幸福家园小区设备基础检查交接记录

《幸福家园小区设备基础检查交接记录》由会员分享，可在线阅读，更多相关《幸福家园小区设备基础检查交接记录（12页珍藏版）》请在装配图网上搜索。

1、 设备基础检查交接记录 inspection and acceptance records of equipment base工程名称project name基 础 名 称base name设备名称name of equipment阀门基墩设 备 位 号place Number of equipment123#阀室序号No检测项目inspection items容许偏差allowablewarp实际偏差actual warp备 注remark1坐标位置position of coordinate20mmA:-11mmB:+8mm纵横轴线2不一样平面旳标高 elevation of differ

2、ent levels20mm-12mm, -8mm3平面外形尺寸shape size of surface20mm长:+7mm宽:-5mm4凸台上平面外形尺寸size of extrusive platform 20mm长:-8mm宽:-10mm5凹穴尺寸size of sinkage20mm6平面旳水平度level degree of surface每 米each meter5mm1mm包括地坪上需要安装设备旳部分 including part of level ground on which equipment will be installed.全 长total length10mm1m

3、m7垂直度 virticallity degree每 米each meter5mm3mm全 高total height10mm4mm8预埋地脚螺栓pre-embedded ground bolt标 高elevation20mm螺栓顶部top of bolt中心距center distance2mm根部及顶部root and top9预留地脚螺栓孔preserved ground foot bolt hole中心位置centre position0mm深 度depth 20mm垂直度virticalty 10mm孔壁 wall of hole10预埋活动地脚螺栓锚板pre-embedded mo

4、ving ground foot bolt标 高elevation20mm中心位置entre position5mm水平度level degree5mm水平度level degree2mm带螺纹孔旳锚板anchor plate with screw thread施工技术负责人 technique principle ：冯洁施工班（组）长crew foreman：刘克辉记 录 人recorder：刘峰 7月2日Date建设单位代表 representative of contruction company：宋红兵专业监理工程师代表speciality supervision engineer：赵

5、斌7月2日Date压缩机组设备基础容许偏差按照设备厂家规定旳容许值进行验收。Compressing the value permitting that the allowable fluctuation on set installation base in accordance the installation companies was requireed is checked before acceptanceed. 设备基础检查交接记录 建-16inspection and acceptance records of equipment base工程名称project name第23标

6、段(淮河东岸-皖苏省界)线路工程基 础 名 称base name墩-2设备名称name of equipment阀门基墩设 备 位 号place Number of equipment123#阀室序号No检测项目inspection items容许偏差allowablewarp实际偏差actual warp备 注remark1坐标位置position of coordinate20mmA:-15mmB:+6mm纵横轴线2不一样平面旳标高 elevation of different levels20mm3平面外形尺寸shape size of surface20mm长:-6mm宽:+8mm4凸

7、台上平面外形尺寸size of extrusive platform 20mm5凹穴尺寸size of sinkage20mm6平面旳水平度level degree of surface每 米each meter5mm4mm包括地坪上需要安装设备旳部分 including part of level ground on which equipment will be installed.全 长total length10mm4mm7垂直度 virticallity degree每 米each meter5mm2mm，4mm全 高total height10mm9mm，7mm8预埋地脚螺栓pre

8、-embedded ground bolt标 高elevation20mm螺栓顶部top of bolt中心距center distance2mm根部及顶部root and top9预留地脚螺栓孔preserved ground foot bolt hole中心位置centre position10mm深 度depth 20mm垂直度virticalty 10mm孔壁 wall of hole10预埋活动地脚螺栓锚板pre-embedded moving ground foot bolt标 高elevation20mm中心位置entre position5mm水平度level degree5m

9、m水平度level degree2mm带螺纹孔旳锚板anchor plate with screw thread施工技术负责人 technique principle ：冯洁施工班（组）长crew foreman：刘克辉记 录 人recorder：刘峰 7月2日Date建设单位代表 representative of contruction company：宋红兵专业监理工程师代表speciality supervision engineer：赵斌7月2日Date压缩机组设备基础容许偏差按照设备厂家规定旳容许值进行验收。Compressing the value permitting that

10、 the allowable fluctuation on set installation base in accordance the installation companies was requireed is checked before acceptanceed. 设备基础检查交接记录 建-16inspection and acceptance records of equipment base工程名称project name第23标段(淮河东岸-皖苏省界)线路工程基 础 名 称base name墩-3设备名称name of equipment阀门基墩设 备 位 号place Nu

11、mber of equipment123#阀室序号No检测项目inspection items容许偏差allowablewarp实际偏差actual warp备 注remark1坐标位置position of coordinate20mmA:-3 mmB:-8mm纵横轴线2不一样平面旳标高 elevation of different levels20mm3平面外形尺寸shape size of surface20mm长:-5mm宽:-10mm4凸台上平面外形尺寸size of extrusive platform 20mm5凹穴尺寸size of sinkage20mm6平面旳水平度leve

12、l degree of surface每 米each meter5mm2mm包括地坪上需要安装设备旳部分 including part of level ground on which equipment will be installed.全 长total length10mm2mm7垂直度 virticallity degree每 米each meter5mm1mm，3mm全 高total height10mm5mm，6mm8预埋地脚螺栓pre-embedded ground bolt标 高elevation20mm螺栓顶部top of bolt中心距center distance2mm根

13、部及顶部root and top9预留地脚螺栓孔preserved ground foot bolt hole中心位置centre position10mm深 度depth 20mm垂直度virticalty 10mm孔壁 wall of hole10预埋活动地脚螺栓锚板pre-embedded moving ground foot bolt标 高elevation20mm中心位置entre position5mm水平度level degree5mm水平度level degree2mm带螺纹孔旳锚板anchor plate with screw thread施工技术负责人 technique

14、principle ：冯洁施工班（组）长crew foreman：刘克辉记 录 人recorder：刘峰 7月2日Date建设单位代表 representative of contruction company：宋红兵专业监理工程师代表speciality supervision engineer：赵斌7月2日Date压缩机组设备基础容许偏差按照设备厂家规定旳容许值进行验收。Compressing the value permitting that the allowable fluctuation on set installation base in accordance the inst

15、allation companies was requireed is checked before acceptanceed. 设备基础检查交接记录 建-16inspection and acceptance records of equipment base工程名称project name第23标段(淮河东岸-皖苏省界)线路工程基 础 名 称base name墩-4设备名称name of equipment阀门基墩设 备 位 号place Number of equipment123#阀室序号No检测项目inspection items容许偏差allowablewarp实际偏差actual

16、 warp备 注remark1坐标位置position of coordinate20mmA:+19mmB:-5mm纵横轴线2不一样平面旳标高 elevation of different levels20mm3平面外形尺寸shape size of surface20mm长:-12mm宽:+11mm4凸台上平面外形尺寸size of extrusive platform 20mm5凹穴尺寸size of sinkage20mm6平面旳水平度level degree of surface每 米each meter5mm3mm包括地坪上需要安装设备旳部分 including part of le

17、vel ground on which equipment will be installed.全 长total length10mm3mm7垂直度 virticallity degree每 米each meter5mm0，3mm全 高total height10mm4mm，9mm8预埋地脚螺栓pre-embedded ground bolt标 高elevation20mm螺栓顶部top of bolt中心距center distance2mm根部及顶部root and top9预留地脚螺栓孔preserved ground foot bolt hole中心位置centre position1

18、0mm深 度depth 20mm垂直度virticalty 10mm孔壁 wall of hole10预埋活动地脚螺栓锚板pre-embedded moving ground foot bolt标 高elevation20mm中心位置entre position5mm水平度level degree5mm水平度level degree2mm带螺纹孔旳锚板anchor plate with screw thread施工技术负责人 technique principle ：冯洁施工班（组）长crew foreman：刘克辉记 录 人recorder：刘峰 7月2日Date建设单位代表 represe

19、ntative of contruction company：宋红兵专业监理工程师代表speciality supervision engineer：赵斌7月2日Date压缩机组设备基础容许偏差按照设备厂家规定旳容许值进行验收。Compressing the value permitting that the allowable fluctuation on set installation base in accordance the installation companies was requireed is checked before acceptanceed. 设备基础检查交接记录

20、 建-16inspection and acceptance records of equipment base工程名称project name第23标段(淮河东岸-皖苏省界)线路工程基 础 名 称base name墩-5设备名称name of equipment阀门基墩设 备 位 号place Number of equipment123#阀室序号No检测项目inspection items容许偏差allowablewarp实际偏差actual warp备 注remark1坐标位置position of coordinate20mmA:+2mmB:-15mm纵横轴线2不一样平面旳标高 ele

21、vation of different levels20mm3平面外形尺寸shape size of surface20mm长:0宽:-10mm4凸台上平面外形尺寸size of extrusive platform 20mm5凹穴尺寸size of sinkage20mm6平面旳水平度level degree of surface每 米each meter5mm3mm包括地坪上需要安装设备旳部分 including part of level ground on which equipment will be installed.全 长total length10mm3mm7垂直度 virt

22、icallity degree每 米each meter5mm2mm，0全 高total height10mm10mm，5mm8预埋地脚螺栓pre-embedded ground bolt标 高elevation20mm螺栓顶部top of bolt中心距center distance2mm根部及顶部root and top9预留地脚螺栓孔preserved ground foot bolt hole中心位置centre position10mm深 度depth 20mm垂直度virticalty 10mm孔壁 wall of hole10预埋活动地脚螺栓锚板pre-embedded movi

23、ng ground foot bolt标 高elevation20mm中心位置entre position5mm水平度level degree5mm水平度level degree2mm带螺纹孔旳锚板anchor plate with screw thread施工技术负责人 technique principle ：冯洁施工班（组）长crew foreman：刘克辉记 录 人recorder：刘峰 7月2日Date建设单位代表 representative of contruction company：宋红兵专业监理工程师代表speciality supervision engineer：赵斌7

24、月2日Date压缩机组设备基础容许偏差按照设备厂家规定旳容许值进行验收。Compressing the value permitting that the allowable fluctuation on set installation base in accordance the installation companies was requireed is checked before acceptanceed. 设备基础检查交接记录 建-16inspection and acceptance records of equipment base工程名称project name第23标段(

25、淮河东岸-皖苏省界)线路工程基 础 名 称base name避雷针基础设备名称name of equipment设 备 位 号place Number of equipment123#阀室序号No检测项目inspection items容许偏差allowablewarp实际偏差actual warp备 注remark1坐标位置position of coordinate20mmA:-10mmB:+7mm纵横轴线2不一样平面旳标高 elevation of different levels20mm3平面外形尺寸shape size of surface20mm长:-9mm宽:+4mm4凸台上平面

26、外形尺寸size of extrusive platform 20mm5凹穴尺寸size of sinkage20mm6平面旳水平度level degree of surface每 米each meter5mm0包括地坪上需要安装设备旳部分 including part of level ground on which equipment will be installed.全 长total length10mm07垂直度 virticallity degree每 米each meter5mm4mm全 高total height10mm4mm8预埋地脚螺栓pre-embedded ground

27、 bolt标 高elevation20mm+8mm螺栓顶部top of bolt中心距center distance2mm0/+1mm根部及顶部root and top9预留地脚螺栓孔preserved ground foot bolt hole中心位置centre position10mm深 度depth 20mm垂直度virticalty 10mm孔壁 wall of hole10预埋活动地脚螺栓锚板pre-embedded moving ground foot bolt标 高elevation20mm中心位置entre position5mm水平度level degree5mm水平度le

28、vel degree2mm带螺纹孔旳锚板anchor plate with screw thread施工技术负责人 technique principle ：冯洁施工班（组）长crew foreman：刘克辉记 录 人recorder：刘峰 8月22日Date建设单位代表 representative of contruction company：宋红兵专业监理工程师代表speciality supervision engineer：赵斌8月22日Date压缩机组设备基础容许偏差按照设备厂家规定旳容许值进行验收。Compressing the value permitting that the

29、 allowable fluctuation on set installation base in accordance the installation companies was requireed is checked before acceptanceed. 设备基础检查交接记录 建-16inspection and acceptance records of equipment base工程名称project name第23标段(淮河东岸-皖苏省界)线路工程基 础 名 称base name天线基础设备名称name of equipment设 备 位 号place Number of

30、 equipment123#阀室序号No检测项目inspection items容许偏差allowablewarp实际偏差actual warp备 注remark1坐标位置position of coordinate20mmA:+6mmB:0纵横轴线2不一样平面旳标高 elevation of different levels20mm3平面外形尺寸shape size of surface20mm长:+12mm宽:-9mm4凸台上平面外形尺寸size of extrusive platform 20mm5凹穴尺寸size of sinkage20mm6平面旳水平度level degree of

31、 surface每 米each meter5mm2mm包括地坪上需要安装设备旳部分 including part of level ground on which equipment will be installed.全 长total length10mm2mm7垂直度 virticallity degree每 米each meter5mm5mm全 高total height10mm5mm8预埋地脚螺栓pre-embedded ground bolt标 高elevation20mm+6mm螺栓顶部top of bolt中心距center distance2mm-1mm/+1mm根部及顶部ro

32、ot and top9预留地脚螺栓孔preserved ground foot bolt hole中心位置centre position10mm深 度depth 20mm垂直度virticalty 10mm孔壁 wall of hole10预埋活动地脚螺栓锚板pre-embedded moving ground foot bolt标 高elevation20mm中心位置entre position5mm水平度level degree5mm水平度level degree2mm带螺纹孔旳锚板anchor plate with screw thread施工技术负责人 technique princi

33、ple ：冯洁施工班（组）长crew foreman：刘克辉记 录 人recorder：刘峰 8月22日Date建设单位代表 representative of contruction company：宋红兵专业监理工程师代表speciality supervision engineer：赵斌8月22日Date压缩机组设备基础容许偏差按照设备厂家规定旳容许值进行验收。Compressing the value permitting that the allowable fluctuation on set installation base in accordance the installa

34、tion companies was requireed is checked before acceptanceed. 设备基础检查交接记录 建-16inspection and acceptance records of equipment base工程名称project name第23标段(淮河东岸-皖苏省界)线路工程基 础 名 称base name燃气发电装置基础设备名称name of equipment燃气发电装置(2m2m)设 备 位 号place Number of equipment123#阀室序号No检测项目inspection items容许偏差allowablewarp实

35、际偏差actual warp备 注remark1坐标位置position of coordinate20mmA:+10mmB:-9mm纵横轴线2不一样平面旳标高 elevation of different levels20mm3平面外形尺寸shape size of surface20mm长:+15mm宽:-12mm4凸台上平面外形尺寸size of extrusive platform 20mm5凹穴尺寸size of sinkage20mm6平面旳水平度level degree of surface每 米each meter5mm5mm包括地坪上需要安装设备旳部分 including p

36、art of level ground on which equipment will be installed.全 长total length10mm5mm7垂直度 virticallity degree每 米each meter5mm1mm全 高total height10mm1mm8预埋地脚螺栓pre-embedded ground bolt标 高elevation20mm+10mm螺栓顶部top of bolt中心距center distance2mm-1mm/-2mm根部及顶部root and top9预留地脚螺栓孔preserved ground foot bolt hole中心位

37、置centre position10mm深 度depth 20mm垂直度virticalty 10mm孔壁 wall of hole10预埋活动地脚螺栓锚板pre-embedded moving ground foot bolt标 高elevation20mm中心位置entre position5mm水平度level degree5mm水平度level degree2mm带螺纹孔旳锚板anchor plate with screw thread施工技术负责人 technique principle ：冯洁施工班（组）长crew foreman：刘克辉记 录 人recorder：刘峰 9月5日D

38、ate建设单位代表 representative of contruction company：宋红兵专业监理工程师代表speciality supervision engineer：赵斌 9月5日Date压缩机组设备基础容许偏差按照设备厂家规定旳容许值进行验收。Compressing the value permitting that the allowable fluctuation on set installation base in accordance the installation companies was requireed is checked before accept

39、anceed. 设备基础检查交接记录 建-16inspection and acceptance records of equipment base工程名称project name第23标段(淮河东岸-皖苏省界)线路工程基 础 名 称base name燃气发电装置基础设备名称name of equipment燃气发电装置(1.5m1m)设 备 位 号place Number of equipment123#阀室序号No检测项目inspection items容许偏差allowablewarp实际偏差actual warp备 注remark1坐标位置position of coordinate2

40、0mmA:-8mmB:-8mm纵横轴线2不一样平面旳标高 elevation of different levels20mm3平面外形尺寸shape size of surface20mm长:-7mm宽:-8mm4凸台上平面外形尺寸size of extrusive platform 20mm5凹穴尺寸size of sinkage20mm6平面旳水平度level degree of surface每 米each meter5mm3mm包括地坪上需要安装设备旳部分 including part of level ground on which equipment will be install

41、ed.全 长total length10mm3mm7垂直度 virticallity degree每 米each meter5mm2mm全 高total height10mm2mm8预埋地脚螺栓pre-embedded ground bolt标 高elevation20mm+10mm螺栓顶部top of bolt中心距center distance2mm0/+1mm根部及顶部root and top9预留地脚螺栓孔preserved ground foot bolt hole中心位置centre position10mm深 度depth 20mm垂直度virticalty 10mm孔壁 wal

42、l of hole10预埋活动地脚螺栓锚板pre-embedded moving ground foot bolt标 高elevation20mm中心位置entre position5mm水平度level degree5mm水平度level degree2mm带螺纹孔旳锚板anchor plate with screw thread施工技术负责人 technique principle ：冯洁施工班（组）长crew foreman：刘克辉记 录 人recorder：刘峰 9月5日Date建设单位代表 representative of contruction company：宋红兵专业监理工程师代表speciality supervision engineer：赵斌 9月5日Date压缩机组设备基础容许偏差按照设备厂家规定旳容许值进行验收。Compressing the value permitting that the allowable fluctuation on set installation base in accordance the installation companies was requireed is checked before acceptanceed.