电气安全检查表electricalsafetychecklist

《电气安全检查表electricalsafetychecklist》由会员分享，可在线阅读，更多相关《电气安全检查表electricalsafetychecklist（8页珍藏版）》请在装配图网上搜索。

1、TopicDocument IDPageWorkplace safety inspection reportElectrical Safety 电气安全ELPAGE 1 OF 4A B IDInspection PointVisual CriteriaObservationNotes001Are grou nd fault circuit in terrupters (GFCI) used at the electrical source for portable electric tools and exte nsion cords?手持电动工具及延长线施工带有漏电保护装置。Criteria

2、: A GFCI must be used with any extension cords and portable electric tools, except for battery operated tools.任何延长线插座和使用常规交流电的手持电动工具都必须配有漏电保护装置Example of a GFCI in use on a retractable extension cord002003004In SHOP AREAS: Are extension cords and plug strips used only temporarily and suitable for th

3、e con diti ons of use and locati on?在商业区：延长线和插板是否适合作业环境条件？Criteria: Exte nsion cords are only to be used temporarily with portable devices, and must be removed upon completi on of the task. Plug strips are only permitted for temporary use with light duty, low current devices (such as computers or el

4、ectr onic devices). Exte nsion cords and plug strips must be protected from damage and exposure to damp or wet con diti ons dur ing use.延长线只用用于临时用电，使用后立即移除，插板只能用于带动小功率低电流 设备例如电脑和电子设备，带有延长线的插板使用时必须注意保护，避免破损 和在潮湿环境内使用。In OFFICE AREAS: Are plug strips used only for low curre nt electrical devices, and

5、are they protected from damage?在办公区：插板是否只用于带动低电流的电器设备，并且能有效预防事故？Criteria: Plug strips are only to be used for low current devices in workstati ons or offices, and must be protected from damage. Exte nsion cords are n ot permitted for any purpose other tha n temporary maintenance work.插板只能用于办公区和现场办公点

6、的低电流设备供电，并有保护装置， 延长线只能用于维修工作的临时用电线路。Are exte nsion cords heavy duty rated, with molded strai n-relief plugs and receptacles额定负荷大的延长线和插头是否是一次压模成型的？Criteria: Extension cords must be at least type SE, SJ, SO, or ST 14/3 con structi on, and must have factory-assembled cord en ds. No custom-made or modif

7、ied cords are permitted.夕卜包绝缘层为 SE, SJ, SO,或ST天然丝包外径比为14/3型的延长线和端头为原厂定制的电缆，不允许修改和成型端头。Extension cords are permitted for temporary use with portable power tools, portable lighting and electrical devices. Cords must be remcved and stored alter completi on of the ta sk.Plugstrips are permitted in offic

8、e areas only for electronic devices such as computers. Plugstnips must be protected from damage.Plug ends are molded over the cordFlexible c；ordtypfe is printed or imprinted on the oord jacketColumn A: Priority Code. Column B: Location Code.Cord must be free of any tape, cuts or tears in the jacket,

9、 exposure of any wire conductors； and signs of damage from heat or chemicalsE xtension cord wilh plug blades and ground prong intad. Blades are straight and undamaged-Example of an extension cord manufactured with a multiple outlet cord交4一 rMu K卜fixture temporary light string. All bulbs must be cage

10、d.rcplight Bulb must be caged. Not to be used as an extenscn cordHalogen fight. CAUTION： extremely hot. Not to be used near flammable or combustible materials.WORKPLACE SAFETY INSPECTION REPORTTopicElectrical Safety 电气安全Document IDELPagePAGE 2 OF 4Are flexible cords and cables free of splices, taps,

11、 tape, and gen eraldamage?软线和延长些的接头是否用绝缘胶布做处理和避免漏电危险？Criteria: Flexible cable and extension cords must show no sig ns of tearing or exposure of con ductors. Cords must not be repaired with tape.延长线和软线的绝缘破损和漏岀导体部分必须使用绝缘胶布进行保护处理。006 If the extension cord, tool, or device originally had a ground prong,

12、 is it still inplace?延长线、电气工具设备带有接地端插头的接地端子是否完好？Criteria: Any device that was man ufactured with a 3rd prong to act as a grou nd must have the grou nd prong in tact and un damaged.任何三爪插头的第三插脚起到接地保护作用，所以三个插脚都必须完好。007 Are multiple plug adaptors prohibited?多功能插头适配器是否禁止使用？Criteria: Multiple plug adapter

13、s (ofte n called power taps) are not permitted unl ess man ufactured as part of an exte nsion cord assembly.多功能插头适配器(常称为插头切换器)不准使用，除非延长线自带的。008 Are portable lights or temporary light ing used properly?是否正确使用手持照明和临时照明装置。Criteria: Portable lights (drop lights, spotlights, multi-fixture light assemblie

14、s) must only be used for temporary task lighting, and removed after use.Halogen lights become extremely hot during use, and must be isolated from all flammable and combustible materials. Cords and lights must be protected from damage and exposure to damp or wet conditions during use. Portable lights

15、 must not be hung from any moveable source: i.e. elevator hoist ropes, crane hoist etc.手提灯(落灯、射灯、多光源照明组合装置)只能用于临时照 明，用完后立即移除。卤素灯使用过程会产生大量热量，所以安装位置需要远 离易燃、可燃物质，在室外及潮湿环境中使用，灯和线路必须设有安全防护， 避免损坏和漏电，手提灯不能悬挂在任何可移动的物体上，例如：电梯提升钢 丝绳和起重机吊索上。Workplace safety inspection reportTopicElectrical Safety 电气安全Document

16、IDELPagepage 3 OF 4Column A: Priority Code. Column B: Location Code.IDInspection PointVisual CriteriaO bservationNotesExample of an electrical panel free of obstructi ons: 30” wide working clearanee and 36 ” front working cleara nee009 Are electrical pan els, cab in ets, and disc onn ects free from

17、obstructi on?配电设施前是否畅通无阻？Criteria: Electrical pan els, cab in ets, switchgear, and disc onn ects must have a mini mum un obstructed space 36 in ches (1 M) in front of the panel and 36 in ches (1 M) wide to permit safe access to ope n and work in side of electrical pa nels and boxes.配电箱、配电柜、开关柜前需要保持一

18、个最小安全距离为电柜前1m宽1m ,保证能够安全的打开电柜操作电柜内面板。010Are all disc onn ects and circuit breakers labeled to in dicate their use orequipme nt served?开关是否有状态标识牌，标明开合状态？Criteria:Disc onn ects and circuit breakers must be labeled to ide ntify theequipme nt, light ing, or circuit the switch or circuit breaker con trol

19、s.断路器和开关上必须标识清楚指示灯或短路设备通路和断路状态标识。Example of circuit breaker panel with ID card on doorExample of 風 di$Knnect switch with label indicating circuit or equipment011Are all electrical cabinets, junction boxes, outlets, and switches fully enclosed?所有电柜、电箱、接线盒是否都是密封良好的？Criteria: No openings exposing the i

20、nterior of the electrical enclosure are permitted on any surface of the enclosure. All unused holes and openings must be blocked or filled with fittings or block-off plates designed for this purpose. Unused knock-out and twist-out tabs must be tight and secure. Covers must be screwed securely to dev

21、ice or box. Tape is not permitted as a cover for openings. 不允许在 任何密封跌电气外壳随意开孔，所有未使用的开孔必须用专门设计挡板封堵，未使 用的和淘汰的开孔必须密封和确保安全，电箱、设备的门必须盖紧安全防护门，不 准使用胶带代替密封装置。Example of an electrical box with unused openings blocked with knock- out乳 Fittings connecting pipe to the box are correctly instaled, and the covers

22、are in place and tightly screwed to box.WORKPLACE SAFETY INSPECTION REPORTTopicElectrical Safety 电气安全Document IDELPagePAGE 4 OF 4ABIDI nspection Point012Are clamps or other securi ng means provided on flexible cords or cables at plugs, receptacles, tools, equipme nt, pan els and jun cti on boxes, et

23、c., and is the cord jacket securely held in place?在插头、插座，工具，设备，面板和接线盒的电缆进口处 是否装有线夹和其他安防装置用于防止电缆磨损？Criteria: Flexible cords must have a strain relief device in stalled on or man ufactured as part of the cord assembly to preve nt wear and extreme bends or crack ing of the in sulat ing jacket and con d

24、uctors. The stra in relief also preve nts the cord con ductors from pulli ng out of the device. Overhead bus drops must be securely clamped and stra in relieved at the overhead box and at the floor-level point of conn ecti on. If plug sets are used, they must be locking connectors with strain relief

25、. A cable support grip must be used at the transition from overhead to vertical drop.移动电缆必须安装有防止极端变形和弯曲情况下绝缘保护和 导体破损的应力消除装置和组件，应力缓解保护装置还可以防止 电线受力从设备接口抽岀，架空总线向下悬挂的绝缘端子必须使 用插销与夹住电线的应变消除装置固定使用，并与接地端连接 使用集成插头必须自带应变缓冲装置，电缆的应力缓冲装置支撑 能力必须满足其从上到下落差产生的重量。013Are rubber mats placed on the floor in front of ele

26、ctrical enclosures and equipment if work is performed on live circuitry? 带电作业的电柜和设备前是否有绝缘地垫？Criteria: Authorized personnel working on live circuitry must stand on an insulating rubber mat to prevent electrocution if the worker comes into bodily con tact with an en ergized comp onent or con ductor.带电

27、作业必须有持证的电工进行操作，作业时站在 绝缘脚垫上预防作业时碰到带电部位导致触电。Visual CriteriaObservation Notes,若Example of an electrical box and conduit with correctly installed strain reliefs.Flexible cable bus drops must have a cable clamp and support grip from the overhead junction box or disconnect, and the floor level connection be strain relieved. Flexible cords on equipment 目nH tools must have strain relief.Eyamplle of rubber floormat m use in front of an electrical enclosure to insulate the worker.