钢筋自动下料机设计【含CAD图纸、说明书】
摘 要-I-摘 要钢筋自动下料机,是一种能够将钢筋拉直,并将钢筋切成一定长度的工程机械。机械结构分钢筋调直和钢筋切断两部分;工作时钢筋自动下料机的进给机构可以自动送入钢筋,并将钢筋拉直;当输出的钢筋达到一定长度时再由液压控制的钢筋切断机构将钢筋切断。一、校直系统的设计。通过施加高频率的周期性交变应力,使材料产生超过其弹性限度的变形,原弯曲被抵消,达到校直目的。二、切断机构的设计。当钢筋达到所需长度时,切断机构自动进行切断,切断后活动切刀回到原始位置。三、传动系统的设计。电机通过一组的 V 带、减速器、齿轮、主动辊轮和从动辊轮,达到校直钢筋的目的。四、辅助装置的设计。主要是起到辅助作用的支架和主体钢架。五、电气控制系统的设计。选用 AT89C51 型单片机控制钢筋自动下料机的自动化动作。关键词 钢筋自动下料机,辊轮调直,电气控制,液压剪切装置。Abstract-II-AbstractThe steel automatic cutting machine can straighten steel, and cut it in a certain length. Mechanical structural include steel straightening and steel cutting. The feed mechanism of the Automatic steel cutting machine can transport the steel automatically at work, and straightened the steel. When the output of steel reaches a certain length and then cut off by the reinforcement agencies controlled by the hydraulic.The first. The design of the alignment system. Through periodic alternating stress applied high frequency, produce deformation more than its elastic limit. The alternately deformation reaches a certain level, The original bending is offset, To achieve the purpose of straightening.The second. The design of the cutting off institutions. When the steel to reach the required length, cutting mechanism of automatic cut, cut back to the original position after the cutting knife.The third. The design of the transmission system. A group of V with motor, reducer, gear, driving roller and the driven roller straightening reinforced to achieve through.The fourth. The design of the assistive devices. The assistive devices include stent and the main steel frame. The fifth. The design of the electrical control system. The AT89C51 type SCM is selection to control the automatic work of the steel automatic cutting machine.keywords Steel automatic cutting machine, Roller straightening, Electrical control, Hydraulic cutting device附录-3-目 录摘 要 .IABSTRACT.II第 1 章 绪论 11.1 钢筋自动下料机的应用、现状及其前景 21.2 自动下料机的分类及特点 41.3 钢筋自动下料机的基本结构及工作原理 8第 2 章 钢筋自动下料机设计方案 122.1 传动方案比较 .122.2 设计方案确定 .122.3 总体结构示意图 .132.4 本章小结 14第 3 章 自动下料机的机构设计 153.1 传动机构的设计 153.1.1 电机的选择 .153.1.2 带传动设计 .173.1.3 双级减速器设计计算 203.1.4 齿轮传动部分的设计 483.1.5 传输轴的校核 553.1.6 传输用轴承的选用与校核 603.1.7 键的选取与校核 603.2 进给辊轮的结构设计 613.3 控制长度用直线导轨的选择及计算 623.4 切削用液压缸的选择 633.5 本章小结 68第 4 章 自动下料机辅助装置设计 694.1 用于防止进给时钢筋下落用支架设计 694.2 自动下料机整体机架的结构设计 704.3 本章小结 70第 5 章 电气控制部分设计 715.1 单片机控制示意图设计 715.2 单片机控制程序设计 715.3 控制部分原理及电气元件安装位置 735.4 本章小结 73结 论 74Abstract-4-本课题研究的内容总结 74参考文献 75谢 辞 77附 录 78
收藏
编号:538412
类型:共享资源
大小:2.80MB
格式:ZIP
上传时间:2019-04-09
50
积分
- 关 键 词:
-
钢筋
自动
下料机
设计
cad
图纸
说明书
仿单
- 资源描述:
-
展开阅读全文
- 温馨提示:
1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 装配图网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
装配图网所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。