梁的有限元建模与变形分析

梁的有限元建模与变形分析计算分析模型如图1-1 所示, 习题文件名: beam。NOTE:要求选择不同形状的截面分别进行计算。图1-1梁的计算分析模型梁截面分别采用以下三种截面（单位：m）： 矩形截面： 圆截面： 工字形截面：B=0.1, H=0.15 R=0.1 w1=0.1，w2=0.1，w3=0.2, t1=0.0114，t2=0.0114，t3=0.0071.1 进入ANSYS程序 ANSYSED 6.1 Interactive change the working directory into yours input Initial jobname: beamRun1.2设置计算类型 ANSYS Main Menu: Preferences select Structural OK1.3选择单元类型ANSYS Main Menu: Preprocessor Element TypeAdd/Edit/Delete Add select Beam 2 node 188 OK (back to Element Types window) Close (the Element Type window)1.4定义材料参数ANSYS Main Menu: Preprocessor Material Props Material Models Structural Linear Elastic Isotropic input EX:2.1e11, PRXY:0.3 OK1.5定义截面ANSYS Main Menu: Preprocessor Sections Beam Common Sectns 分别定义矩形截面、圆截面和工字形截面：矩形截面:ID=1,B=0.1，H=0.15 Apply 圆截面：ID=2,R=0.1 Apply 工字形截面：ID=3,w1=0.1，w2=0.1，w3=0.2，t1=0.0114，t2=0.0114，t3=0.007 OK 1.6生成几何模型ü 生成特征点 ANSYS Main Menu: Preprocessor Modeling Create Keypoints In Active CS 依次输入三个点的坐标：input:1(0,0),2(10,0),3(5,1) OKü 生成梁ANSYS Main Menu: Preprocessor Modeling Create Lines lines Straight lines 连接两个特征点，1(0,0),2(10,0) OK1.7 网格划分 ANSYS Main Menu: Preprocessor Meshing Mesh Attributes Picked lines OK 选择: SECT:1（根据所计算的梁的截面选择编号）；Pick Orientation Keypoint(s):YES拾取：3#特征点(5,1) OKMesh Tool Size Controls) lines: Set Pick All(in Picking Menu) input NDIV:5 OK (back to Mesh Tool window) Mesh Pick All (in Picking Menu) Close (the Mesh Tool window)1.8 模型施加约束ü 最左端节点加约束ANSYS Main Menu: Solution Define Loads Apply Structural Displacement On Nodes pick the node at (0,0) OK select UX, UY,UZ,ROTX OKü 最右端节点加约束ANSYS Main Menu: Solution Define Loads Apply Structural Displacement On Nodes pick the node at (10,0) OK select UY,UZ,ROTX OKü 施加y方向的载荷ANSYS Main Menu: Solution Define Loads Apply Structural Pressure On Beams Pick All VALI:100000 OK1.9 分析计算 ANSYS Main Menu: Solution Solve Current LS OK(to close the solve Current Load Step window) OK1.10 结果显示 ANSYS Main Menu: General Postproc Plot Results Deformed Shape select Def + Undeformed OK (back to Plot Results window) Contour Plot Nodal Solu select: DOF solution, UY, Def + Undeformed , Rotation, ROTZ ,Def + UndeformedOK1.11 退出系统 ANSYS Utility Menu: File Exit Save EverythingOK