CTSO-C211 探测与避让(DAA)系统
CTSO-C211 探测与避让(DAA)系统,CTSO-C211,探测与避让(DAA)系统,ctso,c211,探测,避让,躲避,daa,系统
编 号 CTSO C211 日 期 2019 年 4 月 29 日 局长授权 批 准 中国民用航空技术标准规定 1 本技术标准规定根据中国民用航空规章 民用航空材料 零部件和机载设备技术 标准规定 CCAR37 颁发 中国民用航空技术标准规定是对用于民用航空器上的 某些航空材料 零部件和机载设备接受适航审查时 必须遵守的准则 探测与避让 DAA 系统 1 目的 本技术标准规定 CTSO 适用于为探测与避让 DAA 系统申 请技术标准规定项目批准书 CTSOA 的制造人 本 CTSO 规定了 探测与避让 DAA 系统为获得批准和使用适用的 CTSO 标记进行 标识所必须满足的最低性能标准 2 适用范围 本 CTSO 适用于自其生效之日起提交的申请 按本 CTSO 批准的 设备 其设计大改应按 CCAR 21 R4 第 21 353 条要求重新申请 CTSOA 3 要求 在本 CTSO生效之日或生效之后制造并欲使用本 CTSO标记进行 标识的探测与避让 DAA 系统 应满足 RTCA DO 365 探测及避 让系统的最低性能标准 2017 5 31 以适用于表 1 列出的功能设备 CAAC CTSO C211 2 类别及本 CTSO 第 3 h 节要求 本 CTSO 设备分类取决于系统提供的 功能 1 类是基本的 DAA 系统 2 类是带有交通警戒及防撞系统 TCAS II 7 1 版 功能 但不带有交通咨询的基本 DAA 系统 每种类型进一步细分为具有相应功能的独立部件 表 1 提供了功能设 备类别的详细信息 表 1 DAA 设备类别及产品 类 别 设备 1 危险程度 DAA 设备设 计 2 3 DAA 设备 名称 功能 功能丧失 误导性信息 1 基本 型 DAA 重大的 重大的 A 主动监视 空中交通控制雷达 信标系统 S 模式入 侵探测 TCAS II 模 式数据 避撞协调 数据 B 无人驾驶 飞机 UA DAA 处理 器 轨迹处理 DAA 警 戒 2 及导引 2 C 控制站 CS DAA 处理器 DAA 警戒 2 及导引 2 D CS DAA 控制面板 DAA 模式控制 E CS DAA 交通显示 交通 告警及导引 信息显示 2 带有 TCAS II 型 DAA 重大的 危险的 非 常重大的 见 3 6 2 b A TCAS II 7 1 版 ATCRBS S 模式入 侵探测 TCAS II 决 断咨询状态及协调 数据 避撞系统逻 辑 混合监视 B UA DAA 处理器 轨迹处理 DAA 警 戒 2 及导引 2 C CS DAA 处理器 集成 TCAS II 的 DAA 警戒 2 及导引 2 D CS DAA 控制面板 集成 TCAS II 的 DAA 模式控制 CAAC CTSO C211 3 类 别 设备 1 危险程度 DAA 设备设 计 2 3 DAA 设备 名称 功能 功能丧失 误导性信息 E CS DAA 交通显示 交通 警戒 导引 及 RA 信息显示 注 1 除了表 1 种列出的部件 为使 DAA 系统满足本 CTSO 功能要 求 1 类及 2 类设备均需要集成于交通监视的空对空雷达 ATAR 以探测非协作飞机 并集成于自动相关监视广播 ADS B 接收系统 以接收 ADS B 信息 CTSO C212 提供了 ATAR 设备最低性能标准 CTSO C166b 提供了 DAA 系统的 ADS B 接收设备最低性能标准 DAA 系统使用的 CTSO C166b 设备必须为 A 级设备 且具备接受 1090MHz 的能力 除了 CTSO C166b 的 A 级设备外 DAA 系统还可 能采用 CTSO C154c 设备 然而 由于 CTSO C154c 设备本身不满足 DAA 系统中 ADS B 探测性能需求 因此 CTSO C154c 设备可能无法 替代 CTSO C166b 的 A 级设备 2 设备既可以被定为类别 1 的设备 也可以被定为类别 2 的设备 设备 A B 均安装于飞机 如果设备 C D 及 E 包含用于地面远程运 行或 CS 的功能 或包含用于载人飞机的功能 则这些部件可安装于 飞机上 设备 B 和 C 包含 DAA 警戒及导引功能 可在无人飞机系统 平台上互换 这些功能可能驻留于 UA或 CS中 相应安装限制见 5 a 3 节 3 对于单独设备的要求 详见 RTCA DO 365 附录 O a 功能 本 CTSO 的标准适用于采用仪表飞行规则 IFR 来提供交通警 CAAC CTSO C211 4 戒和导引功能以保持 DAA 足够清晰的 DAA 1 类及 2 类设备 此外 DAA系统 2类设备包括集成于不带交通咨询功能的 TCAS II系统 7 1 版 的 RA 能力 注 DAA 足够清晰是指飞机周围的时间和 或空间边界清晰 以 防止交通冲突 定量定义见 RTCA DO 365 附录 C b 失效状态类别 1 本 CTSO 第 3 a 节定义的功能丧失会导致重大的失效状态 2 造成误导信息的功能失效包括如下 i 1 类及 2 类 功能异常导致的重大失效状态会造成 DAA 警戒 和 或导引误导 ii 2 类 未通告失效状态导致的危险的 特别重大的失效状态可 能会导致 TCAS II 的 RA 功能错误或丧失 iii 设备的设计保证等级应至少与这种失效状态类别相对应 c 功能鉴定 应按 RTCA DO 365 第 2 4 节中试验条件 证明设备性能满足要 求 d 环境鉴定 应按 RTCA DO 365 第 2 3 节中标准的环境条件及实验程序 证 明机载及地面设备性能满足要求 申请人可采用除 RTCA DO 365 第 2 3 节 RTCA DO 160G 机载及地面设备 MIL STD 810G MIL STD 704 及 RTCA DO 365 附录 J 地面设备 以外其它适用于 机载或地面设备的标准环境条件和试验程序 证明设备满足最低性能 CAAC CTSO C211 5 标准要求的性能 注 通常情况下 RTCA DO 160D 包括 Change 1 和 Change 2 或早期版本不再适用 如果使用该版本则需按照本 CTSO 第 3 g 节中 的偏离要求进行证明 e 软件鉴定 如果设备包含软件 则软件应按照 RTCA DO 178B 机载系统和 设备合格审定中的软件考虑 1992 12 1 或 RTCA DO 178C 机载 系统和设备合格审定中的软件考虑 2011 12 13 的要求进行研制 软件的设计保证等级应与本 CTSO 第 3 b 节规定的失效状态类别一 致 f 电子硬件鉴定 如果设备中包含复杂电子硬件 则应按照 RTCA DO 254 机载 电子硬件设计保证指南 2000 4 19 的要求进行研制 硬件的设计 保证等级应与本 CTSO 第 3 b 节规定的失效状态类别一致 对于确定 为简单的机载电子硬件 可按 RTCA DO 254 中第 1 6 节的要求处理 g 偏离 如果采用替代或等效的符合性方法来满足本 CTSO 规定的最低 性能标准要求 则申请人必须表明设备保持了等效的安全水平 申请 人应按照 CCAR 21 R4 第 21 368 条 一 要求申请偏离 h 机载数据记录能力 除了 RTCA DO 365 第 2 2 2 2 4 的性能要求 UA DDA 处理器应 记录与入侵相关的目标源 如雷达 ADS B 和 或主动监视 该入侵 CAAC CTSO C211 6 能够触发导引信息警戒 或导致 DAA 纠正警戒 DAA 告警或 TCAS II RA 4 标记 a 至少应为一个主要部件设置永久清晰的标记 标记应包括 CCAR 21 R4 第 21 423 条 二 规定的所有信息 并包括设备类型及 部件名称 除非已在安装说明中标识或能够通过软件识别 b 如果设备中包含软件和 或机载电子硬件 则件号必须能够表 明软件和硬件的构型 件号编排时 在件号中可为硬件 软件和机载 电子硬件各划分一个单独区域 d 可以使用电子标记标识软件和机载电子硬件 此标记可通过 软件写入硬件部件内部 而不用将其标识在设备铭牌中 如果使用电 子标记 则其必须容易读取 无需使用特殊工具或设备 5 申请资料要求 申请人必须向负责该项目审查的人员提交相关技术资料以支持 设计和生产批准 提交资料包括 CCAR 21 R4 第 21 353 条 一 1 规定的符合性声明和以下资料副本 a 手册 包含以下内容 1 运行说明和设备限制 该内容应对设备运行能力进行充 分描述 注 RTCA DO 365 允许一些功能驻留于 CS 地面 或机载设 备中 因此 必须能够清晰识别主要驻留功能 的运行说明及部件限制 以保证 DAA 设备的能力满足本 CTSO 要求 CAAC CTSO C211 7 2 对所有偏离的详细描述 3 安装程序和限制 必须 确保按照此安装程序安装设备后 设备仍符合本 CTSO 的要求 限制必须确定任何特殊的安装要求 包 括但不限于 1 安装 1 类或 2 类 以及 UA 或地面 CS 应用 2 对 于驻留在 UA 或 CS 中的 DAA 警戒和 或 DAA 导引功能 如表 1 注 释 2 所示 识别部件是否提供了这些功能 3 可互换部件 UA 或 CS 应具备安装兼容性要求 以确保能够提供表 1 中 DAA 系统 1 类 或 2 类设备的功能 4 对于既可以定为 1 类又可以定为 2 类的设备 应识别给定安装批准的配置类型适用性 安装限制还必须以注释的方 式包含以下声明 本设备满足技术标准规定中要求的最低性能标准 如欲安装此 设备 必须获得单独的安装批准 4 对于所有软件和机载电子硬件构型 包括如下内容 i 软件件号 包括版本和设计保证等级 ii 机载电子硬件件号 包括版本和设计保证等级 iii 功能描述 5 设备中每个部件进行环境鉴定的试验条件总结 例如 可采用 RTCA DO 160G 机载设备环境条件和试验程序 附录 A 的 表格方式描述 6 原理图 布线图 以及设备安装所必需的其它文件 7 设备的可更换部件清单 注明件号 如适用 包括对供 应商件号的交叉索引 CAAC CTSO C211 8 b 持续适航文件 包含设备周 期性维护 校准及修理要求 以 保证设备的持续适航性 如适用 应包括建议的检查间隔和使用寿命 c 如果设备包含软件 则还应提供 软件合格审定计划 PSAC 软件构型索引和软件完结综述 d 如果设备包含简单的或复杂 电子硬件 还应提供 硬件合格 审定计划 PHAC 硬件验证计划 顶层图纸和硬件完结综述 或 相似文件 如适用 e 铭牌图纸 规定设备如何标识本 CTSO 中第 4 节所要求的标 记信息 f 确定设备中所包含而未按照本 CTSO第 3节进行评估的功能或 性能 即 非 CTSO 功能 在获得 CTSOA 的同时非 CTSO 功能也 一同被接受 接受这些非 CTSO 功能 申请人必须声明这些功能 并 在 CTSO 申请时提供以下信息 1 非 CTSO 功能的描述 如性能规范 失效状态类别 软 件 硬件以及环境鉴定类别 还应包括一份确认非 CTSO 功能不会影 响设备对本 CTSO 第 3 节要求符合性的声明 2 安装程序和限制 能够确保非 CTSO 功能满足第 5 f 1 节所声明的功能和性能规范 3 第 5 f 1 节所描述非 CTSO 功能的持续适航要求 4 接口要求和相关安装试验程序 以确保对第 5 f 1 节性 能资料要求的符合性 5 如适用 试验大纲 试验分析和试验结果 以验证 CTSO CAAC CTSO C211 9 设备的性能不会受到非 CTSO 功能的影响 6 如适用 试验大纲 试验分析和试验结果 以验证第 5 f 1 节描述的非 CTSO 功能的功能和性能 g 按 CCAR 21 R4 第 21 358 条要求提供质量系统方面的说明资 料 包括功能试验规范 质量系统应确保检测到可能会对 CTSO 最低 性能标准符合性有不利影响的任何更 改 并相应地拒收该产品 h 按 CCAR 21 R4 第 21 355 条要求提供机构方面的说明文件 i 材料和工艺规范清单 j 定义设备设计的图纸和工艺清单 包括修订版次 k 制造人的 CTSO 鉴定报告 表明按本 CTSO 第 3 c 节完成的试 验结果 6 制造人资料要求 除直接提交给局方的资料外 还应准备如下技术资料供局方评 审 a 用来鉴定每件设备是否符合本 CTSO 要求的功能鉴定规范 b 设备校准程序 c 原理图 d 布线图 e 材料和工艺规范 f 按本 CTSO 第 3 d 节要求进行的环境鉴定试验结果 g 如果设备包含软件 提供 RTCA DO 178B 或 RTCA DO 178C 中规定的相关文档 包括所有支持 RTCA DO 178B 或 RTCA DO 178C CAAC CTSO C211 10 附件 A 软件等级的过程目标和输出 中适用目标的资料 h 如果设备包含复杂电子硬件 应提供 RTCA DO 254 附录 A 表 A 1 中定义的与设计保证等级和硬件生命周期相关的资料 对于简单 电子硬件 应提供以下资料 测试用例或程序 测试结果 测试覆盖 率分析 工具评估和鉴定资料 构型 管理记录并包含问题报告 i 如果设备包含非 CTSO 功能 必须提供第 6 a 节至第 6 h 节与 非 CTSO 功能相关的资料 7 随设备提交给用户的资料要求 a 如欲向一个机构 例如运营人或 修理站 提交一件或多件按 本 CTSO 制造的设备 则应随设备提供本 CTSO 第 5 a 节和 5 b 节的 资料副本 以及设备正确安装 审定 使用和持续适航所必需的资料 b 如果设备包含已声明的非 CTSO 功能 则还应包括第 5 f 1 节至第 5 f 4 节所规定资料的副本 c 如果设备包含软件 为型号审定 补充型号审定或申请人提 供开口问题报告总结 以支持本 CTSO 的安装批准 8 引用文件 a RTCA 文件可从以下地址订购 Radio Technical Commission for Aeronautics Inc 1150 18th Street NW Suite 910 Washington D C 20036 也可通过网站 www rtca org 订购副本 b MIL STD 文件可从以下地址订购 DLA Document Services Building 4 D CAAC CTSO C211 11 700 Robbins Avenue Philadelphia PA 19111 5094 也可通过网站 quicksearch dla mil 订购副本 English Translation Version for Reference Only Number CTSO C211 Date of approval Apr 29 2019 Approved by Xu Chaoqun China Civil Aviation Technical Standard Order 1 This China Civil Aviation Technical Standard Order CTSO is issued according to Part 37 of the China Civil Aviation Regulations CCAR 37 Each CTSO is a criterion which the concerned aeronautical materials parts or appliances used on civil aircraft must comply with when it is presented for airworthiness certification Detect and Avoid DAA Systems 1 Purpose This China Civil Aviation Technical Standard Order CTSO is for manufacturers applying for a Detect and Avoid DAA Systems CTSO authorization CTSOA This CTSO prescribes the minimum performance standards MPS that Detect and Avoid DAA Systems must first meet for approval and identification with the applicable CTSO marking 2 Applicability This CTSO affects new application submitted after its effective date Major design changes to article approved under this CTSO will require a new authorization in accordance with section 21 353 of CCAR 21 R4 3 Requirements New models of DAA equipment identified and manufactured on or English Translation Version for Reference Only CAAC CTSO C211 2 after the effective date of this CTSO must meet the MPS qualification and documentation requirements in Section 2 of RTCA Document No RTCA DO 365 Minimum Operational Performance Standards for Detect and Avoid Systems dated May 31 2017 as appropriate to the functional equipment classes listed in Table 1 and paragraph 3 h The different classes for this CTSO are defined by the different functionalities the system provides Class 1 is the basic DAA system and Class 2 is the basic DAA system with Traffic Alert and Collision Avoidance System TCAS II Version 7 1 functions except for traffic advisories Each class is further subdivided into several individual articles with corresponding functionalities Table 1 provides details of the functional equipment classes and articles Table 1 DAA Classes and Articles class Equipment 1 criticality DAA Article Designation 2 b Airborne electronic hardware part number including revision and design assurance level c Functional description 5 A summary of the test conditions used for environmental qualifications for each component of the article For example a form as described in RTCA DO 160G Environmental Conditions and Test Procedures for Airborne Equipment Appendix A 6 Schematic drawings wiring diagrams and any other documentation necessary for installation of the HUD English Translation Version for Reference Only CAAC CTSO C211 10 7 List of replaceable components by part number that makes up the Class 1 DAA or Class 2 DAA equipment Include vendor part number cross references when applicable b Instructions covering periodic maintenance calibration and repair to ensure that the DAA continues to meet the CTSO approved design Include recommended inspection intervals and service life as appropriate c If the article includes software a plan for software aspects of certification PSAC software configuration index and software accomplishment summary d If the article includes simple or complex custom airborne electronic hardware a plan for hardware aspects of certification PHAC hardware verification plan top level drawing and hardware accomplishment summary or similar document as applicable e A drawing depicting how the article will be marked with the information required by paragraph 4 of this CTSO f Identify functionality contained in the article not evaluated under paragraph 3 of this CTSO that is non CTSO functions Non CTSO functions are accepted in parallel with the CTSO authorization For those non CTSO functions to be accepted the applicant must declare these functions and include the following information with the CTSO application English Translation Version for Reference Only CAAC CTSO C211 11 1 Description of the non CTSO function s such as performance specifications failure condition classifications software hardware and environmental qualification levels Include a statement confirming that the non CTSO function s do not interfere with the article s compliance with the requirements of paragraph 3 2 Installation procedures and limitations sufficient to ensure that the non CTSO function s meets the declared functions and performance specification s described in paragraph 5 f 1 3 Instructions for continued performance applicable to the non CTSO function s described in paragraph 5 f 1 4 Interface requirements and applicable installation test procedures to ensure compliance with the performance data defined in paragraph 5 f 1 5 Test plans and analysis as appropriate to verify that performance of the hosting CTSO article is not affected by the non CTSO function s 6 Test plans and analysis as appropriate to verify the function and performance of the non CTSO function s as described in paragraph 5 f 1 g The quality manual required by section 21 358 of CCAR 21 R4 including functional test specifications The quality system must ensure that you will detect any change to the approved design that could English Translation Version for Reference Only CAAC CTSO C211 12 adversely affect compliance with the CTSO MPS and reject the article accordingly Applicants who currently hold CTSOAs must submit revisions to the existing quality manual as necessary h A description of your organization as required by section 21 355 of CCAR 21 R4 i Material and process specifications list j A list of all drawings and processes including revision level that define the article s design k Manufacturer s CTSO qualification report showing results of testing accomplished according to paragraph 3 c of this CTSO 6 Manufacturer Data Requirements Besides the data given directly to the authorities have the following technical data available for review by the authorities a Functional qualification specifications for qualifying each production article to ensure compliance with this CTSO b Article calibration procedures c Schematic drawings d Wiring diagrams e Material and process specifications f The results of the environmental qualification tests conducted according to paragraph 3 d of this CTSO English Translation Version for Reference Only CAAC CTSO C211 13 g If the article includes software the appropriate documentation defined in RTCA DO 178B or RTCA DO 178C specified in paragraph 3 e of this CTSO including all data supporting the applicable objectives in Annex A Process Objectives and Outputs by Software Level of RTCA DO 178B or RTCA DO 178C h If the article includes complex custom airborne electronic hardware the appropriate hardware life cycle data in combination with design assurance level as defined in RTCA DO 254 Appendix A Table A l For simple custom airborne electronic hardware the following data are required test cases or procedures test results test coverage analysis tool assessment and qualification data and configuration management records including problem reports i If the article contains non CTSO function s you must also make available items 6 a through 6 h as they pertain to the non CTSO function s 7 Furnished Data Requirements a If furnishing one or more articles manufactured under this CTSO to one entity such as an operator or repair station provide one copy of the data in paragraphs 5 a and 5 b of this CTSO Add any other data needed for the proper installation certification use or for continued compliance with the CTSO of the HUD English Translation Version for Reference Only CAAC CTSO C211 14 b If the article contains declared non CTSO function s include one copy of the data in paragraphs 5 f 1 through 5 f 4 c If the article contains software include one copy of the Open Problem Report OPR summary to type certification or supplemental type certification 8 Availability of Referenced Documents a Order SAE documents from Society of Automotive Engineers Inc 400 Commonwealth Drive WARRENDALE PA 15096 001 USA You can also order copies online at www sae org b Order RTCA documents from Radio Technical Commission for Aeronautics Inc 1150 18th Street NW Suite 910 Washington D C 20036 You can also order copies online at www rtca org
收藏
编号:11120850
类型:共享资源
大小:181.63KB
格式:RAR
上传时间:2020-04-19
10
积分
- 关 键 词:
-
CTSO-C211
探测与避让(DAA)系统
ctso
c211
探测
避让
躲避
daa
系统
- 资源描述:
-
CTSO-C211 探测与避让(DAA)系统,CTSO-C211,探测与避让(DAA)系统,ctso,c211,探测,避让,躲避,daa,系统
展开阅读全文
- 温馨提示:
1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 装配图网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
装配图网所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。