H3C路由学习笔记-静态路由

《H3C路由学习笔记-静态路由》由会员分享，可在线阅读，更多相关《H3C路由学习笔记-静态路由（14页珍藏版）》请在装配图网上搜索。

1、 H3C路由（MSR26-30）1、进入系统视图Startup configuration file does not exist.Performing automatic configuration. Press CTRL_D to break.-按Ctrl + D键终止设备查找自动配置Automatic configuration attempt: 1.Not ready for automatic configuration: no interface available.Waiting for the next.Automatic configuration is aborted.-按

2、Ctrl + D键后放弃自动配置的尝试Line aux0 is available.Press ENTER to get started.-到这里系统启动完毕，按回车键%Aug 22 09:19:53:318 2014 H3C SHELL/5/SHELL_LOGIN: TTY logged in from aux0.-再按一次回车键system-viewH3C2、修改路由器名称sysH3Csysname 名称如将默认的路由器名称改为RoNetwork_Dept，Ro表示设备类型为路由器，Network_Dept表示部门名称，以后看到这个名称就知道这是什么设备、在什么位置。建议以后都采用这种方式

3、来给设备命名，以方便管理。H3Csysname RoNetwork_DeptRoNetwork_Dept如果要恢复默认名称，使用undo sysname命令：RoNetwork_Deptundo sysnameH3C3、显示路由表（1）IPv4显示路由表概要信息：RoNetwork_Deptdisplay ip routing-table显示路由表详细信息：RoNetwork_Deptdisplay ip routing-table verbose显示某种路由协议的信息：RoNetwork_Deptdisplay ip routing-table protocol bgp|direct|gua

4、rd|isis|ospf|rip|static还有其他信息，可使用？显示帮助以便选择：RoNetwork_Deptdisplay ip routing-table ?（2）IPv6只需将IPv4的命令中ip替换成ipv6即可。4、配置接口syssystem-viewH3Cint 接口名称如配置G0/0接口：RoNetwork_Deptint g0/0RoNetwork_Dept-GigabitEthernet0/0-进入接口配置视图配置IP地址：RoNetwork_Dept-GigabitEthernet0/0ip add 12.0.0.1 ?-后面跟掩码长度也行，跟掩码也行 INTEGER

5、IP mask length X.X.X.X IP maskRoNetwork_Dept-GigabitEthernet0/0ip add 12.0.0.1 24 -24表示掩码长度为24位，和255.255.255.0等效RoNetwork_Dept-GigabitEthernet0/0undo shutdown-激活接口RoNetwork_Dept-GigabitEthernet0/0dis int g0/0-查看接口信息5、信息回显及tracert为了防止命令被系统输出的消息打断，可以配置信息回显：RoNetwork_Deptinfo-center synchronous为防止trace

6、rt超时，链路两端的设备都要开启以下功能：RoNetwork_Deptip redirects enable 开启设备的ICMP重定向报文的发送功能RoNetwork_Deptip ttl-expires enable开启设备的ICMP超时报文的发送功能RoNetwork_Deptip unreachable enable 开启设备的ICMP目的不可达报文的发送功能6、配置静态路由拓扑图：RoNetwork_Dept端：sysSystem View: return to User View with Ctrl+Z.H3Csys RoNetwork_DeptRoNetwork_Deptinfo

7、syncInfo-center synchronous output is on.RoNetwork_Deptint lo0RoNetwork_Dept-LoopBack0ip add 192.168.1.1 24RoNetwork_Dept-LoopBack0int g0/0RoNetwork_Dept-GigabitEthernet0/0ip add 12.0.0.1 24RoNetwork_Dept-GigabitEthernet0/0undo shRoNetwork_Dept-GigabitEthernet0/0ip route 192.168.2.2 255.255.255.255

8、12.0.0.2RoNetwork_Dept%Aug 22 11:45:32:415 2014 RoNetwork_Dept IFNET/3/PHY_UPDOWN: Physical state on the interface GigabitEthernet0/0 changed to up.%Aug 22 11:45:32:416 2014 RoNetwork_Dept IFNET/5/LINK_UPDOWN: Line protocol state on the interface GigabitEthernet0/0 changed to up.-系统发出的消息，g0/0接口已经up了

9、RoNetwork_Deptdis ip roDestinations : 17 Routes : 17Destination/Mask Proto Pre Cost NextHop Interface0.0.0.0/32 Direct 0 0 127.0.0.1 InLoop012.0.0.0/24 Direct 0 0 12.0.0.1 GE0/012.0.0.0/32 Direct 0 0 12.0.0.1 GE0/012.0.0.1/32 Direct 0 0 127.0.0.1 InLoop012.0.0.255/32 Direct 0 0 12.0.0.1 GE0/0127.0.0

10、.0/8 Direct 0 0 127.0.0.1 InLoop0127.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0127.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0192.168.1.0/24 Direct 0 0 192.168.1.1 Loop0192.168.1.0/32 Direct 0 0 192.168.1.1 Loop0192.168.1.1/32 Direct 0 0 127.0.0.1 InLoop0192.168.1

11、.255/32 Direct 0 0 192.168.1.1 Loop0192.168.2.2/32 Static 60 0 12.0.0.2 GE0/0224.0.0.0/4 Direct 0 0 0.0.0.0 NULL0224.0.0.0/24 Direct 0 0 0.0.0.0 NULL0255.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0RoNetwork_Deptping 192.168.2.2 -使用ping命令测试路由是否配置正确Ping 192.168.2.2 (192.168.2.2): 56 data bytes, press

12、CTRL_C to break56 bytes from 192.168.2.2: icmp_seq=0 ttl=255 time=1.457 ms56 bytes from 192.168.2.2: icmp_seq=1 ttl=255 time=1.113 ms56 bytes from 192.168.2.2: icmp_seq=2 ttl=255 time=1.168 ms56 bytes from 192.168.2.2: icmp_seq=3 ttl=255 time=1.189 ms56 bytes from 192.168.2.2: icmp_seq=4 ttl=255 tim

13、e=1.049 ms- Ping statistics for 192.168.2.2 -5 packets transmitted, 5 packets received, 0.0% packet lossround-trip min/avg/max/std-dev = 1.049/1.195/1.457/0.140 msRoNetwork_Dept%Aug 22 11:49:29:304 2014 RoNetwork_Dept PING/6/PING_STATISTICS: Ping statistics for 192.168.2.2: 5 packets transmitted, 5

14、packets received, 0.0% packet loss, round-trip min/avg/max/std-dev = 1.049/1.195/1.457/0.140 ms.RoNetwork_DeptRoNetCenter端：sysSystem View: return to User View with Ctrl+Z.H3Csys RoNetCenterRoNetCenterinfo syncInfo-center synchronous output is on.RoNetCenterint lo0RoNetCenter-LoopBack0ip add 192.168.

15、2.2 32RoNetCenter-LoopBack0int g0/0RoNetCenter-GigabitEthernet0/0ip add 12.0.0.2 24RoNetCenter-GigabitEthernet0/0undo shRoNetCenter-GigabitEthernet0/0quitRoNetCenterip ro 192.168.1.1 255.255.255.255 12.0.0.1RoNetCenterdis ip roDestinations : 14 Routes : 14Destination/Mask Proto Pre Cost NextHop Inte

16、rface0.0.0.0/32 Direct 0 0 127.0.0.1 InLoop012.0.0.0/24 Direct 0 0 12.0.0.2 GE0/012.0.0.0/32 Direct 0 0 12.0.0.2 GE0/012.0.0.2/32 Direct 0 0 127.0.0.1 InLoop012.0.0.255/32 Direct 0 0 12.0.0.2 GE0/0127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0127.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0127.0.0.1/32 Direct 0

17、0 127.0.0.1 InLoop0127.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0192.168.1.1/32 Static 60 0 12.0.0.1 GE0/0192.168.2.2/32 Direct 0 0 127.0.0.1 InLoop0224.0.0.0/4 Direct 0 0 0.0.0.0 NULL0224.0.0.0/24 Direct 0 0 0.0.0.0 NULL0255.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0RoNetCenter配置等价静态路由RoNetwork_D

18、ept端：RoNetwork_Deptint g0/1RoNetwork_Dept-GigabitEthernet0/1ip add 21.0.0.1 24RoNetwork_Dept-GigabitEthernet0/1undo shRoNetwork_Dept-GigabitEthernet0/1quitRoNetwork_Deptip ro 192.168.2.2 255.255.255.255 21.0.0.2RoNetwork_Deptdis ip roDestinations : 21 Routes : 22Destination/Mask Proto Pre Cost NextH

19、op Interface0.0.0.0/32 Direct 0 0 127.0.0.1 InLoop012.0.0.0/24 Direct 0 0 12.0.0.1 GE0/012.0.0.0/32 Direct 0 0 12.0.0.1 GE0/012.0.0.1/32 Direct 0 0 127.0.0.1 InLoop012.0.0.255/32 Direct 0 0 12.0.0.1 GE0/021.0.0.0/24 Direct 0 0 21.0.0.1 GE0/121.0.0.0/32 Direct 0 0 21.0.0.1 GE0/121.0.0.1/32 Direct 0 0

20、 127.0.0.1 InLoop021.0.0.255/32 Direct 0 0 21.0.0.1 GE0/1127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0127.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0127.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0192.168.1.0/24 Direct 0 0 192.168.1.1 Loop0192.168.1.0/32 Direct 0 0 192.1

21、68.1.1 Loop0192.168.1.1/32 Direct 0 0 127.0.0.1 InLoop0192.168.1.255/32 Direct 0 0 192.168.1.1 Loop0192.168.2.2/32 Static 60 0 12.0.0.2 GE0/021.0.0.2 GE0/1224.0.0.0/4 Direct 0 0 0.0.0.0 NULL0224.0.0.0/24 Direct 0 0 0.0.0.0 NULL0255.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0RoNetCenter端：RoNetCenteri

22、nt g0/1RoNetCenter-GigabitEthernet0/1ip add 21.0.0.2 24RoNetCenter-GigabitEthernet0/1undo shRoNetCenter-GigabitEthernet0/1quitRoNetCenterip ro 192.168.1.1 255.255.255.255 21.0.0.1RoNetCenterdis ip roDestinations : 18 Routes : 19Destination/Mask Proto Pre Cost NextHop Interface0.0.0.0/32 Direct 0 0 1

23、27.0.0.1 InLoop012.0.0.0/24 Direct 0 0 12.0.0.2 GE0/012.0.0.0/32 Direct 0 0 12.0.0.2 GE0/012.0.0.2/32 Direct 0 0 127.0.0.1 InLoop012.0.0.255/32 Direct 0 0 12.0.0.2 GE0/021.0.0.0/24 Direct 0 0 21.0.0.2 GE0/121.0.0.0/32 Direct 0 0 21.0.0.2 GE0/121.0.0.2/32 Direct 0 0 127.0.0.1 InLoop021.0.0.255/32 Dir

24、ect 0 0 21.0.0.2 GE0/1127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0127.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0127.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0192.168.1.1/32 Static 60 0 12.0.0.1 GE0/021.0.0.1 GE0/1192.168.2.2/32 Direct 0 0 127.0.0.1 InLoop0224.0.0.0/4

25、 Direct 0 0 0.0.0.0 NULL0224.0.0.0/24 Direct 0 0 0.0.0.0 NULL0255.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0测试：RoNetwork_Deptping 192.168.2.2Ping 192.168.2.2 (192.168.2.2): 56 data bytes, press CTRL_C to break56 bytes from 192.168.2.2: icmp_seq=0 ttl=255 time=0.935 ms56 bytes from 192.168.2.2: icmp

26、_seq=1 ttl=255 time=1.156 ms56 bytes from 192.168.2.2: icmp_seq=2 ttl=255 time=0.732 ms56 bytes from 192.168.2.2: icmp_seq=3 ttl=255 time=1.301 ms56 bytes from 192.168.2.2: icmp_seq=4 ttl=255 time=0.733 ms- Ping statistics for 192.168.2.2 -5 packets transmitted, 5 packets received, 0.0% packet lossr

27、ound-trip min/avg/max/std-dev = 0.732/0.971/1.301/0.227 msRoNetCenterping -r 192.168.1.1-“-r”表示“Record route”，记录路由Ping 192.168.1.1 (192.168.1.1): 56 data bytes, press CTRL_C to break56 bytes from 192.168.1.1: icmp_seq=0 ttl=255 time=0.827 msRR: 21.0.0.1 12.0.0.256 bytes from 192.168.1.1: icmp_seq=1

28、ttl=255 time=0.964 msRR: 12.0.0.1 12.0.0.256 bytes from 192.168.1.1: icmp_seq=2 ttl=255 time=1.895 msRR: 21.0.0.1 12.0.0.256 bytes from 192.168.1.1: icmp_seq=3 ttl=255 time=0.673 msRR: 12.0.0.1 12.0.0.256 bytes from 192.168.1.1: icmp_seq=4 ttl=255 time=0.905 msRR: 21.0.0.1 12.0.0.2- Ping statistics

29、for 192.168.1.1 -5 packets transmitted, 5 packets received, 0.0% packet lossround-trip min/avg/max/std-dev = 0.673/1.053/1.895/0.432 ms-数据包被轮流在两条链路上发送，但是奇怪的是，只从一条链路返回，这与GNS3的Cisco路由器不一样，Cisco的是从哪条链路出去就从哪条链路返回：参考：R1#pingProtocol ip:Target IP address: 192.168.2.2Repeat count 5:Datagram size 100:Timeou

30、t in seconds 2:Extended mands n: ySource address or interface:Type of service 0:Set DF bit in IP header? no:Validate reply data? no:Data pattern 0xABCD:Loose, Strict, Record, Timestamp, Verbosenone: rNumber of hops 9 :Loose, Strict, Record, Timestamp, VerboseRV: r% No room for that optionLoose, Stri

31、ct, Record, Timestamp, VerboseRV: Record% No room for that optionLoose, Strict, Record, Timestamp, VerboseRV:Sweep range of sizes n:Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 192.168.2.2, timeout is 2 seconds:Packet has IP options: Total option bytes= 39, padded length=40 Record

32、 route: (0.0.0.0) (0.0.0.0) (0.0.0.0) (0.0.0.0) (0.0.0.0) (0.0.0.0) (0.0.0.0) (0.0.0.0) (0.0.0.0)Request 0 timed outRequest 1 timed outReply to request 2 (32 ms). Received packet has options Total option bytes= 40, padded length=40 Record route:(12.0.0.1)出去 (192.168.2.2) (12.0.0.2)(12.0.0.1) 回来 (0.0

33、.0.0) (0.0.0.0) (0.0.0.0) (0.0.0.0) (0.0.0.0) End of listReply to request 3 (48 ms). Received packet has options Total option bytes= 40, padded length=40 Record route:(21.0.0.1) (192.168.2.2) (21.0.0.2)(21.0.0.1) (0.0.0.0) (0.0.0.0) (0.0.0.0) (0.0.0.0) (0.0.0.0) End of listReply to request 4 (24 ms)

34、. Received packet has options Total option bytes= 40, padded length=40 Record route:(12.0.0.1) (192.168.2.2) (12.0.0.2)(12.0.0.1) (0.0.0.0) (0.0.0.0) (0.0.0.0) (0.0.0.0) (0.0.0.0) End of listSuccess rate is 60 percent (3/5), round-trip min/avg/max = 24/34/48 msRoNetwork_Deptint g0/0RoNetwork_Dept-Gi

35、gabitEthernet0/0sh -关闭G0/0接口，看看还能不能ping通RoNetwork_Dept-GigabitEthernet0/0%Aug 22 12:11:22:912 2014 RoNetwork_Dept IFNET/3/PHY_UPDOWN: Physical state on the interface GigabitEthernet0/0 changed to down.%Aug 22 12:11:22:913 2014 RoNetwork_Dept IFNET/5/LINK_UPDOWN: Line protocol state on the interface

36、GigabitEthernet0/0 changed to down.quitRoNetwork_Deptping 192.168.2.2Ping 192.168.2.2 (192.168.2.2): 56 data bytes, press CTRL_C to break56 bytes from 192.168.2.2: icmp_seq=0 ttl=255 time=0.676 ms56 bytes from 192.168.2.2: icmp_seq=1 ttl=255 time=0.626 ms56 bytes from 192.168.2.2: icmp_seq=2 ttl=255

37、 time=0.756 ms56 bytes from 192.168.2.2: icmp_seq=3 ttl=255 time=0.952 ms56 bytes from 192.168.2.2: icmp_seq=4 ttl=255 time=0.740 ms- Ping statistics for 192.168.2.2 -5 packets transmitted, 5 packets received, 0.0% packet lossround-trip min/avg/max/std-dev = 0.626/0.750/0.952/0.111 msRoNetwork_Dept%

38、Aug 22 12:11:33:357 2014 RoNetwork_Dept PING/6/PING_STATISTICS: Ping statistics for 192.168.2.2: 5 packets transmitted, 5 packets received, 0.0% packet loss, round-trip min/avg/max/std-dev = 0.626/0.750/0.952/0.111 ms.可见，当其中一条链路down了之后，数据包可以通过另一条链路发往目的地。配置非等价静态路由：RoNetwork_Deptint g0/0RoNetwork_Dept

39、-GigabitEthernet0/0undo sh -重新激活G0/0接口RoNetwork_Dept-GigabitEthernet0/0quitRoNetwork_Deptundo ip ro 192.168.2.2 255.255.255.255 12.0.0.2 -删除前面配置的路由RoNetwork_Deptundo ip ro 192.168.2.2 255.255.255.255 21.0.0.2-删除前面配置的路由RoNetwork_Deptip ro 192.168.2.2 255.255.255.255 12.0.0.2 preference 1配置非等价静态路由，指定优

40、先级为1RoNetwork_Deptip ro 192.168.2.2 255.255.255.255 21.0.0.2 -采用默认的优先级60，比上一条的优先级低RoNetwork_Deptdis ip roDestinations : 21 Routes : 21Destination/Mask Proto Pre Cost NextHop Interface0.0.0.0/32 Direct 0 0 127.0.0.1 InLoop012.0.0.0/24 Direct 0 0 12.0.0.1 GE0/012.0.0.0/32 Direct 0 0 12.0.0.1 GE0/012.0

41、.0.1/32 Direct 0 0 127.0.0.1 InLoop012.0.0.255/32 Direct 0 0 12.0.0.1 GE0/021.0.0.0/24 Direct 0 0 21.0.0.1 GE0/121.0.0.0/32 Direct 0 0 21.0.0.1 GE0/121.0.0.1/32 Direct 0 0 127.0.0.1 InLoop021.0.0.255/32 Direct 0 0 21.0.0.1 GE0/1127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0127.0.0.0/32 Direct 0 0 127.0.0.

42、1 InLoop0127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0127.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0192.168.1.0/24 Direct 0 0 192.168.1.1 Loop0192.168.1.0/32 Direct 0 0 192.168.1.1 Loop0192.168.1.1/32 Direct 0 0 127.0.0.1 InLoop0192.168.1.255/32 Direct 0 0 192.168.1.1 Loop0192.168.2.2/32 Static 1 0 12.

43、0.0.2 GE0/0-只显示高优先级的路由，出口G0/0224.0.0.0/4 Direct 0 0 0.0.0.0 NULL0224.0.0.0/24 Direct 0 0 0.0.0.0 NULL0255.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0RoNetwork_Deptdis ip ro 192.168.2.2Summary Count : 1Destination/Mask Proto Pre Cost NextHop Interface192.168.2.2/32 Static 1 0 12.0.0.2 GE0/0RoNetwork_

44、Deptint g0/0RoNetwork_Dept-GigabitEthernet0/0sh再次关闭G0/0接口，看看路由表的变化RoNetwork_Dept-GigabitEthernet0/0%Aug 22 12:24:56:174 2014 RoNetwork_Dept IFNET/3/PHY_UPDOWN: Physical state on the interface GigabitEthernet0/0 changed to down.%Aug 22 12:24:56:177 2014 RoNetwork_Dept IFNET/5/LINK_UPDOWN: Line protoc

45、ol state on the interface GigabitEthernet0/0 changed to down.RoNetwork_Dept-GigabitEthernet0/0dis ip roDestinations : 17 Routes : 17Destination/Mask Proto Pre Cost NextHop Interface0.0.0.0/32 Direct 0 0 127.0.0.1 InLoop021.0.0.0/24 Direct 0 0 21.0.0.1 GE0/121.0.0.0/32 Direct 0 0 21.0.0.1 GE0/121.0.0

46、.1/32 Direct 0 0 127.0.0.1 InLoop021.0.0.255/32 Direct 0 0 21.0.0.1 GE0/1127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0127.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0127.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0192.168.1.0/24 Direct 0 0 192.168.1.1 Loop0192.168.1.0/32

47、Direct 0 0 192.168.1.1 Loop0192.168.1.1/32 Direct 0 0 127.0.0.1 InLoop0192.168.1.255/32 Direct 0 0 192.168.1.1 Loop0192.168.2.2/32 Static 60 0 21.0.0.2 GE0/1-高优先级的路由不可用后，自动使用低优先级的224.0.0.0/4 Direct 0 0 0.0.0.0 NULL0224.0.0.0/24 Direct 0 0 0.0.0.0 NULL0255.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0R

48、oNetwork_Dept-GigabitEthernet0/0dis ip ro 192.168.2.2Summary Count : 1Destination/Mask Proto Pre Cost NextHop Interface192.168.2.2/32 Static 60 0 21.0.0.2 GE0/1小结：等价静态路由和非等价静态路由都能提供冗余，确保在一条链路出现故障后仍能保持网络的连通性，但是两者存在差别，等价静态路由除了提供冗余外，还能提供负载均衡，数据包会被平均在两条链路上传输，而非等价静态路由中只有高优先级（低代价）的路由是活动的，只有这条路由因为链路故障或接口关闭

49、等原因导致不可用时，低优先级（高代价）的路由才会被启用。等价静态路由适用于存在多条带宽相同的链路的情况，而非等价静态路由适用于存在多条带宽不同的链路的情况尤其是存在主链路和备份链路的情况。7、配置默认路由拓扑图：RoNetwork_Dept端：sysSystem View: return to User View with Ctrl+Z.H3Csysn RoNetwork_DeptRoNetwork_Deptint lo0RoNetwork_Dept-LoopBack0ip add 192.168.1.1 255.255.255.255RoNetwork_Dept-LoopBack0int g

50、0/0RoNetwork_Dept-GigabitEthernet0/0ip add 12.0.0.1 255.255.255.0RoNetwork_Dept-GigabitEthernet0/0undo shRoNetwork_Dept-GigabitEthernet0/0quitRoNetwork_Deptip ro 0.0.0.0 0.0.0.0 12.0.0.2RoNetwork_Deptdis ip roDestinations : 14 Routes : 14Destination/Mask Proto Pre Cost NextHop Interface0.0.0.0/0 Sta

51、tic 60 0 12.0.0.2 GE0/00.0.0.0/32 Direct 0 0 127.0.0.1 InLoop012.0.0.0/24 Direct 0 0 12.0.0.1 GE0/012.0.0.0/32 Direct 0 0 12.0.0.1 GE0/012.0.0.1/32 Direct 0 0 127.0.0.1 InLoop012.0.0.255/32 Direct 0 0 12.0.0.1 GE0/0127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0127.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0127.255.255.255/32 Direct 0 0 127.0.0.