模具工作英文

《模具工作英文》由会员分享，可在线阅读，更多相关《模具工作英文（17页珍藏版）》请在装配图网上搜索。

1、常用朮語中英文對照short shot缺膠break斷裂flash披鋒gap toolarge after assembly裝配間隙大dimension NG尺寸NG failed toassembked不能裝配no conduct due to broken wire銅絲線斷,不導電 力度不良defective force distortion變形poor plating電鍍不良damage破損returned by production line生產線退貨wire comeoff端子松脫printing defect tapping defect打印不良,滑絲hurt批傷Crack爆裂br

2、uise碰傷broken snap斷扣Rust生銹Reworked bysupplier供應商返工Hurt on wire線披傷Holes有針孔Scratch划傷Foreign material異物Dust灰塵Cable come off線脫落Press hurt壓傷Which caused the abnormal voice from assembly造成裝配有異音Broken pins扞腳斷Lead wire導線Motor馬達It cannot rotate smoothly轉動不暢Loose gear齒輪松Lead wire導線Loose tube and bad insertion

3、wire線頭熱熔膠管脫落Panel按健表板Key defect按健不良Fold皺折Structure different with sample結构與樣板不符Brokentab柱子斷Lead wire assy導線組Adaptor火牛Black specks黑點Hole blocked up塞孔Crack破裂Mixed color料花Spec標准Actual實測Spring彈弓Nonhomogeneouse colour混色Hole larger孔徑大There are oil on the part surface部品表面有油Gear dent齒輪位碰傷Thickness NG厚度NG E-

4、PIN too high頂針位高Higher gate水口位高Colourdifferent異色Contamination雜物Grease油污Cosmetic defects熔膠不良Rusting銹斑Resilience NG彈力NG Smudge污跡Without chamfer未倒角Wire is broken線斷White plastie of terminal peal off白膠脫落Wire is broken線破損Broken snap扣位斷Loose connector線頭松脫 焊線脫落The welded wire loose The boss is shorter柱子低Odd

5、ment碎屑Rand pick選別 游標卡尺/Vemier Caliper ( VC)電子卡尺/Digital Caliper( DC)三座標測量儀(三次元)/Coordinate Measuring電子千分尺/Digital Micrometer( DM)游標千分尺/Vernier Micrometer(VM)針規/Pin Gauge( PG)投影儀/Projector( P)電子高度尺/Digital Height Gauge( DH)游標高度尺/ Vemier Height Gauge( VH)塞尺/Thickness Gauge( TG)直尺/Ruler( R)百分表/Dial Ind

6、icator( DI)涂層厚度計/Coating ThicknessGauge( CT)塊規/Block Gauge( BG)角度規(尺)/Goniometer/Bevel Protracter( G)直角尺/Right Angle Ruler/Spuare( AR)溫適度計表/Hygrothermograph( H)平台板/Flat/Plate( F)色差儀/Chromometer( C)鈕具表/Torfque Gauge( TE)推拉力計/Pull-Push Gauge( PP)數字鈕鉅儀/Digital Torfque Gauge( DT)電子稱/Digital Scale( DS)法碼

7、/Weights( WT)天平/Balance( BG)照度計/LightMeter( LM)萬用表/Multimeter(M)螺紋規/Thread Gauge( TD)表面粗糙度樣塊/Roughness Block( RB)功力表/Power Meter( PM)硬度計/Sclerometer( S)秒表/Stop Watch( SW)刀口尺/Knife Gauge( KG)放大鏡/Amlifer( A)水平儀/Level Balance ( LB)內徑千分尺/Internal Micrometer( IM)卷尺/Roll Meter( RM)耐壓測試儀器/Pressure Meter( P

8、M)千分尺/Micrometer( M)內側千分尺/Insiele Micrometer( IM)深度千分尺/Depth Micrometer( DM)其他要求(1) presentation of electrodes (2)dimension report (3)placket texture approval1。电极的介绍2，尺寸(数据)报告，3，placket咬花的承认(书)2.injection(3)submarine (4)with slides3，浇口4，有滑块3.hot runner热流道(1)hydraulic in mould (2)triggers and nail (3

9、)retrogression bolt 1， 模具里面的(液压缸)2，触发器和 契钉3，后退螺栓5.injection typeMaching(CMM)注射类型(1)conventional (2)gas (3)two-shot (4)secuencial1，一般的2，气辅的？双螺杆射出？28、模具述语入水：gate进入位：gate location水口形式：gate type大水口：edgegate细水口：pin-point gate水口大小：gate size转水口：switchingrunner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot run

10、ner,hot manifold热嘴冷流道: hotsprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/halfrunner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针:thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接

11、头：jiffy quick connector plug/socker四、模具零件：mold components三板模：3-plate mold二板模：2-platemold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejectorretainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin

12、司筒：ejector sleeve司筒针：ejector pin推板：stripperplate缩呵：movable core,return core core puller扣机(尼龙拉勾) ：nylonlatch lock斜顶：lifter模胚(架) ：mold base上内模：cavity insert下内模：core insert行位(滑块) ：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate水口气孔(edge porosity)变形(bending,warping)飞边(flash)污点(stained casting)水

13、纹(waves andlakes)拉伤(drags)顶伤(deformation from ejector pins)喷雾过量(excessive flux)冲蚀(erosion,caviation)起泡(outgassing)撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locatingring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle

14、弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowelpin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：anglefrom pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：leverarm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting

15、 line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interfereswithejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步(正

16、式)模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极)：copper electrode表面缺陷(surface defects)层妆组织(laminations)内部气孔(gas porosity)表面气泡(blisters)流动不良引起的气孔(flow

17、 porosity)缩孔(shrink porosity)热裂(heat sinks)渗漏(leakers)裂缝(cracks)杂质(inclusions)粘料(solder)积碳(carbonbuildup)32、冲模dies (stamping and punching dies)1.1单工序模single operation dies1.2复合模compound dies1.3级进模progressive dies1.4无导向模opening dies1.5导板冲模guide plate dies1.6导柱模guide pillar dies1.7通用模universal dies1.8

18、专用模dies for special purpose1.9自动模automatic dies1.10组合冲模combined dies1.11简易模low-cost dies1.11.1橡胶冲模rubber-dies1.11.2钢带模steel rule dies1.11.3低熔点合金模low-melting point alloys dies1.11.4锌基合金模zinc based dies1.11.5薄板模laminated dies1.12冲裁模blanking dies1.12.11.12.21.12.31.12.41.12.51.12.61.12.7落料模冲孔模切边模切口模切舌模

19、剖切模整修模精冲模切断模blanking diespiercing diestrimming diesnotching dieslancing diesparting diesshaving dies fineblanking diescutting-off dies1.12.81.12.91.13弯曲模bending dies1.13.1卷边模curling dies1.13.2扭曲模twisting dies1.14拉伸模drawing dies1.14.1反拉伸模reverse redrawing dies1.14.2变薄拉伸模ironing dies1.15成形模forming die

20、s1.15.11.15.21.15.31.15.41.15.5胀形模整形模缩口模扩口模翻边模翻孔模bulging dies sizingdies necking diesflaring dies flangingdies burring diescold extruding dies1.15.61.16冷挤压模1.16.1正挤压模forward extruding dies1.16.2反挤压模backward extruding dies1.16.3复合挤压模compound extruding dies1.16.4径向挤压模radial extruding dies2冲模零件2.1模架die

21、、sets2.1.1弹压导板模架die sets with spring guide plate2.1.2后导柱模架back pillar (post) sets2.1.3对角导柱模架die gonal pillar (post) sets2.1.4中间导柱模架center pillar (post) sets2.1.5精冲模架fine blanking die sets2.1.6滑动导向模架sling guide die sets2.1.7滚动导向模架anti-frtion bearing die sets2.1.8通用模架universal die sets2.2工作零件working e

22、lements2.2.1凸模punch2.2.2凹模matrix2.2.3凸凹模punch-matrix2.2.4镶件insert2.2.5拼块section2.2.6柔性模flexile dies2.3定位零件locating elements2.3.1定位销locating pin (gauge pin)2.3.2定位板locating plate2.3.3挡料销stop pin2.3.4导正销pilot pin2.3.5导料板stock guide rail2.3.6定距侧刃pitch punch2.3.7侧刃挡块stop block for pitch punch2.3.8止退键die

23、 stop2.3.9始用挡料销(块) finger stop pin (block)2.3.10侧压板se-push plate2.3.11限位块(柱) limited block (post)2.4压料、卸料零件2.4.1卸料板stripper plate2.4.2推件块ejector2.4.3推杆ejector pin2.4.4推板ejector plate2.4.5连接推杆ejector tie rod2.4.6打杆knock out pin2.4.7顶件块ker2.4.8顶杆ker pin2.4.9卸料螺钉stripper bolt2.4.10拉杆tie rod2.4.11托杆pres

24、sure pin (cushion pin)2.4.12托板supporting plate (pressure plate)2.4.13废料切断刀scrap cutter2.4.14弹顶器cushion2.4.15承料板stock supporting plate2.4.16压料板pressure plate2.4.17压边圈blank holder2.4.18齿圈压板serrated ring2.5导向零件guide elements2.5.1导柱guide pillars (guide post)2.5.2导套guide bushes2.5.3导板guide plate2.5.4滑板sl

25、eek plate2.5.5耐磨板wear plate2.5.6弹压导板spring guide plate2.5.7钢球保持圈cage2.5.8止动件retainer2.6固定零件retaining elements2.6.1上模座punch holder (upper shoe)2.6.2下模座die holder (low shoe)2.6.3凸模固定板punch plate2.6.4凹模固定板matrix plate2.6.5垫板backing plate2.6.6模柄shank2.6.7浮动模柄self-centering shank2.7其他零件2.7.1斜楔cam driver2

26、.7.2滑块sleek block3冲模设计术语3.1冲裁间隙blanking clearance3.2模具闭合高度die shut height3.3压力机闭合高度shut height of press machine3.4冲模寿命die life3.5压力中心center lf loadsatin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨dril

27、l钻boring镗blinster气泡fillet镶;嵌边through-holeform通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic

28、solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机 非标准的密封圈non-understanded seal ring bolsterbEulstE n.模座,垫板blank blANk v.冲裁,落料blanking tool落料模bush buF n.衬套cavity and core plates凹模和凸模板clampklAmp n.压板cold hobbing冷挤压copy machine仿形（加工）机床die-set模架ejector r

29、ob顶杆follow-on tool连续模Gate/runner too big水口出水直径太大guide pillars and bushes导柱和导套in-line-of-draw直接脱模 成型不良及原因分析用语Flashes披峰scratch划伤sink mark缩水pin mark顶针痕迹water leakage漏水slider jam卡滑块stick to cavity粘前模spring broken弹簧损坏insert broken镶件损坏modity mold需改模poor surface表面不够光滑material problem原料问题ehermocouple open测温

30、线损坏E.P.distance too short顶针行程太短Runner stuck to cavity side流道粘前模Unbalance part release产品脱落不平衡Bushing&nozzle not matching模嘴与喷嘴不配合Gas mark气纹Short shot不满Drag mark拉伤Weld line熔接线Part broken产品断裂Spring fail弹簧失效Ejector jam顶针卡住Insert dented镶件损坏Ejector pin broken顶针断Bum mark烧焦Flow mark流痕Shrink（ing）变形Spray silic

31、on喷油Stick to core粘后模Sticking sprue断水口Ejector pin bend顶针弯Drag mark表面有伤痕Change spare需要换零件E.p.not return fully顶针不完全复位No cavity/rev.no.无型腔号Need service需保养Machine problem机器问题Heater open热浇道加热系统损坏Gate/runner too small水口出水直径太小 表面处理关连用语age hardening时效硬化ageing老化处理air hardening气体硬化air patenting空气韧化annealing退火a

32、node effect阳极效应anodizing阳极氧化处理atomloytreatment阿扥木洛伊表面austempering奥氏体等温淬火austenite奥斯田体/奥氏体bainite贝氏体banded structure条纹状组织barrel plating滚镀barreltumbling滚筒打光blackening染黑法blue shortness青熟脆性bonderizing磷酸盐皮膜处理box annealing箱型退火box carburizing封箱渗碳bright electroplating辉面电镀bright heat treatment光辉热处理bypass hea

33、t treatment旁路热处理carbide炭化物carburized case depth浸碳硬化深层carburizing渗碳cementite炭化铁chemical plating化学电镀chemical vapor deposition化学蒸镀coarsening结晶粒粗大化coating涂布被覆cold shortness低温脆性comemtite渗碳体controlled atmosphere大气热处理corner effect锐角效应creeping discharge蠕缓放电decarburization脱碳处理decarburizing脱碳退火depth of harden

34、ing硬化深层diffusion扩散diffusion annealing扩散退火electrolytic hardening电解淬火embossing压花etching表面蚀刻ferrite肥粒铁first stage annealing第一段退火flame hardening火焰硬化flame treatment火焰处理full annealing完全退火gaseous cyaniding气体氧化法globular cementite球状炭化铁grain size结晶粒度granolite treatment磷酸溶液热处理graphitizing石墨退火hardenability硬化性ha

35、rdenability curve硬化性曲线hardening硬化heattreatment热处理hot bath quenching热浴淬火hot dipping热浸镀inductionhardening高周波硬化ion carbonitriding离子渗碳氮化ion carburizing离子渗碳处理ion plating离子电镀isothermal annealing等温退火liquid honing液体喷砂法low temperature annealing低温退火malleablizing可锻化退火martempering麻回火处理martensite马氏体/硬化铁炭metallik

36、on金属喷镀法metallizing真空涂膜nitriding氮化处理nitrocarburizing软氮化normalizing正常化oil quenching油淬化overageing过老化overheating过热pearlite针尖组织phosphating磷酸盐皮膜处理physical vapor deposition物理蒸镀plasma nitriding离子氮化pre-annealing预备退火precipitation析出precipitation hardening析出硬化press quenching加压硬化process annealing制程退火quench agein

37、g淬火老化quench hardening淬火quenching crack淬火裂痕quenching distortion淬火变形quenching stress淬火应力reconditioning再调质recrystallization再结晶redshortness红热脆性residual stress残留应力retained austenite残留奥rust prevention防蚀salt bath quenching盐浴淬火sand blast喷砂处理seasoning时效处理second stage annealing第二段退火secular distortion经年变形segre

38、gation偏析selective hardening部分淬火shot blast喷丸处理shot peening珠击法single stage nitriding等温渗氮sintering烧结处理soaking均热处理softening软化退火solution treatment固溶化热处理spheroidizing球状化退火stabilizingtreatment安定化处理straightening annealing矫直退火strain ageing应变老化stress relieving annealing应力消除退火subzero treatment生冷处理supercooling过

39、冷surface hardening表面硬化处理temper brittleness回火脆性temper colour回火颜色tempering回火tempering crack回火裂痕texture咬花time quenching时间淬火transformation变态tufftride process软氮化处理underannealing不完全退火vacuum carbonitriding真空渗碳氮化vacuum carburizing真空渗碳处理vacuumhardening真空淬火vacuum heat treatment真空热处理vacuum nitriding真空氮化water q

40、uenching水淬火wetout浸润处理Core and cavity cut in solid:型芯型腔Side core gibs and wear plates：侧型芯引导楔和耐磨板Side core heel block：侧型芯垫块Side core body block cooling：侧型芯块体冷却 机床行业部分英汉对照 按英文字母排序3-Jaws indexing spacers三爪、分割工具头A.T.C.system加工中心机刀库Aluminum continuous melting & holding furnaces连续溶解保温炉Balancingequipment平衡设

41、备Bayonet卡口Bearing fittings轴承配件Bearing processing equipment轴承加工机Bearings轴承Belt drive带传动Bending machines弯曲机Blades刀片Blades,saw锯片Bolts,screws & nuts螺栓,螺帽及螺丝Boring heads搪孔头Boring machines镗床thermal refining调质处理thermoechanical treatment加工热处理Cable making tools造线机Casting,aluminium铸铝Casting,copper铸铜Casting,gr

42、ay iron铸灰口铁Casting,malleable iron可锻铸铁Casting,other其他铸造Casting,steel铸钢Chain drive链传动Chain making tools造链机Chamfer machines倒角机Chucks夹盘Clamping/holding systems夹具/支持系统CNC bending presses电脑数控弯折机CNC boring machines电脑数控镗床CNC drilling machines电脑数控钻床CNC EDM wire-cutting machines电脑数控电火花线切削机CNC electric dischar

43、ge machines电脑数控电火花机CNC engraving machines电脑数控雕刻机CNC grinding machines电脑数控磨床CNC lathes电脑数控车床CNC machine tool fittings电脑数控机床配件CNC milling machines电脑数控铣床CNC shearing machines电脑数控剪切机CNC tooli ngs CNC刀杆CNC wire-cutting machines电脑数控线切削机Conveying chains输送链Coolers冷却机Coupling联轴器Crimping tools卷边工具Cutters刀具Cut

44、ting-off machines切断机Diamond cutters钻石刀具Dicing saws晶圆切割机Die casting dies压铸冲模Die casting machines压铸机Dies-progressive连续冲模Disposable toolholder bits舍弃式刀头Drawing machines拔丝机Drilling machines钻床Drilling machines bench钻床工作台Drilling machines,high-speed高速钻床Drilling machines,multi-spindle多轴钻床Drilling machines,

45、radial摇臂钻床Drilling machines,vertical立式钻床drills钻头Electric discharge machines（EDM）电火花机Electric power tools电动刀具Engraving machines雕刻机Engraving machines,laser激光雕刻机Etching machines蚀刻机Finishing machines修整机Fixture夹具Forging dies锻模Forging,aluminium锻铝Forging,cold冷锻Forging,copper铜锻Forging,other其他锻造Forging,steel

46、钢锻Foundry equipment铸造设备Gear cutting machines齿轮切削机Gears齿轮Gravity casting machines重力铸造机Grinder bench磨床工作台Grinders,thread螺纹磨床Grinders,tools & cutters工具磨床Grinders,ultrasonic超声波打磨机Grinding machines磨床Grinding machines,centerless无心磨床Grinding machines,cylindrical外圆磨床Grinding machines,universal万能磨床Grinding t

47、ools磨削工具Grinding wheels磨轮Hand tools手工具Hard/soft and free expansion sheet making plant硬（软）板（片）材及自由发泡板机组Heat preserving furnaces保温炉Heating treatment funaces熔热处理炉Honing machines搪磨机Hydraulic components液压元件Hydraulic power tools液压工具Hydraulic power units液压动力元件Hydraulic rotary cylinders液压回转缸Jigs钻模Lapping ma

48、chines精研机Lapping machines,centerless无心精研机Laser cutting激光切割Laser cutting for SMT stensil激光钢板切割机Lathe bench车床工作台Lathes,automatic自动车床Lathes,heavy-duty重型车床Lathes,high-speed高速车床Lathes,turret六角车床Lathes,vertical立式车床Lubricants润滑液Lubrication Systems润滑系统Lubricators注油机Machining centers,general通用加工中心Machining c

49、enters,horizontal卧式加工中心Machining centers,horizontal & vertical卧式及立式加工中心Machining centers,vertical立式加工中心Machining centers,vertical double-column type立式双柱加工中心Magnetic tools磁性工具Manifolds集合管Milling heads铣头Milling machines铣床Milling machines,bed type床身式铣床Milling machines,duplicating仿形铣床Milling machines,ho

50、rizontal卧式铣床Milling machines,turret vertical六角立式铣床Milling machines,universal万能铣床Milling machines,vertical立式铣床Milling machines,vertical & horizontal立式及卧式铣床Mold & die components模具单元Mold changing systems换模系统Mold core模芯Mold heaters/chillers模具加热器/冷却器Mold polishing/texturing模具打磨/磨纹Mold repair模具维修Molds模具Na

51、il making machines造钉机Oil coolers油冷却器Overflow cutting machines for aluminium wheels铝轮冒口切断机P type PVCwaterproof rolled sheet making plant P型PVC高分子防水PCB fine piecing systems印刷电器板油压冲孔脱料系统Pipe & tube making machines管筒制造机Planing machines刨床Planing machines vertical立式刨床Pneumatic hydraulic clamps气油压虎钳Pneumat

52、ic power tools气动工具Powder metallurgic forming machines粉末冶金成型机Presses,cold forging冷锻冲压机presses,crank曲柄压力机Presses,eccentric离心压力机Presses,forging锻压机Presses,hydraulic液压冲床Presses,knuckle joint肘杆式压力机Presses,pneumatic气动冲床Presses,servo伺服冲床Presses,transfer自动压力机Pressing dies压模Punch formers冲子研磨器Quick die change

53、systems速换模系统Quick mold change systems快速换模系统Reverberatory furnaces反射炉Rollers滚筒Rolling machines辗压机Rotary tables转台Sawing machines锯床Sawing machines,band带锯床Saws,band带锯Saws,hack弓锯Saws,horizontal band卧式带锯Saws,vertical band立式带锯shafts轴Shapers牛头刨床Shearing machines剪切机Sheet metal forming machines金属板成型机Sheet met

54、al working machines金属板加工机Slotting machines插床spindles主轴Stamping parts冲压机Straightening machines矫直机Switches & buttons开关及按钮Tapping machines攻螺丝机Transmitted chains传动链Tube bending machines弯管机Vertical hydraulic broaching machine立式油压拉床Vises虎钳Vises,tool-maker精密平口钳Wheel dressers砂轮修整器Woven-Cutting machines织麦激光切

55、割机Wrenches扳手工具常用词汇adjustable spanner活动扳手angle cutter角铣刀anvil铁钻arbour心轴backing衬垫belt sander带式打磨机buffing抛光chamfering machine倒角机chamfering tool去角刀具chisel扁錾chuck夹具compass两角规concave cutter凹面铣刀convexcutter凸形铣刀cross joint十字接头cutting edge clearance刃口余隙角drill stand钻台edge file刃用锉刀file锉刀flange joint凸缘接头grinder

56、砂轮机hammer铁锤hand brace手摇钻hatching剖面线hexagon headed bolt六角头螺栓hexagon nut六角螺帽index head分度头jack千斤顶jig治具kit工具箱lapping研磨metal saw金工锯nose angle刀角pinchers钳子pliers铗钳plug柱塞头polisher磨光器protabledriller手提钻孔机punch冲头sand paper砂纸scraper刮刀screw driver螺丝起子scribing划线second out file中纹锉spanner扳手spline broach方栓槽拉刀square直

57、角尺square sleeker方形镘刀square trowel直角度stripping剥离工具T-slot T形槽tool for lathe车刀tool point angle刀刃角tool post刀架tosecan划线盘trimming去毛边waffle die flattening压纹效平wiper脱模钳wrench螺旋扳手analog-modedevice类模器die lifter举模器argon welding氩焊pedal踩踏板stopper阻挡器flowboard流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glo

58、ve(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ringfinger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcoholcontainer沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mopthe floor拖地to clean the floor扫地to clean a table擦桌子air pipe气管packagingtool打包机packaging打包automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座