SUN-M5000设置及安装笔记

《SUN-M5000设置及安装笔记》由会员分享，可在线阅读，更多相关《SUN-M5000设置及安装笔记（92页珍藏版）》请在装配图网上搜索。

1、SUN M5000安装笔记（内部使用 请勿外传） Sun M5000Solaris 10系统的安装、打补丁及IPMP的配置目 录一、安装准备3节 1.011 M5000的初始设置4节 1.022 添加用户及给机器加电4二、安装系统15三、打补丁49四、做镜像86五、配置IPMP92一、安装准备首先使用串口线将笔记本与M5000连接，端口的设置请看（图 1-1）：图 1-1操作系统安装以及IP地址配置如下：Solaris版本要求Solaris 10_U7使用语言en_US 是否添加中文或者其他附加的语言包添加简体中文及北美USA语言包主机名m5000IP地址192.168.0.2子网掩码255.

2、255.255.0系统的分区如下：SliceSize（MB）Mount point030000/ /*这是根分区*/116000swap /*这是交换分区*/2350000/oracle4567512Metadb分区节 1.01 1 M5000的初始设置新出厂的机器，XSCF没有设置用户，需要使用串口进行初始用户的创建。机器加插上电源后，XSCF启动完成后出现登陆提示符：Dec 24 08:52:26 localhost XSCF104: XSCF Initialize complete.login:default Change the panel mode switch to Service

3、 and press return. (Operation : Locked state - Service - Return)Leave it in that position for at least 5 seconds. Change the panel mode switch to Locked, and press return. (Operation : Wait more than 5 seconds - Service state - Locked - Return)XSCF根据提示，输入用户名default后，将前面板钥匙由锁定位置拧到维护位置，按回车，等待5秒后，将钥匙由维

4、护位置拧到 锁定位置，敲回车，这样系统就进入XSCF提示符了。（钥匙顺序也可以相反，即开始本来在维护位置，那么就拧到锁定，再由锁定到维护）节 1.02 2 添加用户及给机器加电Change the panel mode switch to Service and press return.Leave it in that position for at least 5 seconds. Change the panel mode switch to Locked, and press return.XSCF adduser eis-installerXSCF setprivileges eis

5、-installer platadm useradm auditadm /*添加用户并设置权限*/*添加用户eis-installer并设置权限，主要是platadm useradm*/XSCF showuser l /*查看状态*/User Name: eis-installerUID: 100Status: EnabledMinimum: 0Maximum: 99999Warning: 7Inactive: -1Last Change: Dec 24, 2009Password Expires: NeverPassword Inactive: NeverAccount Expires: N

6、everPrivileges: useradm platadm auditadmXSCF password eis-installer /*修改密码,此M5000密码为admin123*/New XSCF password: BAD PASSWORD: it is too shortRetype new XSCF password: Sorry, passwords do not matchNew XSCF password: BAD PASSWORD: it is based on a dictionary wordRetype new XSCF password: XSCF XSCF XS

7、CF XSCF XSCF exitlogoutlogin: eis-installerPassword: XSCF XSCF XSCF XSCF XSCF showhardconf /*加电后的M5000用此条命令确认内部配置*/SPARC Enterprise M5000; + Serial:BEF0949C90; Operator_Panel_Switch:Locked; + Power_Supply_System:Single; SCF-ID:XSCF#0; + System_Power:Off; System_Phase:Cabinet Power Off; Domain#0 Doma

8、in_Status:Powered Off; MBU_B Status:Normal; Ver:0201h; Serial:BE0948104A ; + FRU-Part-Number:CF00541-0478 08 /541-0478-08 ; + Memory_Size:32 GB; CPUM#0-CHIP#0 Status:Normal; Ver:0401h; Serial:PP094605MN ; + FRU-Part-Number:CA06761-D202 E1 /375-3568-05 ; + Freq:2.400 GHz; Type:32; + Core:4; Strand:2;

9、 CPUM#0-CHIP#1 Status:Normal; Ver:0401h; Serial:PP094605MN ; + FRU-Part-Number:CA06761-D202 E1 /375-3568-05 ; + Freq:2.400 GHz; Type:32; + Core:4; Strand:2; CPUM#1-CHIP#0 Status:Normal; Ver:0401h; Serial:PP0946056Q ; + FRU-Part-Number:CA06761-D202 E1 /375-3568-05 ; + Freq:2.400 GHz; Type:32; + Core:

10、4; Strand:2; CPUM#1-CHIP#1 Status:Normal; Ver:0401h; Serial:PP0946056Q ; + FRU-Part-Number:CA06761-D202 E1 /375-3568-05 ; + Freq:2.400 GHz; Type:32; + Core:4; Strand:2; MEMB#0 Status:Normal; Ver:0101h; Serial:BF0944FVV3 ; + FRU-Part-Number:CF00541-0545 08 /541-0545-08 ; MEM#0A Status:Normal; + Code:

11、ce0000000000000001M3 93T5660QZA-CE6 4151-522563a9; + Type:2A; Size:2 GB; MEM#0B Status:Normal; + Code:ce0000000000000001M3 93T5660QZA-CE6 4151-5225644f; + Type:2A; Size:2 GB; MEM#1A Status:Normal; + Code:ce0000000000000001M3 93T5660QZA-CE6 4151-522563aa; + Type:2A; Size:2 GB; MEM#1B Status:Normal; +

12、 Code:ce0000000000000001M3 93T5660QZA-CE6 4151-52256376; + Type:2A; Size:2 GB; MEM#2A Status:Normal; + Code:ce0000000000000001M3 93T5660QZA-CE6 4151-522563fd; + Type:2A; Size:2 GB; MEM#2B Status:Normal; + Code:ce0000000000000001M3 93T5660QZA-CE6 4151-52256377; + Type:2A; Size:2 GB; MEM#3A Status:Nor

13、mal; + Code:ce0000000000000001M3 93T5660QZA-CE6 4151-5225640a; + Type:2A; Size:2 GB; MEM#3B Status:Normal; + Code:ce0000000000000001M3 93T5660QZA-CE6 4151-522563b7; + Type:2A; Size:2 GB; MEMB#1 Status:Normal; Ver:0101h; Serial:BF0944FVVD ; + FRU-Part-Number:CF00541-0545 08 /541-0545-08 ; MEM#0A Stat

14、us:Normal; + Code:ce0000000000000001M3 93T5660QZA-CE6 4151-522551be; + Type:2A; Size:2 GB; MEM#0B Status:Normal; + Code:ce0000000000000001M3 93T5660QZA-CE6 4151-522551bf; + Type:2A; Size:2 GB; MEM#1A Status:Normal; + Code:ce0000000000000001M3 93T5660QZA-CE6 4151-52256405; + Type:2A; Size:2 GB; MEM#1

15、B Status:Normal; + Code:ce0000000000000001M3 93T5660QZA-CE6 4151-52256400; + Type:2A; Size:2 GB; MEM#2A Status:Normal; + Code:ce0000000000000001M3 93T5660QZA-CE6 4151-522551ba; + Type:2A; Size:2 GB; MEM#2B Status:Normal; + Code:ce0000000000000001M3 93T5660QZA-CE6 4151-522551bb; + Type:2A; Size:2 GB;

16、 MEM#3A Status:Normal; + Code:ce0000000000000001M3 93T5660QZA-CE6 4151-522551b0; + Type:2A; Size:2 GB; MEM#3B Status:Normal; + Code:ce0000000000000001M3 93T5660QZA-CE6 4151-522551b9; + Type:2A; Size:2 GB; DDC_A#0 Status:Normal; DDC_A#1 Status:Normal; DDC_A#2 Status:Normal; DDC_A#3 Status:Normal; DDC

17、_B#0 Status:Normal; DDC_B#1 Status:Normal; IOU#0 Status:Normal; Ver:0101h; Serial:BF0941ENU2 ; + FRU-Part-Number:CF00541-2240 05 /541-2240-05 ; DDC_A#0 Status:Normal; DDCR Status:Normal; DDC_B#0 Status:Normal; XSCFU Status:Normal,Active; Ver:0101h; Serial:BF0941EM56 ; + FRU-Part-Number:CF00541-0481

18、04 /541-0481-04 ; OPNL Status:Normal; Ver:0101h; Serial:BF0941EDBC ; + FRU-Part-Number:CF00541-0850 06 /541-0850-06 ; PSU#0 Status:Normal; Serial:0017527-0940025271; + FRU-Part-Number:CF00300-2011 0250 /300-2011-02-50; + Power_Status:Off; AC:200 V; PSU#1 Status:Normal; Serial:0017527-0940025268; + F

19、RU-Part-Number:CF00300-2011 0250 /300-2011-02-50; + Power_Status:Off; AC:200 V; PSU#2 Status:Normal; Serial:0017527-0940025267; + FRU-Part-Number:CF00300-2011 0250 /300-2011-02-50; + Power_Status:Off; AC:200 V; PSU#3 Status:Normal; Serial:0017527-0940025266; + FRU-Part-Number:CF00300-2011 0250 /300-

20、2011-02-50; + Power_Status:Off; AC:200 V; FANBP_C Status:Normal; Ver:0501h; Serial:BF0940EA5H ; + FRU-Part-Number:CF00541-3099 01 /541-3099-01 ; FAN_A#0 Status:Normal; FAN_A#1 Status:Normal; FAN_A#2 Status:Normal; FAN_A#3 Status:Normal;XSCF settimezone -c settz -s Asia/Shanghai /*设置时区及时间，完成后重启XSCF*/

21、Asia/ShanghaiXSCF showdateThu Dec 24 16:56:06 CST 2009XSCF XSCF setdscp /*设置管理网口IP地址DSCP network 0.0.0.0 192.168.0.0DSCP netmask 255.255.255.0 XSCF address 192.168.0.1 192.168.0.3Domain #00 address 192.168.0.2 192.168.0.4Domain #01 address 192.168.0.3 192.168.0.5Domain #02 address 192.168.0.4 192.16

22、8.0.6Domain #03 address 192.168.0.5 192.168.0.7Commit these changes to the database? y|n : yXSCF showdscpDSCP Configuration: Network: 192.168.0.0Netmask: 255.255.255.0 Location Address- -XSCF 192.168.0.3Domain #00 192.168.0.4Domain #01 192.168.0.5Domain #02 192.168.0.6Domain #03 192.168.0.7XSCF rebo

23、otxscfThe XSCF will be reset. Continue? y|n :yexecute K000endXSCF - completeexecute S10ioxoff - completeDec 24 08:56:51 localhost XSCF104: XSCF shutdown sequence startexecute K000end - completeexecute K100end - completeexecute K101end - completeunmount /hcp0/linuxunmount /hcp0/scfprogunmount /hcp0/g

24、endata - completeunmount /hcp0/remcscm - completeunmount /hcp1/linuxunmount /hcp1/scfprogunmount /hcp1/gendataunmount /hcp1/remcscmunmount /hcpcommon/setup - completeunmount /hcpcommon/obp - completeunmount /hcpcommon/tmp - completeunmount /hcpcommon/varunmount /hcpcommon/scflog1 - completeunmount /

25、hcpcommon/scflog2 - completeXSCF reset.Please stand by while rebooting the system.(15)Restarting system.XSCF uboot 01080001 (May 8 2009 - 15:09:36)XSCF uboot 01080001 (May 8 2009 - 15:09:36)SCF board boot factor = 4040 DDR Real size: 256 MB DDR: 224 MB# Booting image at ff800000 . Image Name: XSCF k

26、ernel 01090000 2.6.11.12-s Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1456903 Bytes = 1.4 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum . OK Uncompressing Kernel Image . OK# Loading RAMDisk Image at ff980000 . Image Name: XSCF rootfs 01090000 ,2009/07/30

27、 Image Type: PowerPC Linux RAMDisk Image (gzip compressed) Data Size: 5457580 Bytes = 5.2 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum . OK Loading Ramdisk to 0bacb000, end 0bfff6ac . OKLinux version 2.6.11.12-sec (gcc version 3.4.4) #1 Thu Jul 30 14:14:57 JST 2009new message b

28、uffer at 0f700000 size 1048576log_buf_len: 1048576mpc85xx_cds_setup_archBuilt 1 zonelistsKernel command line: root=/dev/ram rw console=ttyS0,9600 init=/sbin/init_change_root panic=1 mem=240MOpenPIC Version 1.2 (1 CPUs and 44 IRQ sources) at fbe79000PID hash table entries: 1024 (order: 10, 16384 byte

29、s)Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)Memory: 218752k available (2188k kernel code, 668k data, 316k init, 0k highmem)Mount-cache hash table entries: 512 (order: 0, 4096 bytes)Freeing initrd memory: 5329k freedRAM

30、DISK driver initialized: 16 RAM disks of 32768K size 1024 blocksizei2c-algo-cpm: CPM2 I2C algorithm module version 0.1 (Mar 22, 2005)FCC ENET Version 0.3TCP established hash table entries: 8192 (order: 4, 65536 bytes)TCP bind hash table entries: 8192 (order: 3, 32768 bytes)ip_tables: (C) 2000-2002 N

31、etfilter core teamarp_tables: (C) 2002 David S. MillerVFS: Mounted root (ext2 filesystem).Freeing unused kernel memory: 316k initswitching initrd filesystem, ramdisk to tmpfsSCF Linux Boot Script 2006/03/04 for ROM boot environmentfsl-sec2 hardware crypt accelerator model3a ver 0.02 enabledXSCF init

32、ial process start (pid=104)load /scf/modules/lites_ldrv.ko - completeload /scf/modules/drvscftrace.ko - completeload /scf/modules/sec2_rsa.ko - completeload /scf/modules/sec2_md5.ko - completeload /scf/modules/sec2_des.ko - completeload /scf/modules/sec2_arc4.ko - completeload /scf/modules/sec2_aes.

33、ko - completeload /scf/modules/sec2_sha256.ko - completeload /scf/modules/sec2_sha1.ko - completeload /scf/modules/hw_random.ko - completeload /scf/modules/scsi_mod.ko - completeload /scf/modules/sd_mod.ko - completeload /scf/modules/usbcore.ko - completeload /scf/modules/ohci-hcd.ko - completeload

34、/scf/modules/usb-storage.ko - completeload /scf/modules/drvbootfmem.ko - completeload /scf/modules/drvmbc.ko - completeload /scf/modules/drvnand.ko - completeload /scf/modules/drvffc.ko - completeload /scf/modules/drvffcint.ko - completeload /scf/modules/drvrtc.ko - completeload /scf/modules/drvxscf

35、uart.ko - completeload /scf/modules/drvrci.ko - completeload /scf/modules/drvtimer.ko - completeload /scf/modules/drvsdic.ko - completeload /scf/modules/sm2s.ko - completeload /scf/modules/spkmdrv.ko - completemount /dev/mtdblock0 - /hcp0/linux - completemount /dev/mtdblock1 - /hcp0/scfprog - comple

36、temount /dev/mtdblock2 - /hcp0/gendata - completemount /dev/mtdblock3 - /hcp0/remcscm - completemount /dev/mtdblock4 - /hcpcommon/setup - completemount /dev/mtdblock5 - /hcpcommon/obp - completemount /dev/mtdblock6 - /hcpcommon/tmp - completemount /dev/mtdblock11 - /hcpcommon/var - completemount /de

37、v/mtdblock12 - /hcpcommon/scflog1 - completemount /dev/mtdblock13 - /hcpcommon/scflog2 - completeexecute S00mtab - completeexecute S00portmap - completeexecute S00tmpmake - completeexecute S00varclean - completeexecute S10ldconfig - completeexecute S15last_dmesg - completeexecute S20cfgcreate - comp

38、leteexecute S50iptables - completeexecute S60check - completeexecute S61restore - completeexecute S99syslogd - completeinitialize XSCF common database (STANDALONE) - completestart /scf/sbin/dbs (pid=302)start /scf/sbin/ksyseventd (pid=303)start /scf/sbin/syseventd (pid=308)start /scf/init/scf_cmgrd

39、(pid=323)start /scf/init/scf_coremgr (pid=324)start /scf/init/dualprocess (pid=325)check SCF operation mode (for OPNL access) - completeinitialize OPNL - completecheck SCF operation mode - complete (ACTIVE)start /scf/sbin/dbs (pid=337)initialize XSCF common database (OWN) - completesynchronize setup

40、 data (XSCF - OPNL) - completeinitialize XSCF common database (ACTIVE) - completewait for database synchronization - completeexecute S00clis_all - completeexecute S10restore_um - completeexecute S11network.sh - completeexecute S15ntpcheck.sh - completeexecute S21daemons - completeexecute S51scflog_S

41、CFboot.sh - completeexecute S82cod - completeexecute S98bui - completeexecute S00clis_active - completeexecute S00cmem_check - completeexecute S00tmp_login - completeexecute S18restorefmdlog - completeexecute S19setfmurl - completeexecute S29setfmconf - completeexecute S50setupSCFboot.sh - completee

42、xecute S83setservicetagdata - completestart /scf/sbin/scf_panelmgr (pid=640)start /scf/sbin/auditd (pid=641)start /scf/sbin/cmd (pid=642)start /scf/sbin/cmd_sub (pid=643)start /scf/sbin/errhandd (pid=644)start /scf/sbin/fjdrd (pid=645)start /scf/sbin/frura (pid=646)start /scf/sbin/mond (pid=647)star

43、t /scf/sbin/mond (pid=648)start /scf/sbin/powerd (pid=649)start /scf/sbin/rci (pid=650)start /scf/sbin/rci_dual (pid=651)start /scf/sbin/reset (pid=652)start /scf/sbin/resetra (pid=653)start /scf/sbin/rsyncprocess (pid=654)start /scf/sbin/scf_firmup_exed (pid=655)start /scf/sbin/scf_hardlog (pid=656

44、)start /scf/sbin/scf_loganalyze (pid=657)start /scf/sbin/scf_procmeas (pid=658)start /scf/sbin/sequence (pid=659)start /scf/sbin/ttyd (pid=660)start /scf/sbin/apcsd (pid=661)start /scf/sbin/codd (pid=662)start /scf/sbin/scf_firmup_ctld (pid=663)start /scf/sbin/fmd (pid=664)start /scf/sbin/dscpd (pid

45、=722)start /scf/sbin/monitor_msg (pid=723)start /scf/sbin/picld (pid=724)start /scf/sbin/sunmcrund (pid=725)start /scf/sbin/stdiscoverer (pid=726)start /scf/sbin/stlistener (pid=727)start /scf/sbin/dfrud (pid=728)start /scf/sbin/iomgrd (pid=729)start /scf/sbin/archd (pid=772)wait for SCF_READY - com

46、pleteexecute S20setupSCFready.sh - completeexecute S99rcclear - completeexecute S10iobox_scan - completeexecute S10restore_um - completeexecute S84snmpd - completeexecute S85sunmc_esd - completeexecute S86limits - completeexecute S87opnl - completeexecute S99dr_recover.sh - completeXSCF Initialize c

47、omplete.Dec 24 17:01:03 localhost XSCF104: XSCF Initialize complete.login: eis-installerPassword: XSCF XSCF poweron -d 0DomainIDs to power on:00Continue? y|n :y00 :Powering on*Note* This command only issues the instruction to power-on. The result of the instruction can be checked by the showlogs pow

48、er.XSCF console -d 0Connect to DomainID 0?y|n :yPOST Sequence 01 CPU CheckPOST Sequence 02 BannerLSB#00 (XSB#00-0): POST 2.11.0 (2009/06/18 09:29)POST Sequence 03 Fatal CheckPOST Sequence 04 CPU RegisterPOST Sequence 05 STICKPOST Sequence 06 MMUPOST Sequence 07 Memory InitializePOST Sequence 08 Memo

49、ryPOST Sequence 09 Raw UE In CachePOST Sequence 0A Floating Point UnitPOST Sequence 0B SCPOST Sequence 0C Cacheable InstructionPOST Sequence 0D SoftintPOST Sequence 0E CPU Cross CallPOST Sequence 0F CMU-CHPOST Sequence 10 PCI-CHPOST Sequence 11 Master DevicePOST Sequence 12 DSCPPOST Sequence 13 SC C

50、heck Before STICK DiagPOST Sequence 14 STICK StopPOST Sequence 15 STICK StartPOST Sequence 16 Error CPU CheckPOST Sequence 17 System ConfigurationPOST Sequence 18 System Status CheckPOST Sequence 19 System Status Check After SyncPOST Sequence 1A OpenBoot Start.POST Sequence Complete.Sun SPARC Enterp

51、rise M5000 Server, using Domain consoleCopyright 2009 Sun Microsystems, Inc. All rights reserved.Copyright 2009 Sun Microsystems, Inc. and Fujitsu Limited. All rights reserved.OpenBoot 4.24.11, 32768 MB memory installed, Serial #88430282.Ethernet address 0:21:28:45:56:ca, Host ID: 854556ca.Dec 24 17

52、:04:44 localhost dscpd722: Failed to start DSCP for domain0 (error=2)Boot device: disk File and args: SunOS Release 5.10 Version Generic_141414-10 64-bitCopyright 1983-2009 Sun Microsystems, Inc. All rights reserved.Use is subject to license terms.二、安装系统在OK模式下从光盘启动12 ok 12 ok boot cdrom /*进入OK模式下，通过

53、cdrom启动*/Resetting.POST Sequence 01 CPU CheckPOST Sequence 02 BannerLSB#00 (XSB#00-0): POST 2.11.0 (2009/06/18 09:29)POST Sequence 03 Fatal CheckPOST Sequence 04 CPU RegisterPOST Sequence 05 STICKPOST Sequence 06 MMUPOST Sequence 07 Memory InitializePOST Sequence 08 MemoryPOST Sequence 09 Raw UE In

54、CachePOST Sequence 0A Floating Point UnitPOST Sequence 0B SCPOST Sequence 0C Cacheable InstructionPOST Sequence 0D SoftintPOST Sequence 0E CPU Cross CallPOST Sequence 0F CMU-CHPOST Sequence 10 PCI-CHPOST Sequence 11 Master DevicePOST Sequence 12 DSCPPOST Sequence 13 SC Check Before STICK DiagPOST Se

55、quence 14 STICK StopPOST Sequence 15 STICK StartPOST Sequence 16 Error CPU CheckPOST Sequence 17 System ConfigurationPOST Sequence 18 System Status CheckPOST Sequence 19 System Status Check After SyncPOST Sequence 1A OpenBoot Start.POST Sequence Complete.Sun SPARC Enterprise M5000 Server, using Domain consoleCopyright 2009 Sun Microsystems, Inc. All rights reserved.Copyright 2009 Sun Microsystems, Inc. and Fujitsu Limited. All rights reserved.OpenBoot 4.24.11, 32768 MB memory installed, Serial #88430282.Ethernet address 0:21:28:45:56:ca, Host ID: 854556