尾接杆零件的工艺规程和斜孔钻模夹具设计【含CAD图纸4张、说明书、答辩稿】
资源目录里展示的全都有,所见即所得。下载后全都有,请放心下载。原稿可自行编辑修改=【QQ:401339828 或11970985 有疑问可加】
本科毕业设计论文题 目 尾接杆零件的工艺规程和斜孔钻模设计专业名称 机械设计制造及其自动化 学生姓名 指导教师 毕业时间设计论文 毕业 任务书一、题目 尾接杆零件的工艺规程和斜孔钻模设计二、指导思想和目的要求毕业设计(论文)是培养学生自学能力、综合应用能力、独立工作能力的重要教学实践环节。 通过毕业设计,学生对四年所学知识进行回顾和总结,培养自学能能力和独立工作能力,对本专业加深了解,为步入社会工作岗位做好理论和时间准备。学会理论联系实际,用严谨和认真的态度分析和解决遇到的问题,从而实现认识的深化。三、主要技术指标1、 绘制零件图;2、 设计与绘制毛坯图3、 制定工艺路线4、 编制全部工艺规程5、 设计钻模6、 编写论文四、进度和要求1、分析并绘制零件图 1周2、绘制毛坯图 1周3、设计工艺路线及编制工艺规程 4周4、设计工艺装备 3周5、编写说明书(论文) 2周五、主要参考书及参考资料 1 阎光明,侯忠滨.现代制造工艺基础.西安:西北工业大学出版社,2007. 2 王长春,孙步功.互换性与测量技术基础.北京:北京大学出版社,2010.机械专业外语文献翻译系 别 机电工程系 专 业 机械设计制造及其自动化班 级学生姓名学 号日 期机械设计摘要: 机器是由机械装置和其它组件组成的。它是一种用来转换或传递能量的装置,例如:发动机、涡轮机、车辆、起重机、印刷机、洗衣机、照相机和摄影机等。许多原则和设计方法不但适用于机器的设计,也适用于非机器的设计。术语中的“机械装置设计” 的含义要比“机械设计”的含义更为广泛一些,机械装置设计包括机械设计。在分析运动及设计结构时,要把产品外型以及以后的保养也要考虑在机械设计中。在机械工程领域中,以及其它工程领域中,所有这些都需要机械设备,比如:开关、凸轮、阀门、船舶以及搅拌机等。关键词: 设计流程 设计规则 机械设计设计流程设计开始之前就要想到机器的实际性,现存的机器需要在耐用性、效率、重量、速度,或者成本上得到改善。新的机器必需具有以前机器所能执行的功能。在设计的初始阶段,应该允许设计人员充分发挥创造性,不要受到任何约束。即使产生了许多不切实际的想法,也会在设计的早期,即在绘制图纸之前被改正掉。只有这样,才不致于阻断创新的思路。通常,还要提出几套设计方案,然后加以比较。很有可能在这个计划最后决定中,使用了某些不在计划之内的一些设想。一般的当外型特点和组件部分的尺寸特点分析得透彻时,就可以全面的设计和分析。接着还要客观的分析机器性能的优越性,以及它的安全、重量、耐用性,并且竞争力的成本也要考虑在分析结果之内。每一个至关重要的部分要优化它的比例和尺寸,同时也要保持与其它组成部分相协调。也要选择原材料和处理原材料的方法。通过力学原理来分析和实现这些重要的特性,如那些静态反应的能量和摩擦力的最佳利用,像动力惯性、加速动力和能量;包括弹性材料的强度、应力和刚度等材料的物理特性,以及流体润滑和驱动器的流体力学。设计的过程是重复和合作的过程,无论是正式或非正式的进行,对设计者来说每个阶段都很重要。最后,以图样为设计的标准,并建立将来的模型。如果它的测试是符合事先要求的,则再将对初步设计进行某些修改,使它能够在制造成本上有所降低。产品的设计需要不断探索和发展。许多方案必须被研究、试验、完善,然后决定使用还是放弃。虽然每个工程学问题的内容是独特的,但是设计师可以按照类似的步骤来解决问题。产品的责任诉讼迫使设计人员和公司在选择材料时,采用最好的程序。在材料过程中,五个最常见的问题为:(a)不了解或者不会使用关于材料应用方面的最新最好的信息资料;(b)未能预见和考虑材料的合理用途(如有可能,设计人员还应进一步预测和考虑由于产品使用方法不当造成的后果。在近年来的许多产品责任诉讼案件中,由于错误地使用产品而受到伤害的原告控告生产厂家,并且赢得判决);(c)所使用的材料的数据不全或是有些数据不确定,尤其是当其性能数据长期不更新;(d)质量控制方法不适当和未经验证;(e)由一些完全不称职的人员选择材料。通过对上述五个问题的分析,可以得出这些问题是没有充分理由而存在的结论。对这些问题的研究分析可以为避免这些问题的出现而指明方向。尽管采用最好的材料选择方法也不能避免发生产品责任诉讼,设计人员和工业界按照适当的程序进行材料选择,可以大大减少诉讼的数量。从以上的讨论可以看出,选择材料的人们应该对材料的性质,特点和加工方法有一个全面而基本的了解。在随后生产和售后服务的几年中,要接受新观念的变化,或者由试验和经验为基础,进一步分析并改进。一些设计规则在本节中,建议要运用创造性的态度来替代和改进。也许会创造出更实用、更经济、更耐用的产品。为了激发创造性思维,下列是设计和分析的建议规则。前六个规则对设计者来说特别适用。1. 要有创造性的利用所需要的物理性质和控制过程。2. 认识负载产生的影响及其意义。3. 预测没有想到的负载。4. 创造出对载荷更为有利的条件。5. 提供良好的应力分布和最小的刚度条件。6. 运用最简单的方程来优化体积和面积。7. 选择组合材料。8. 仔细选择所备的原料和不可缺少的组件。9. 调整有效的设计方案,以适应生产过程和降低成本。10. 规定好准确的位置条件为了使组件安装时不干涉。机械设计包括一下内容:1. 对设计过程、设计所需要公式以及安全系数进行介绍。2. 回顾材料特性、静态和动态载荷分析,包括梁、振动和冲击载荷。3. 回顾应力的基本规律和失效分析。4. 介绍静态失效理论和静态载荷下机械断裂分析。5. 介绍疲劳失效理论并强调在压力条件下接近高循环的疲劳设计,这通常用在旋转机械的设计中。6. 深入探讨机械磨损机理、表面接触应力和表面疲劳现象。7. 使用疲劳分析技术校核轴的设计。8. 讨论润滑油膜与滚动轴承的理论和应用。9. 深入介绍直齿圆柱齿轮的动力学、设计和应力分析,并简单介绍斜齿轮、锥齿轮和涡轮有关方面的问题。10. 讨论弹簧设计、螺杆等紧固件的设计,包括传动螺杆和预紧固件。11. 介绍盘式和鼓式离合器以及制动器的设计和技术说明。机械设计一台完整机器的设计是一个复杂的过程。机械设计是一项创造性的工作。设计工程师不仅在工作上要有创造性,还必须在机械制图、运动学、工程材料、材料力学和机械制造工艺学等方面具有深厚的基础知识。任何产品在设计时第一步就是选择产品每个部分的构成材料。许多的材料被今天的设计师所使用。对产品的功能,它的外观、材料的成本、制造的成本作出必要的选择是十分重要的。对材料的特性必须事先作出仔细的评估。仔细精确的计算是必要的,以确保设计的有效性。在任何失败的情况下,最好知道在最初设计中有有缺陷的部件。计算(图纸尺寸)检查是非常重要的。一个小数点的位置放错,就可以导致一个本可以完成的项目失败。设计工作的各个方面都应该检查和复查。计算机是一种工具,它能够帮助机械设计师减轻繁琐的计算,并对现有数据提供进一步的分析。互动系统基于计算机的能力,已经使计算机辅助设计(CAD)和计算机辅助制造(CAM)成为了可能。心理学家经常谈论如何使人们适应他们所操作的机器。设计人员的基本职责是努力使机器来适应人们。这并不是一项容易的工作,因为实际上并不存在着一个对所有人来说都是最优的操作范围和操作过程。另一个重要问题,设计工程师必须能够同其他有关人员进行交流和磋商。在开始阶段,设计人员必须就初步设计同管理人员进行交流和磋商,并得到批准。这一般是通过口头讨论,草图和文字材料进行的。如前所诉,机械设计的目的是生产能够满足人类需求的产品。发明、发现和科技知识本身并不一定能给人类带来好处,只有当它们被应用在产品上才能产生效益。因而,应该认识到在一个特定的产品进行设计之前,必须先确定人们是否需要这种产品。应当把机械设计看成是机械设计人员运用创造性的才能进行产品设计、系统分析和制定产品的制造工艺学的一个良机。掌握工程基础知识要比熟记一些数据和公式更为重要。仅仅使用数据和公式是不足以在一个好的设计中做出所需的全部决定的。另一方面,应该认真精确的进行所有运算。例如,即使将一个小数点的位置放错,也会使正确的设计变成错误的。一个好的设计人员应该勇于提出新的想法,而且愿意承担一定的风险,当新的方法不适用时,就使用原来的方法。因此,设计人员必须要有耐心,因为 所花费的时间和努力并不能保证带来成功。一个全新的设计,要求屏弃许多陈旧的,为人们所熟知的方法。由于许多人墨守成规,这样做并不是一件容易的事。一位机械设计师应该不断地探索改进现有的产品的方法,在此过程中应该认真选择原有的、经过验证的设计原理,将其与未经过验证的新观念结合起来。新设计本身会有许多缺陷和未能预料的问题发生,只有当这些缺陷和问题被解决之后,才能体现出新产品的优越性。因此,一个性能优越的产品诞生的同时,也伴随着较高的风险。应该强调的是,如果设计本身不要求采用全新的方法,就没有必要仅仅为了变革的目的而采用新方法。外文原文Mechanical DesignAbstract:A machine is a combination of mechanisms and other components which transforms, transmits. Examples are engines, turbines, vehicles, hoists, printing presses, washing machines, and movie cameras. Many of the principles and methods of design that apply to machines also apply to manufactured articles that are not true machines. The term mechanical design is used in a broader sense than machine design to include their design. the motion and structural aspects and the provisions for retention and enclosure are considerations in mechanical design. Applications occur in the field of mechanical engineering, and in other engineering fields as well, all of which require mechanical devices, such as switches, cams, valves, vessels, and mixers.Keywords: Mechanical Design mechanisms Design ProcessThe Design ProcessDesigning starts with a need real.Existing apparatus may need improvements in durability, efficiency, weight, speed, or cost. New apparatus may be needed to perform a function previouslydone by men, such as computation, assembly, or servicing. With the objective wholly or partlyIn the design preliminary stage, should allow to design the personnel fully to display the creativity, not each kind of restraint. Even if has had many impractical ideas, also can in the design early time, namely in front of the plan blueprint is corrected. Only then, only then does not send to stops up the innovation the mentality. Usually, must propose several sets of design proposals, then perform the comparison. Has the possibility very much in the plan which finally designated, has used certain not in plan some ideas which accepts.When the general shape and a few dimensions of the several components become apparent, analysis can begin in earnest. The analysis will have as its objective satisfactory or superior performance, plus safety and durability with minimum weight, and a competitive cost. Optimum proportions and dimensions will be sought for each critically loaded section, together with a balance between the strengths of the several components. Materials and their treatment will be chosen. These important objectives can be attained only by analysis based upon the principles of mechanics, such as those of static for reaction forces and for the optimum utilization of friction; of dynamics for inertia, acceleration, and energy; of elasticity and strength of materials for stress and deflection; of physical behavior of materials; and of fluid mechanics for lubrication and hydrodynamic drives. The analyses may be made by the same engineer who conceived the arrangement of mechanisms, or, in a large company, they may be made by a separate analysis division or research group. Design is a reiterative and cooperative process, whether done formally or informally, and the analyst can contribute to phases other than his own. Product design requires much research and development. Many Concepts of an idea must be studied, tried, and then either used or discarded. Although the content of each engineering problem is unique, the designers follow the similar process to solve the problems. Product liability suits designers and forced in material selection, using the best program. In the process of material, the most common problems for five (a) dont understand or not use about the latest application materials to the best information, (b) failed to foresee and consider the reasonable use material may (such as possible, designers should further forecast and consider due to improper use products. In recent years, many products liability in litigation, the use of products and hurt the plaintiff accused manufacturer, and won the decision), (c) of the materials used all or some of the data, data, especially when the uncertainty long-term performance data is so, (d) quality control method is not suitable and unproven, (e) by some completely incompetent persons choose materials.Through to the above five questions analysis, may obtain these questions is does not have the sufficient reason existence the conclusion. May for avoid these questions to these questions research analyses the appearance indicating the direction. Although uses the best choice of material method not to be able to avoid having the product responsibility lawsuit, designs the personnel and the industry carries on the choice of material according to the suitable procedure, may greatly reduce the lawsuit the quantity. May see from the above discussion, the choice material people should to the material nature, the characteristic and the processing method have comprehensive and the basic understanding. Finally, a design based upon function, and a prototype may be built. If its tests are satisfactory, the initial design will undergo certain modifications that enable it to be manufactured in quantity at a lower cost. During subsequent years of manufacture and service, the design is likely to undergo changes as new ideas are conceived or as further analyses based upon tests and experience indicate alterations. Sales appeal.Some Rules for DesignIn this section it is suggested that, applied with a creative attitude, analyses can lead to important improvements and to the conception and perfection of alternate, perhaps more functional, economical,and durable products. To stimulate creative thought, the following rules are suggested for the designer and analyst. The first six rules are particularly applicable for the analyst.1. A creative use of need of physical properties and control process.2. Recognize functional loads and their significance.3. Anticipate unintentional loads.4. Devise more favorable loading conditions.5. Provide for favorable stress distribution and stiffness with minimum weight.6. Use basic equations to proportion and optimize dimensions.7. Choose materials for a combination of properties.8. Select carefully, stock and integral components.9. Modify a functional design to fit the manufacturing process and reduce cost.10. Provide for accurate location and noninterference of parts in assembly. Machinery design covers the following contents.1. Provides an introduction to the design process , problem formulation ,safety factors.2. Reviews the material properties and static and dynamic loading analysis ,Including beam , vibration and impact loading. 3. Reviews the fundamentals of stress and defection analysis. 4. Introduces fatigue-failure theory with the emphasis on stress-life approaches to high-cycle fatigue design, which is commonly used in the design of rotation machinery. 5. Discusses thoroughly the phenomena of wear mechanisms, surface contact stresses ,and surface fatigue. 6. Investigates shaft design using the fatigue-analysis techniques. 7. Discusses fluid-film and rolling-element bearing theory and application 8. Gives a thorough introduction to the kinematics, design and stress analysis of spur gears , and a simple introduction to helical ,bevel ,and worm gearing. 9. Discusses spring design including compression ,extension and torsion springs. 10. Deals with screws and fasteners including power screw and preload fasteners. 11. Introduces the design and specification of disk and drum clutches and brakes.Machine DesignThe complete design of a machine is a complex process. The machine design is a creative work. Project engineer not only must have the creativity in the work, but also must in aspect and so on mechanical drawing, kinematics, engineerig material, materials mechanics and machine manufacture technology has the deep elementary knowledge. One of the first steps in the design of any product is to select the material from which each part is to be made. Numerous materials are available to todays designers. The function of the product, its appearance, the cost of the material, and the cost of fabrication are important in making a selection. A careful evaluation of the properties of a. material must be made prior to any calculations. Careful calculations are necessary to ensure the validity of a design. In case of any part failures, it is desirable to know what was done in originally designing the defective components. The checking of calculations (and drawing dimensions) is of utmost importance. The misplacement of one decimal point can ruin an otherwise acceptable project. All aspects of design work should be checked and rechecked. The computer is a tool helpful to mechanical designers to lighten tedious calculations, and provide extended analysis of available data. Interactive systems, based on computer capabilities, have made possible the concepts of computer aided design (CAD) and computer-aided manufacturing (CAM). How does the psychologist frequently discuss causes the machine which the people adapts them to operate. Designs personnels basic responsibility is diligently causes the machine to adapt the people. This certainly is not an easy work, because certainly does not have to all people to say in fact all is the most superior operating area and the operating process. Another important question, project engineer must be able to carry on the exchange and the consultation with other concerned personnel. In the initial stage, designs the personnel to have to carry on the exchange and the consultation on the preliminary design with the administrative personnel, and is approved. This generally is through the oral discussion, the schematic diagram and the writing material carries on. If front sues, the machine design goal is the production can meet the human need the product. The invention, the discovery and technical knowledge itself certainly not necessarily can bring the advantage to the humanity, only has when they are applied can produce on the product the benefit. Thus, should realize to carries on before the design in a specific product, must first determine whether the people do need this kind of productMust regard as the machine design is the machine design personnel carries on using creative ability the product design, the system analysis and a formulation product manufacture technology good opportunity. Grasps the project elementary knowledge to have to memorize some data and the formula is more important than. The merely service data and the formula is insufficient to the completely decision which makes in a good design needs. On the other hand, should be earnest precisely carries on all operations. For example, even if places wrong a decimal point position, also can cause the correct design to turn wrongly.A good design personnel should dare to propose the new idea, moreover is willing to undertake the certain risk, when the new method is not suitable, use original method. Therefore, designs the personnel to have to have to have the patience, because spends the time and the endeavor certainly cannot guarantee brings successfully. A brand-new design, the request screen abandons obsoletely many, knows very well the method for the people. Because many person of conservativeness, does this certainly is not an easy matter. A mechanical designer should unceasingly explore the improvement existing product the method, should earnestly choose originally, the process confirmation principle of design in this process, with has not unified it after the confirmation new idea. 工 序 目 录产 品 型 号ZL - 9共 3 页零 组 件 号ZL-20-31B/30A第 1 页工序号工 序 名 称设 备工序卡片数附 注5锻造毛坯10去分模毛边钳工台115划线钳工台120车外圆C620125打顶尖孔C620130车外圆C6201从工序30起按防锈与封存说明书进行油封35钻孔1K36140镗孔C620145铣平面6H12150车球体C620155去毛刺钳工台160铰孔Z5125A165铣斜面6H13170去毛刺钳工台175铣凸R6H82180铣平面6H13185去毛刺钳工台190镗孔C6201工 序 目 录产 品 型 号ZL - 9共 3 页零 组 件 号ZL-20-31B/30A第 2 页工序号工 序 名 称设 备工序卡片数附 注95热处理1100打氧化皮C6201105研磨倒角C6201110磨外圆31511115去毛刺C6201120钻孔CH12A1125铣槽6H111130去顶尖孔C6201135车球体C6201140去毛刺钳工台1145镗孔2A7161150精镗孔2A7161155去毛刺钳工台1160攻螺纹CH12A1165磁力探伤1170检验检验台1175研磨孔研磨头1180表面处理1 工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiA去分模边10设 备钳工台定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具去外圆H段分模毛边工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiA划线15设 备钳工台定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiA车外圆20设 备C620定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具三爪卡盘尖边倒圆R0.10.5端面A按划线加工工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiA打顶尖孔25设 备C620定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具三爪卡盘中心钻A3尖边倒圆R0.10.5工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiA车外圆30设 备C620定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具 软三爪专用刀具量规尖边倒圆R0.10.5工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiA钻孔35设 备1K36定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具三爪卡盘钻头26量规工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiA镗孔40设 备C620定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具 软三爪量规2D加工前找正外圆A的跳动不大于0.1尖边倒圆R0.10.5工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiA铣平面45设 备6H12定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具三爪卡盘专用刀具工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiA车球体50设 备C620定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具专用夹具三爪卡盘工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiA去毛刺55设 备钳工台定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具去A、B表面毛刺工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiA钻铰孔60设 备Z5125A定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具专用夹具钻头25量规钻头30.2去钻、铰孔后的毛刺工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiA铣斜面65设 备6H13定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具专用夹具立铣刀3255R10铣两斜面要求R10和直径25外圆相接,不允许铣伤直径25外圆工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiA去毛刺70设 备钳工台定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具去毛刺尖边倒圆R0.10.5修锉R10和25外圆两斜面圆滑相接工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiA铣凸R75设 备6H82厂定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具专用夹具专用刀具工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiA铣平面80设 备6H13定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具专用夹具专用刀具铣后和A表面平齐工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiA去毛刺85设 备钳工台定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具专用刀具去表面A的毛刺,并修锉表面A两次加工接痕尖边倒圆R0.10.5打零件编号工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiA镗孔90设 备C620定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具 软三爪专用刀具塞规专用夹具加工前找正外圆A的跳动不大于0.1工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiAHRC36-41热处理95设 备定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具热处理HRC3641直径35.7外圆对中心的跳动不大于0.1打磨量不大于0.1零件吹砂工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiAHRC36-41打氧化皮100设 备C620定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具 软三爪砂布专用夹具加工前找正外圆A的跳动不大于0.1清理内孔和倒角的赃物和氧化皮修正倒角60工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiA研磨倒角105设 备C620定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具专用夹具专用刀具工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiA磨外圆110设 备3151定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具专用夹具卡规端面B磨不大于0.1端面B、K、E对顶尖孔的跳动不大于0.01工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiAHRC36-41 去毛刺115设 备C620定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiAHRC36-41钻孔120设 备CH12A定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具专用夹具钻头2量规去钻孔毛刺工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiAHRC36-41铣槽125设 备6H11定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具专用夹具专用刀具槽量规注意铣槽方向工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiAHRC36-41去顶尖孔130设 备C620定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具三爪卡盘注意不许夹伤外圆工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiAHRC36-41车球体135设 备C620定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具 软三爪量规专用夹具加工前找正外圆A的跳动不大于0.1工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiAHRC36-41去毛刺140设 备钳工台定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具去铣槽和车球体后的毛刺尖边倒圆R0.10.5工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiAHRC36-41镗孔145设 备2A716定 位 夹 紧 共 1 页第 1 页 序 号加 工 要 求 说 明夹 具刀 具量 具专用夹具专用刀具量规允许和工序150合并加工工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiAHRC36-41精镗孔150设 备2A716定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具专用夹具专用刀具量环工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiAHRC36-41去毛刺155设 备钳工台定 位 夹 紧 共 1 页第 1 页 序 号加 工 要 求 说 明夹 具刀 具量 具去零件外形全部毛刺,并打磨外表面尖边倒圆R0.10.5工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiAHRC36-41攻螺纹160设 备CH12A定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具专用夹具钻头2、5、10量规丝锥M6-6H螺纹倒角120度至丝底,去钻孔毛刺工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiAHRC36-41磁力探伤165设 备定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具原材料为无发纹钢工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiAHRC36-41检验170设 备定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具外观检查量规尺寸检查:塞规样板卡规塞规卡规量规槽量规卡板形位检查工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiAHRC36-41研磨孔175设 备研磨头定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具专用夹具专用刀具量规 绸布按关节轴承,UC17KU的实际尺寸研磨直径32的孔保证过盈0.010.024在轴承上用电笔写和零件相同的编号工 序 卡 片零 件 名 称材 料硬 度工序名称工 序 号尾接杆30GrMnSiAHRC36-41表面处理180设 备定 位 夹 紧 共 1 页第 1 页序 号加 工 要 求 说 明夹 具刀 具量 具外表面镀镉层厚58微米除A表面外螺纹M66H和其余内表面发兰
收藏