路由交换技术--综合组网课程设计

《路由交换技术--综合组网课程设计》由会员分享，可在线阅读，更多相关《路由交换技术--综合组网课程设计（4页珍藏版）》请在装配图网上搜索。

1、1. 拓扑图：2. 配置OSPF(1) Router0Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 0.255.255.255 area 0Router(config-router)#network 2.1.1.0 0.0.0.255 area 0Router(config-router)#network 192.168.3.0 0.0.0.255 area 0(2) Router1Router(config)#router ospf 1Router(config-router)#network 2.1.1

2、.0 0.0.0.255 area 0Router(config-router)#network 11.0.0.0 0.255.255.255 area 0Router(config-router)#network 192.168.2.0 0.0.0.255 area 0(3) Router2Router(config)#router ospf 1Router(config-router)#network 11.0.0.0 0.255.255.255 area 0Router(config-router)#network 172.16.0.0 0.0.255.255 area 0Router(

3、config-router)#network 192.168.1.0 0.0.0.255 area 0(4) Router3Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 0.255.255.255 area 0Router(config-router)#network 172.16.0.0 0.0.255.255 area 0(5)测试从Router0 ping Router 2Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 1

4、72.16.0.1, timeout is 2 seconds:!Success rate is 100 percent (5/5), round-trip min/avg/max = 62/62/63 ms(6) 从Router 1 ping Router 3Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 10.0.0.2, timeout is 2 seconds:!Success rate is 100 percent (5/5), round-trip min/avg/max = 47/53/63 ms3.

5、 配置PPP PAP双向认证（Router0、Router1）Router0配置：Router(config)#username 123 password 456Router(config)#inter s1/0Router(config-if)#encapsulation pppRouter(config-if)#ppp authentication papRouter(config-if)#ppp pap sent-username 111 password 222Router1配置Router(config)#username 111 password 222Router(config)

6、#inter s1/0Router(config-if)#encapsulation pppRouter(config-if)#ppp authentication papRouter(config-if)#ppp pap sent-username 123 password 4564. 配置DLCI帧中继Router3配置Router(config)#inter s1/0Router(config-if)#no ip addressRouter(config-if)#encapsulation frame-relayRouter(config-if)#inter s1/0.1 multipo

7、intRouter(config-subif)#frame-relay map ip 192.168.4.2 502 broadcast Router(config)#inter s1/0.2 point-to-point Router(config-subif)#frame-relay interface-dlci 504Router4、Router5配置Router(config)#inter s1/0Router(config-if)#encapsulation frame-relay Router(config)#inter s1/0Router(config-if)#encapsul

8、ation frame-relay 帧中继配置测试从Router3 ping Router4和Router5Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 192.168.4.2, timeout is 2 seconds:!Success rate is 100 percent (5/5), round-trip min/avg/max = 47/59/63 msType escape sequence to abort.Sending 5, 100-byte ICMP Echos to 192.168.5.2,

9、 timeout is 2 seconds:.!Success rate is 80 percent (4/5), round-trip min/avg/max = 46/55/63 ms5.DHCP：1.为本地网段PC动态分配网络参数，FTP服务器动态分配固定地址2.为外部网段动态分配网络参数Router6配置如下：Router(config)#ip dhcp pool 1Router(dhcp-config)#exitRouter(config)#ip dhcp pool 2FTP服务器获取成功PC2PC36. Router1作为vlan间路由，switch0作为VTP服务器，PC0和PC

10、1通过Router6获得IP地址Router1：Router(config-if)#inter f0/0.2Router(config-subif)#encapsulation dot1Q 2Router(config-subif)#no shutRouter(config-subif)#inter f0/0.3Router(config-subif)#encapsulation dot1Q 3Router(config-subif)#no shutRouter(config)#ip forward-protocol udpRouter(config)#inter f0/0.2Router(c

11、onfig-subif)#inter f0/0.3Router(config-subif)#ip helpSwitch0：Switch(config)#vlan 2Switch(config-vlan)#exitSwitch(config)#vlan 3Switch(config-vlan)#exitSwitch(config)#inter f0/1Switch(config-if)#switchport mode trunk Switch(config)#inter f0/2Switch(config-if)#switchport mode trunk Switch(config-if)#i

12、nter f0/3Switch(config-if)#switchport mode trunk Switch1：Switch(config)#inter f0/1Switch(config-if)#switchport mode trunk Switch(config-if)#inter f0/2Switch(config-if)#switchport mode trunk Switch(config-if)#inter f0/3Switch(config-if)#switchport access vlan 2Switch2：Switch(config)#inter f0/1Switch(

13、config-if)#switchport mode trunk Switch(config-if)#inter f0/2Switch(config-if)#switchport mode trunk Switch(config-if)#inter f0/3Switch(config-if)#switchport access vlan 3Router6：Router(config)#ip dhcp pool 3PC1：PC0：8. 在Router2上配置内部源地址动态转换Router(config)#ip nat inside source list 1 pool pool1Router(c

14、onfig)#inter f1/0Router(config-if)#ip nat insideRouter(config-if)#inter f0/1Router(config-if)#ip nat outside以172.16.0.0作为外部网段由R6 telnet到R3Trying 172.16.0.2 .OpenUser Access VerificationPassword: RouterR3结果：172.16.0.10为R6上192.168.1.2转换以后的IP地址。9.ACL:通过域名访问WEB服务器192.168.1.0可以访问192.168.2.0不可以访问Router(config)#access-list 102 deny tcp 192.168.2.0 0.0.0.255 any eq 80Router(config)#access-list 102 permit tcp 192.168.1.0 0.0.0.255 any eq 80Router(config-if)#ip access-group 102 outPC2可以访问WEBPC0不能访问