led产品规格书

《led产品规格书》由会员分享，可在线阅读，更多相关《led产品规格书（8页珍藏版）》请在装配图网上搜索。

1、ShenZhen JuFei Optoelectronics Co.,Ltd.0 01 1.J JP P.S SY YL L0 01 1?Customer:Technical Data Sheet PN:JP.SYL01 For:IF=350mA Contents 1.Features 2.Applications 3.Package outline dimension 4.Absolute maximum ratings 5.Electrical-optical characteristics 6.Typical electro-optical characteristics curves

2、7.Package specifications 8.Label description 9.BIN range 10.Reliability test items and conditions 11.Precautions for use Customer confirm Approved byChecked by Issued by ShenZhen JuFei Optoelectronics Co.,Ltd.7F-8,DongFangMing Industrial City,NO.83,DaBao Road,33 District,BaoAn District,ShenZhen City

3、 Tel:+86-755-29632290 Fax:+86-755-29632282 ShenZhen JuFei Optoelectronics Co.,Ltd.0 01 1.J JP P.S SY YL L0 01 1 Ver.A1 Page 1 of 7 1、Features:1.1 Package:19.9X8.0X7.2mm 1.2 Emitted Color:Yellow 1.3 Mono-color type 1.4 Soldering methods:hand soldering 1.5 Comply RoHS standard.2、Applications:2.1 Decor

4、ation lights,garden lighting 2.2 Architectural lighting,contour lighting 3、Package Outline Dimension:Internal circuitSide viewTop viewCathode(-)Anode(+)NOTES:1.All dimensions are in millimeters(Tolerance is 0.2mm)ShenZhen JuFei Optoelectronics Co.,Ltd.0 01 1.J JP P.S SY YL L0 01 1 Ver.A1 Page 2 of 7

5、 4、Absolute Maximum Ratings(Ta=25)Parameter Symbol Rating Unit Power Dissipation Pd 850 mW Forward Current IF 350 mA Peak Forward Current 1 IFP 500 mA LED Junction Temperature Tj 125 Reverse Voltage VR 5 V Hand Soldering Temperature Tsol 350(for 3 seconds)Operating Temperature Topr-35+85 Storage Tem

6、perature Tstg-40+100 IFP condition:pulse width 0.1msec,duty cycle 1/10.5、Electrical-optical characteristics(Ta=2525)Parameter Symbol Min.Typ.Max.Unit ConditionForward Voltage Vf 2.0-2.7 V 4 Code Flux 20-30 lm 5 Code Flux 30-40 lm Luminous Flux 6 Code Flux 40-50 lm Wavelength Wd 588-598 nm Viewing An

7、gle 21/2-120-deg IF=350mAReverse Current IR-10 uA VR=5V ShenZhen JuFei Optoelectronics Co.,Ltd.0 01 1.J JP P.S SY YL L0 01 1 Ver.A1 Page 3 of 7 6、Typical Electro-Optical Characteristics Curves 0Rth(j-a)=60/wRth(j-a)=50/wRth(j-a)=40/wRth(j-a)=30/w0502510075125100200300400500yellow6407004004601.00.50.

8、05805202.72.52.32.11.91.7Forward current(mA)204060801000400300200100500100Relative luminous intensity vs.forward current1200Forward voltage(V)Forward current vs.forward voltage(Ta=25)Forward current(mA)200300400500Relative intensity VS wavelength(Ta=25)Wavelength(nm)Relative radiant intensityRelativ

9、e luminous intensity(%)junction temperatureRelative Radiant IntensityRelative luminous output(%)Radiation diagramJunction Temperature.Tj()004020208060100(Normalized 350mA)Luminous intensity output vs.Ambient temperature Ta()Forward current derating curve vs.ambient temperatureForward current(mA)0102

10、030405060700.40.21.00.90.80.70.60.50.30.180406080100120140160180200 ShenZhen JuFei Optoelectronics Co.,Ltd.0 01 1.J JP P.S SY YL L0 01 1 Ver.A1 Page 4 of 7 7、Package specifications(Units:mm)Loaded quantity:100pcs/tray 10tray/box 65TrayCoverBox 8、Label description：BIN description：x/x/x-x Forward volt

11、age BIN CODE Wavelength BIN CODE Luminous intensity BIN CODE Such as:BIN:5/F/4-1 5 show luminous intensity BIN CODE F show wavelength BIN CODE 4-1 show forward voltage BIN CODE 产品追踪码产品型号 产品 BIN生产日期 生产批次 RoHS 标签 数量 检验盖章ShenZhen JuFei Optoelectronics Co.,Ltd.0 01 1.J JP P.S SY YL L0 01 1 Ver.A1 Page 5

12、 of 7 9、BIN range Luminous Flux(tolerance is 10%If=350mA):BIN CODE Min.(lm)Max.(lm)4 20 30 5 30 40 6 40 50 Forward voltage(tolerance is 0.1V If=350mA)BIN CODE Min.(v)Max.(v)1-2 2.0 2.1 2-1 2.1 2.2 2-2 2.2 2.3 3-1 2.3 2.4 3-2 2.4 2.5 4-1 2.5 2.6 4-2 2.6 2.7 Wavelength ranks(tolerance is 1nmIf=350mA)B

13、IN CODE Min.(nm)Max.(nm)F 586 592 I 592 598 10、Reliability test items and conditions:No.Test Item Test Conditions Sample size Ac/Re 1 Operation Life Test If=DC350mA Temp:Room temperature Test time=1000hrs 10 0/1 2 High Temperature High Humidity Temp.=+65 RH=90%HR Test time=1000hrs 10 0/1 3 Thermal S

14、hock-40 +100 20min 10s 20min Test Time=100cycles 10 0/1 4 High Temperature Storage High Temp.=+100 Test time=1000hrs 10 0/1 5 Low Temperature Storage Low Ta=-40 Test time=1000hrs 10 0/1 6 Temperature Cycle-40 +100 60min 20min 60min Test Time=20cycle 10 0/1 Judgment criteria of failure for the reliab

15、ility Iv:Below 70%of initial values Vf:Over 20%of upper limit value ShenZhen JuFei Optoelectronics Co.,Ltd.0 01 1.J JP P.S SY YL L0 01 1 Ver.A1 Page 6 of 7 Note:Measurement shall be taken between 2 hours and after the test LED have been returned to normal ambient conditions after completion of each

16、test.11、Precautions for use:11.1 Soldering a.Power LED silicon encapsulant is very flexible,dont pressure on the radiant surface of the Power LED.b.Dont touch the radiant surface of the Power LED when process manual soldering,Recommended with a iron within 350 temperature on the heating platform,and

17、 the conduct terminal can not connect the LED pin.11.2 Cleaning a.Dont be cleaned with ultrasonic.b.Recommended to wipe with isopropyl alcohol or pure alcohol,wiping time should not be more than one minute.LED must be placed at room temperature for fifteen minutes before using.After cleaning,you mus

18、t insure the radiant surface is clean.Otherwise,foreign impurity can cause radiant color different.c.LED can not contact with trichloroethylene,acetone,sulfide,nitride,acid,alkali,salt,These chemical matter can destroy LED.11.3 Sealing a.Sealing resin can not contain sodium-ion,sulfide,because these

19、 matter can affect fluorescence powder poisoning,change its color.b.When using normal sealing resin,Recommended to light and test for 168hrs under normal temperature before batch product.11.4 Storage a.Dont open the moisture proof bag before ready to use the Power LED.The LED should be kept at 30 or

20、 less and 60%RH or less before opening the package.Storage period is one year before opening the package.b.After opening the package,the Power LED should be kept at 30-35%RH or less,and it should be used within 48 hrs.c.If the Power LED exposure for 48 hrs,baking is required before use.Bake conditio

21、n as below:605 for 12 hrs for roll goods.1055 for 1 hrs for bulk goods.All around environment have no acid,alkali,corrosive gas,vibration and magnetic field.11.5 Static a.Static and Peak surge voltage can destroy Power LED,Avoiding Instantaneous voltage when on or off.b.Please wear Anti-static wrist

22、 band,Anti-static glove,Anti-static shoes in the course of operation,and the equipment must be grounded.ShenZhen JuFei Optoelectronics Co.,Ltd.0 01 1.J JP P.S SY YL L0 01 1 Ver.A1 Page 7 of 7 c.If Power LED destroyed,leakage current may be increase obviously,and forward voltage will be falling or fa

23、ilure light when use low current.11.6 Test a.Should avoid exorbitant instantaneous current on Power LED,otherwise,Gold wire will be burned out and chip will be burned up.b.The forward voltage reduce gradually when Power LED is on,Recommended for test with continuous current.11.7 Heat elimination Tem

24、perature rise with the Power LED on,care for the module thermal transmission and heat elimination when design,the brightness and lifetime of Power LED will be affected if thermal transmission and heat elimination are bad.11.8 Others a.Recommended to be used in series one resistance and continuous cu

25、rrent driver for power led when design.b.Some Products heat sink have polarity,please refer to product specification before design.c.When lighting,Please dont look at the radiant surface of LED directly,otherwise the strong intensity will burn your eyes.d.Dont lighting for long time without heat radiator,otherwise,the power LED damages easily.