Besam Automated Entrance Systems Inc.docx

《Besam Automated Entrance Systems Inc.docx》由会员分享，可在线阅读，更多相关《Besam Automated Entrance Systems Inc.docx（10页珍藏版）》请在装配图网上搜索。

1、Besam UniSlide Sliding Door SeriesBesam Entrance SolutionsJune 20071900 Airport RoadMonroe, NC28110Toll Free(866) BESAM-US (866-237-2687)Phone(704) 290-5520Fax(704) 290-5555Web SiteE-MailProduct Guide SpecificationSpecifier Notes: This product guide specification is written according to the Construc

2、tion Specifications Institute (CSI) 3-Part Format, including MasterFormat, SectionFormat, and PageFormat, contained in the CSI Manual of Practice.The section must be carefully reviewed and edited by the Architect to meet the requirements of the project and local building code. Coordinate this sectio

3、n with other specification sections and the drawings.Delete all Specifier Notes when editing this section.SECTION 08460AUTOMATIC SLIDING DOORSSpecifier Notes: This section covers Besam UniSlideTM” automatic sliding doors with overhead- concealed and surface-applied, electro-mechanical, microprocesso

4、r-controlled operator and motion/presence sensor control device. If necessary, consult Besam for assistance in editing this section for the specific application.PART 1 GENERALSECTION INCLUDESA. Automatic sliding doors with operator and motion/presence sensor control device.1.1 RELATED SECTIONSSpecif

5、ier Notes: Edit the following list of related sections as required for the project. List other sections with work directly related to this section.A. Section 08410- Aluminum-Framed Storefronts.B. Section 08700- Hardware.C. Section 08800- Glazing.D. Section 16000- Electrical.1.2 REFERENCESBefore plac

6、ing doors in operation, AAADM certified technician shall inspect and approve doors for compliance with ANSI/BHMA 156.10-2005. Certified technician shall be approved and trained by manufacturer.3.5 ADJUSTINGAdjust doors for proper operation in accordance with manufacturers instructions and ANSI/BHMA

7、156.10-2005.3.6 CLEANINGA. Clean doors promptly after installation in accordance with manufacturers instructions.B. Do not use harsh cleaning materials or methods that would damage glass or finish.3.7 PROTECTIONProtect installed doors and finish to ensure that, except for normal weathering, doors an

8、d finish will be without damage or deterioration at time of substantial completion.END OF SECTIONSpecifier Notes: List standards referenced in this section, complete with designations and titles. This article does not require compliance with standards, but is merely a listing of those used.A. ANSI Z

9、97.1 - Safety Glazing Material Used in Buildings.B. ANSI/BHMA 156.10 - Power Operated Pedestrian Doors.C. ANSI/UL 325 - Door, Drapery, Gate, Louver, and Window Operators and Systems.1.3 SYSTEM DESCRIPTIONA. Doors Powered to Open Position:1. Doors powered by DC electric motor and mechanical gear asse

10、mbly transmitted to active leaves by fiberglass-reinforced tooth drive belt for silent operation. Doors using roller chain, cable, or hydraulic devices shall not be accepted.2. Power door to open position by signals received by microprocessor from the actuation controls.3. The last portion of the op

11、ening cycle shall be controlled by a microprocessor generated signal that electronically reduces voltage to motor until door is fully open. Door systems that use microswitches shall not be accepted.4. To permit safe passage if an obstruction is detected between opening doors and surrounding walls or

12、 interior fittings, the doors shall immediately stop and after a delay go to the full closed position. Door systems that only monitor the door travel while closing shall not be acceptable.B. Doors Powered to Closed Position:1. The active leafs will only be powered to closed position when all actuati

13、ng devices are cleared and after remaining in the open position for a preset time delay (per ANS1156.10- 2005 standards).2. The last portion of the closing cycle shall be controlled by a microprocessor generated signal that electronically reduces voltage to the motor until door is fully closed.3. To

14、 permit safe passage between closing doors, the doors immediately reverse to open position if an obstruction is detected, then resume their interrupted movement at low speed to check whether the obstruction has disappeared or not Door systems that only monitor the door travel while opening shall not

15、 be acceptable.C. Emergency Breakaway:Specifier Notes: Specify full breakout system or fixed sidelite system. Consult Besam for additional information.1. Full Breakout System: Interior sliding active leaves and sidelites swing out from any position in sliding mode.2. Fixed Sidelite System: Exterior

16、sliding active leaves swing out from any position in sliding mode.3. Breakaway Pressure: Field adjustable to building code requirements and in accordance with ANSI/BHMA 156.10 maximum of 50 pounds.D. Watchdog Monitoring:1. Microprocessor Software: Constantly monitor drive train system operations.2.

17、Watchdog Control Circuit: Assume command of system and shut down automatic function by holding doors open, should door speed, motor function, or drive train operations deviate from design criteria ranges.3. Secondary Supervisory Circuit: Monitor main Watchdog control circuit every 255 door cycles, r

18、eady to perform as a backup. Door systems that do not monitor control circuits every 255 cycles will not be accepted.E. Energy Saving Device:1. Switch: Recessed in interior header cover.2. Door Opening Settings: Off, exit only, 2-way traffic, partial opening, and hold fully open.3. Partial Opening M

19、ode: Switch reduces total door opening to reduce conditioned air loss.4. Heavy Weather Pile: Between doors and sidelites and between emergency breakaway hardware and door stiles.1.4 PERFORMANCE REQUIREMENTSGeneral: Provide doors that have been designed and fabricated to comply with specified perform

20、ance requirements, as demonstrated by testing manufacturers corresponding standard systems.A. Compliance:1. ANSI/BHMA 156.10.2. ANSI/UL 325 listed.Specifier Notes: Specify UL Canada approved for projects in Canada.3. UL Canada approved.Specifier Notes: For air infiltration compliance, specify per Se

21、ction 2.5.4. Air Infiltration per ASTM E283-91 - Standard Test Method for Determining the Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across Specimen.a. Fixed sidelite: static pressure air infiltration conducted at 0.57 psf (15 mph) wit

22、h a 0.6 cfm/fr result and 1.57 psf (25 mph) with a 1.1 cfm/fT result.b. Full breakout: static pressure air infiltration conducted at 0.57 psf (15 mph) with a .07 cfm/ft/, result and 1.57 psf (25 mph) with a 1.3 cfm/ft, result.Specifier Notes: For structural performance (wind load compliance), specif

23、y per Section 2.6.5. Structural Performance (wind load) per ASTM E330-07 - Standard Test Method for Structural Performance of Exterior Windows, Curtain Walls, Doors by Uniform Static Air Pressure Difference. Testing conducted at positive and negative loads.a. Fixed sidelite: 50 psf (150 mph)Full bre

24、akout: 37 psf (120 mphjSpecifier Notes: For forced entry resistance, specify per Section 2.6.6. Forced Entry Resistance per AAMA 1303.5 - Voluntary Specifications for Forced Entry Resistant Aluminum Sliding Glass Doors.B. Automatic door equipment accommodates medium to heavy pedestrian traffic.C. Au

25、tomatic door equipment accommodates up to following weights for active leaf doors:1. Bi-Part Doors: 220 pounds (100 kg) per active leaf.2. Single Slide Doors: 300 pounds (200 kg) per active leaf.D. Operating Temperature Range: -35 F to 122 F (-30C to 50C).E. Motion and Presence Detection System: Use

26、s planar K-band microwave technology to detect motion and focused active infrared technology to detect presence, in a single housing.F. Systems With Transom Over 16-0 (4,877 mm) or With Heavy Glass: System can span up to 16 feet without overhead support. Systems at 16*-0, with transoms, or with heav

27、y glass shall install anti-sag rods through transom verticals.1.5 SUBMITTALSA. Comply with Section 01330 - Submittal Procedures.B. Product Data: Submit manufacturers product data, including description of materials, components, fabrication, finishes, and installation.C. Shop Drawings: Submit manufac

28、turers shop drawings, including elevations, sections, and details, indicating dimensions, materials, and fabrication of doors, frames, sidelites, operator, motion/presence sensor control device, anchors, hardware, finish, options, and accessories.D. Samples: Submit manufacturers samples of aluminum

29、finishes.E. Test Reports: Submit certified test reports from UL, CUL, and ICBO indicating doors comply with specified performance requirements.F. Manufacturers Project References: Submit list of successfully completed projects including project name and location, name of architect, and type and quan

30、tity of doors manufactured.G. Manufacturers Field Reports: Submit manufacturers field reports from AAADM certified technician of inspection and approval of doors for compliance with ANSI/BHMA 156.10 after completion of installation.H. Operation and Maintenance Manual:1. Submit manufacturers operatio

31、n and maintenance manual.2. Include spare parts list.I. Warranty: Manufacturers standard warranty shall be one year from date of installation.J. Manufacturer must supply any special tools or devices to make adjustments, setup, and / or to service equipment to the owner with the closeout documents at

32、 no additional cost to the owner.1.6 QUALITY ASSURANCEA. Manufacturers Qualifications:1. Continuously engaged in manufacturing of doors of similar type to that specified, with a minimum of 10 years successful experience.2. Member: American Association of Automatic Door Manufacturers (AAADM).3. Door,

33、 frame, operator, and sensor components from same manufacturer.B. Installers Qualifications:1. Minimum of 2 years successful experience in installation of similar doors.2. Local certified Besam distributor.4. Approved by manufacturer.5. AAADM certifiedDELIVERY, STORAGE, AND HANDLINGA. Delivery: Deli

34、ver materials to site protected from damage.B. Storage: Store materials in clean, dry area indoors in accordance with manufacturers instructions.C. Handling: Protect materials and finish from damage during handling and installation.1.7 MAINTENANCE SERVICEThe manufacturer shall offer a dispatch proce

35、dure that shall be available 24 hours per day, 365 days per year to facilitate proper service capability.A. A manufacturers designated service contact shall obtain malfunction information and dispatch appropriate service provider to project location.B. Toll free phone number, 1 -877-BESAM-US (1 -877

36、-237-2687), shall be prominently displayed on header of each operator.C. A geographically assigned installation provider shall be trained and certified to provide maintenance service.PART 2 PRODUCTSMANUFACTURERA. Besam Entrance Solutions, 1900 Airport Road, Monroe, North Carolina 28110. Toll Free (8

37、66) BESAM-US. Phone (704) 290-5520. Fax (704) 290-5555. Web Site . E-Mail .2.1 AUTOMATIC SLIDING DOORSA.1. Model: UniSlide automatic sliding doors.Automatic Sliding Door System: Shall be Besam UniSlide System. The system shall consist of sliding aluminum doors, header, operator, threshold track and

38、actuating controls. The Besam header will include the UltraView Motion and Presence Sensor Control System that is self-monitoring and communicates with the UniSlide through a monitoring connection. The self-monitoring connection allows the door to go into a failsafe mode in the event of a sensor or

39、monitoring failure. Door systems that do not employ a fail-safe self-monitoring system will not be acceptable.Specifier Notes: Specify either overhead-concealed or surface-applied.2. Overhead-concealed surface-applied, electro-mechanical, microprocessor-controlled, sliding door operator.3. Operator

40、housing, floor rollers, and door carriers.A. Dimensions:1. Sliding Aluminum Doors: Provide door units to dimension heights and widths with corresponding stile glazing as shown on construction documents. Glass stops as specified shall be available for all door panels and transom. The bi-part sliding

41、door system shall include a two-point lock securing the lead edges of the door stiles together and to the hanger assembly. All doors shall have horizontal door extrusions, including optional muntins, with the design characteristic to nest or interlock into the intersecting vertical member. This desi

42、gn feature is to restrict any twisting or movement of the horizontal member that can produce open sightlines and / or compromise the door leaf integrity. The door package shall include security ball catches that latch the swing out panels in the closed position when the sliding doors are in the full

43、y closed position. The active sliding door shall be provided with a key cylinder on the exterior and a thumb turn on the interior in accordance with NFPA 101.Specifier Notes: Specify the following dimensions here or provide the dimensions on the drawings.1. Clear Doorway Opening Width: As indicated

44、on the drawings.2. Overall Frame Width: As indicated on the drawings.3. Masonry Opening Width: As indicated on the drawings.4. Active and Sidelite Leaf Width: As indicated on the drawings.5. Clear Door Opening Height: As indicated on the drawings.6. Overall Frame Height: As indicated on the drawings

45、.7. Masonry Opening Height: As indicated on the drawings.8. Active and Sidelite Leaf Height: As indicated on the drawings.2.2 ALUMINUM DOORS AND FRAMESA. Doors and Frames: Extruded aluminum, Alloy 6063-T5.1. Hydraulic dampers (optional): provide 90 degree stop and cushion door upon opening and closi

46、ng during emergency breakout conditions.B. Glass:1. Glazing Material: ANSI Z97.1.Specifier Notes: Specify required glass for active leaves and sidelites. Sidelites with 1-inch (25mm) glass only available with fixed sidelite units.2. Active Leaves: 1/4-inch (6-mm) glass 5/8-inch (16-mm) glass insulat

47、ing units 1-inch (25-mm) glass insulating units.3. Sidelites: 1/4-inch (6-mm) glass 5/8-inch (16-mm) glass insulating units 1-inch (25- mm) glass insulating units 一 fixed sidelite units only.4. Field-glazed or preglazed.C. Door Operation:1. Shall be Besam UniSlide Door System with UltraView Technolo

48、gy for bi-part or single slide directional operation. In compliance with NFPA 101, all panels shall allow “breakout to the full open position to provide instant egress at any point in the doors movement. To allow safe egress, automatic operation shall be discontinued when any panels are in the break

49、out* mode. Doors and sidelights shall be sized to prevent pinch points at meeting stiles.D. Aluminum Frame and Extrusions:1. Shall be a consistent .125” wall thickness throughout the entire extruded member including and not exclusive to, the integral structural sections to maintain the integrity of

50、the overall extruded shape. Glass stops shall have .062-wall thickness. Door systems with less than .125 wall thickness or with .125 nominal” thicknesses will not be accepted.E. Sidelites:1. Provide sidelites to dimension heights and widths as shown on construction documents with corresponding glazi

51、ng. All sidelights shall have interlocking, nested intermediate rails to prevent twisting and separation. The sidelights shall swing out and allow the sliding doors to “breakout” to the full open position for instant egress at any point in the doors movement per NFPA 101.F. Header Case:1. Shall be a

52、 Besam 7-5/8” x 6-7/8” architecturally enhanced extruded aluminum profile with recessed UltraView sensors on each side to meet ANSI A156.10-05. Header shall be capable of supporting bi-parting doors of 220 pounds per leaf over a span of 16-0” without intermediate supports when using glass. It shall

53、contain door operator and door mounting components. The header shall be a “closed design* to reduce infiltration of airborne contaminants and debris which may inhibit proper operation and facilitate increased service requirements. Headers with visible underside carrier openings of or greater, whethe

54、r in the open or closed positions, shall not be accepted.G. Roller Composition:1. Shall consist of two (2) steel roller wheels per door leaf having a 1 -3/4 (44mm) diameter with single journal sealed oil-impregnated bearings to ensure roller life on a replaceable Delrin track to reduce service cost

55、from normal usage and incorporate self-aligning antirisers to ensure proper panel positioning. Rollers of any urethane composition shall not be accepted. The assembly shall allow the sliding doors to swing outward and facilitate emergency egress in accordance with NFPA 101.Specifier Notes: Specify d

56、oor stile width.G. Stiles: Narrow - 2-1/8 Medium - 4 Wide - 5.H. Pivots: Top and bottom concealed pivots, extruded aluminum.I. Hardware: Breakaway.J. Exterior Glazing Stop Extrusion: Nonremovable, security-type glazing bead to prevent unauthorized entry. Doors utilizing removable exterior stops will

57、 not be accepted.2.3 SLIDING DOOR OPERATIONA. Door Operator and Controller:1. Shall be a Besam electro-mechanical controlled unit. The operator shall integrate a high- efficiency, energy efficient, DC motor requiring a minimum of 3 A current draw, allowing 5 door systems on one 20 A circuit. The sup

58、plied system shall have the capability to operate at full performance well beyond a brown out and high line voltage conditions (85V 一 265V) sensing changes and adjusting automatically. The operator shall be of the type to allow an adjustable hold open time delay of 0 to 60 second having internal sof

59、tware to incorporate a self-diagnostic system.B. Microprocessor Control Box:1. Besam factory-adjusted configuration, with opening and closing speeds set to comply with ANSI A156.10-2005 requirements. Should the drive train operations deviate from design criteria ranges, Watchdog Control Circuit Moni

60、toring will assume command of the system and shut down the automatic function allowing a secondary supervisory circuit to perform as a backup.E Accessories:1. The UniSlide Automatic Sliding Door System shall have the following accessories to reduce energy loss: Adjustable nylon sweep(s) on the botto

61、m of the sliding door(s), double pile weather stripping for the sliding door lead edges, single pile weather stripping between the carrier and the header on the lead stile(s) of the sidelight(s) and the pivot stile(s) of the sliding door(s), and a selector switch located on the interior side of the

62、unit to allow door(s) to open at full or reduced width according to weather and traffic conditions.2.4 AIR INFILTRATION (OPTIONAL)Weatherstripping: All active door panel weatherstripping shall be concealed, finned-pile.”STRUCTURAL PERFORMANCE (WIND LOAD COMPLIANCE) AND FORCED ENTRY RESISTANCE (OPTIO

63、NAL)A. Locking shall be independent 2 pt- locking system in each active leaf and include exterior key cylinder and interior thumb turn.B. Threshold shall be aluminum, V2 x 4-1/2 running full width of package. Lead-up: optional.2.5 MOTION AND PRESENCE SENSOR CONTROL DEVICEA. Model: The Besam UltraVie

64、wThe focused active infrared shall be used for the purpose of presence detection in and around the door threshold area. The presence technology shall overlap the motion pattern. The active infrared is comprised of 96 spots of detection made out of four rows of 24 spots of detection each (two rows on

65、 each side of the door). The system is built on numerous object-tracking algorithms. Any object is tracked while in the infrared presence zone as well as in the threshold area. The focused active infrared (safety zone) remains active even during the closing cycle of the door to EXCEED guidelines as outlined in ANSI A156.10- 2005.Sensors not using focused active infrar