 局域网报警。IPv4 设置IPv4

4、选择启用，使 IPv4 协议支持。RMCP + 加密密钥新闻编辑值和完成。 RMCP + 加密密钥是 40 字符的十六进制字符串 （字符 0-9、 一 f 和 A-F）。 RMCP + 是 IPMI 的延伸，IPMI 添加身份验证和加密。 默认值是一个字符串的 40 0 （零）。源 IP 地址DHCP 和静态之间进行选择。 选中 DHCP 后从 DHCP 服务器获取以太网 IP 地址、 子网掩码和默认网关的字段。 如果没有 DHCP 服务器在网络上找到，会将该字段都设置为零。选中静以太网 IP 地址、 子网掩码和默认网关项目成为可编辑。以太网 IP 地址如果 IP 地址源设置为 DHCP，此字

5、段将显示从 DHCP 获得 IP 地址。如果 IP 地址源设置为静态，请输入您要分配给该 iDRAC6 的 IP 地址。默认值是插槽的 192.168.0.120 加上包含服务器。子网掩码如果 IP 地址源设置为 DHCP，此字段将显示从 DHCP 获得的子网掩码地址。如果 IP 地址源设置为静态，输入，iDRAC6 的子网掩码。 默认值为 255.255.255.0。项目说明默认网关如果 IP 地址源设置为 DHCP，此字段将显示从 DHCP 获得的默认网关的 IP 地址。如果 IP 地址源设置为静态，输入默认网关的 IP 地址。 默认值是 192.168.0.1。DHCP 的 DNS 服务

6、器选择打开以从网络上的 DHCP 服务中检索的 DNS 服务器地址。 选择关闭以指定下面的 DNS 服务器地址。DNS 服务器 1从 DHCP DNS 服务器关闭时输入第一个 DNS 服务器的 IP 的地址。DNS 服务器 2从 DHCP DNS 服务器关闭时输入第二个 DNS 服务器的 IP 地址。IPv6 设置源 IP 地址选择自动配置和静态之间。 选中自动配置后从 DHCP 获取 IPv6 地址 1、 前缀的长度和默认网关字段。选中静态 IPv6 地址 1、 前缀的长度和默认网关项目成为可编辑。IPv6 地址 1如果 IP 地址源设置为自动配置，此字段将显示从 DHCP 获得 IP 地址

7、。如果 IP 地址源设置为静态，请输入您要分配给该 iDRAC6 的 IP 地址。前缀长度如果 IP 地址源设置为自动配置，此字段将显示网络前缀长度。如果 IP 地址源设置为静态，输入网络前缀的长度。项目说明默认网关如果 IP 地址源设置为自动配置，此字段将显示从 DHCP 获得的默认网关的 IP 地址。如果 IP 地址源设置为静态，输入默认网关的 IP 地址。IPv6 链接本地地址这是不可编辑的 IPv6 链接本地地址，iDRAC 网络接口。IPv6 地址 2这是不可编辑的 IPv6 地址 2 iDRAC 网络接口。DHCP 的 DNS 服务器选择打开以从网络上的 DHCP 服务中检索的 D

8、NS 服务器地址。 选择关闭以指定下面的 DNS 服务器地址。DNS 服务器 1从 DHCP DNS 服务器关闭时输入第一个 DNS 服务器的 IP 的地址。DNS 服务器 2从 DHCP DNS 服务器关闭时输入第一个 DNS 服务器的 IP 的地址。 先进的局域网配置自动协商如果网卡选择设置为专用，选择启用和禁用之间。选中启用后将自动配置局域网速度设置和 LAN 双工设置。局域网速度设置如果通过自动设置为禁用，选择 10 Mbps 至 100 Mbps。局域网双工设置如果通过自动设置为禁用，半双工和全双工之间进行选择。虚拟媒体按选择 Detached、 连接，或自动连接。 当您选择了连接时

9、虚拟媒体设备连接到提供在控制台重定向会话期间使用的 USB 总线。如果选择 Detached 用户无法访问虚拟媒体设备控制台重定向会议期间。虚拟 Flash按选择禁用或启用。禁用/启用会造成一种分离和一个附加的所有虚拟媒体设备的 USB 总线。禁用将导致虚拟的 Flash，被删除，并变得不可用。按选择启用或已禁用。 此选项配置智能卡登录功能。 可用的选项包括启用、 禁用和与 RACADM 启用。系统服务按选择启用或已禁用。 请参阅统一服务器配置器用户指南，详细信息在戴尔支持网站上提供。取消系统服务按下以选择否或是。当您选择了是时统一服务器配置的所有会话都关闭并重新启动服务器时您保存并退出应用新

10、设置。按选择启用或已禁用。 此选项配置智能卡登录功能。 可用的选项包括启用、 禁用和与 RACADM 启用。按选择启用或已禁用。 此选项配置智能卡登录功能。 可用的选项包括启用、 禁用和与 RACADM 启用。系统事件日志系统事件日志菜单允许您查看系统事件日志 （SEL） 的邮件，并清除日志消息。 按键显示系统事件日志菜单。 系统日志条目进行计数，并显示记录和最新的消息的总数。 SEL 保留最多 512 消息。要清除 SEL 清除选择系统事件日志，并按 。 SEL 菜单完成后按 返回上一级菜单。查看 SEL 消息若要查看 SEL 消息，选择查看系统事件日志，并按 。 使用 移动到上一个 （较早

11、的） 消息 移动到下一个 （较新） 消息。 请输入要跳转到该记录的记录号。 通过查看 SEL 邮件时，请按 。To configure the iDRAC6 LAN option use , , and the spacebar to select between On and Off.The iDRAC6 LAN is enabled in the default configuration. The LAN must be enabled to permit the use of iDRAC6 facilities, such as the Web-based interface, tel

12、net/SSH access to the SM-CLP command line interface, console redirection, and virtual media.ItemDescriptionCommon SettingsNIC SelectionPress , , and spacebar to switch between the modes.The available modes are Dedicated, Shared, Shared with Failover LOM2, and Shared with failover All LOMs.These mode

13、s will allow the iDRAC6 to use the corresponding interface for communication to the outside world. MAC AddressThis is the non-editable MAC address of the iDRAC network interface.VLAN EnableSelect On to enable the Virtual LAN filtering for the iDRAC6.VLAN IdIf VLAN Enable is set to On, enter any VLAN

14、 ID value between 1-4094.VLAN PriorityIf VLAN Enable is set to On, s.elect the priority of the VLAN between 0-7Register iDRAC6 NameSelect On to register the iDRAC6 name in the DNS service. Select Off if you do not want users to be able to find the iDRAC6 name in DNS.iDRAC6 NameIf Register iDRAC Name

15、 is set to On, press to edit the Current DNS iDRAC Name text field. Press when you have finished editing the iDRAC6 name. Press to return to the previous menu. The iDRAC6 name must be a valid DNS host name.Domain Name from DHCPSelect On if you want to obtain the domain name from a DHCP service on th

16、e network. Select Off if you want to specify the domain name.Domain NameIf Domain Name from DHCP is set to Off, press to edit the Current Domain Name text field. Press when you have finished editing. Press to return to the previous menu. The domain name must be a valid DNS domain, for example .Host

17、Name StringPress to edit. Enter the name of the host for Platform Event Trap (PET) alerts.ItemDescriptionLAN Alert EnabledSelect On to enable the PET LAN alert.Alert Policy Entry 1Select Enable or Disable to activate the first alert destination.Alert Destination 1if LAN Alert Enabled is set to On, e

18、nter the IP address where PET LAN alerts will be forwarded.IPv4 SettingsIPv4Select Enabled to enable IPv4 protocol support.RMCP+ Encryption KeyPress to edit the value and when finished. The RMCP+ Encryption key is a 40-character hexadecimal string (characters 0-9, a-f, and A-F). RMCP+ is an IPMI ext

19、ension that adds authentication and encryption to IPMI. The default value is a string of 40 0s (zeros).IP Address SourceSelect between DHCP and Static. When DHCP is selected, the Ethernet IP Address, Subnet Mask, and Default Gateway fields are obtained from a DHCP server. If no DHCP server is found

20、on the network, the fields are set to zeros.When Static is selected, the Ethernet IP Address, Subnet Mask, and Default Gateway items become editable.Ethernet IP AddressIf the IP Address Source is set to DHCP, this field displays the IP address obtained from DHCP.If the IP Address Source is set to St

21、atic, enter the IP address you want to assign to the iDRAC6.The default is 192.168.0.120 plus the number of the slot containing the server.Subnet MaskIf the IP Address Source is set to DHCP, this field displays the subnet mask address obtained from DHCP.If the IP Address Source is set to Static, ent

22、er the subnet mask for the iDRAC6. The default is 255.255.255.0.ItemDescriptionDefault GatewayIf the IP Address Source is set to DHCP, this field displays the IP address of the default gateway obtained from DHCP.If the IP Address Source is set to Static, enter the IP address of the default gateway.

23、The default is 192.168.0.1.DNS Servers from DHCPSelect On to retrieve DNS server addresses from a DHCP service on the network. Select Off to specify the DNS server addresses below.DNS Server 1If DNS Servers from DHCP is Off, enter the IP address of the first DNS server.DNS Server 2If DNS Servers fro

24、m DHCP is Off, enter the IP address of the second DNS server.IPv6 SettingsIP Address SourceSelect between AutoConfig and Static. When AutoConfig is selected, the IPv6 Address 1, Prefix Length, and Default Gateway fields are obtained from DHCP.When Static is selected, the IPv6 Address 1, Prefix Lengt

25、h, and Default Gateway items become editable.IPv6 Address 1If the IP Address Source is set to AutoConfig, this field displays the IP address obtained from DHCP.If the IP Address Source is set to Static, enter the IP address you want to assign to the iDRAC6.Prefix LengthIf the IP Address Source is se

26、t to AutoConfig, this field displays the Prefix length of the network.If the IP Address Source is set to Static, enter the Prefix length of the network.ItemDescriptionDefault GatewayIf the IP Address Source is set to AutoConfig, this field displays the IP address of the default gateway obtained from

27、 DHCP.If the IP Address Source is set to Static, enter the IP address of the default gateway.IPv6 Link-local AddressThis is the non-editable IPv6 Link-local Address of the iDRAC network interface.IPv6 Address 2This is the non-editable IPv6 Address 2 of the iDRAC network interface.DNS Servers from DH

28、CPSelect On to retrieve DNS server addresses from a DHCP service on the network. Select Off to specify the DNS server addresses below.DNS Server 1If DNS Servers from DHCP is Off, enter the IP address of the first DNS server.DNS Server 2If DNS Servers from DHCP is Off, enter the IP address of the fir

29、st DNS server. Advanced LAN ConfigurationsAuto-NegotiateIf NIC Selection is set to Dedicated, select between Enabled and Disabled.When Enabled is selected, LAN Speed Setting and LAN Duplex Setting are configured automatically.LAN Speed SettingIf Auto-Negotiate is set to Disabled, select between 10 M

30、bps and 100 Mbps.LAN Duplex SettingIf Auto-Negotiate is set to Disabled, select between Half Duplex and Full Duplex.Virtual MediaPress to select Detached, Attached, or Auto-Attached. When you select Attached, the virtual media devices are attached to the USB bus, making them available for use during

31、 Console Redirection sessions.If you select Detached, users cannot access virtual media devices during Console Redirection sessions.Virtual FlashPress to select Disabled or Enabled.Disable/Enable will cause a Detach and an Attach of all Virtual Media devices from the USB bus.Disable will cause the V

32、irtual Flash to be removed and to become unavailable for use.Press to select Enabled or Disabled. This option configures the Smart Card Logon feature. The available options are Enabled, Disabled, and Enabled with RACADM.System ServicesPress to select Enabled or Disabled. See the Unified Server Confi

33、gurator User Guide, available on the Dell Support Website at , for more information.Cancel System ServicesPress to select No or Yes.When you select Yes, all Unified Server Configurator sessions are closed and the server is restarted when you Save and Exit to apply the new settings.Press to select En

34、abled or Disabled. This option configures the Smart Card Logon feature. The available options are Enabled, Disabled, and Enabled with RACADM.Press to select Enabled or Disabled. This option configures the Smart Card Logon feature. The available options are Enabled, Disabled, and Enabled with RACADM.

35、System Event LogThe System Event Log Menu allows you to view System Event Log (SEL) messages and to clear the log messages. Press to display the System Event Log Menu. The system counts the log entries and then displays the total number of records and the most recent message. The SEL retains a maxim

36、um of 512 messages.To clear the SEL, select Clear the System Event Log and press . When you have finished with the SEL menu, press to return to the previous menu.Viewing SEL MessagesTo view SEL messages, select View System Event Log and press . Use to move to the previous (older) message and to move to the next (newer) message. Enter a record number to jump to that record. Press when you are through viewing SEL messages.9 / 9