汽车英语专业词汇完全篇

《汽车英语专业词汇完全篇》由会员分享，可在线阅读，更多相关《汽车英语专业词汇完全篇（132页珍藏版）》请在装配图网上搜索。

1、底盘平移台 chassis shuttle 车辆转移台 bus transfer 前围角板 front wall angle cover 后围侧板 rear wall side cover 保险杠 bumper 三类底盘 three type chassis 左侧围应力蒙皮 R/S stretching skin (road side) 中涂 floating coat 拼装台 collector 切割轮口 wheel -arch cutting 内饰 trim 线束 harness 返工 re-doing 轮罩护板 wheel house 发车前准备 pre-delivery 举升 hois

2、t 小批量产品 be pilot 2 套 two kits 配电站 power transformer substation 裙板 skirt 发动机托架 engine holding frame 诊断报警系统 diagnosis and alarming system 互换性 interchangeability 缩微图纸 microfiche files 总装 final assembly 磷化 phosphate 仪表板 dash board 切齐 trimming 结构完整性 structure integrity 自动愈合的防腐材料 self-healing corrosion pr

3、eventative material 长途客车 inter-city bus 改装厂 refitting factory 遮阳板 sun visor 随车工具 tool box 钢化玻璃 toughened grass 异形钢管 special steel pipe 全天候空调系统 full range A/C 强制通风 ram-air ventilation 停机时间 downtime 无公害柴油 clean diesel 宽敞悬臂式座椅 roomy cantilevered seat 防滑地板 no-skid floor 织物纹里铝合金 textured aluminum extrusi

4、on 爬坡能力 grade ability 排水阀 drain valve 除湿器 moisture ejector 怠速时 at idle 琴式驱动桥 banjo type drive axle 通风口 duct 恒温控制 thermostatic control 平衡水箱 surge tank 变光开关 simmer switch 消音器 muffler 防破坏 vandal resistant 聚碳化透镜 poly-carbonate Len 镀锌板 galvanized plate 搭接 lap 亮丽的外表 smart appearance 隐藏式固定 concealed fasten

5、ing 水洼 pending 发动机中置式客车 bus with under floor engine 组合式客车车身 modular bus body 薄壳式结构 shell construction 衬垫 pad 空气导流板 air deflector 搁梁 shelf beam 腰梁 waist rail 梭梁 stabilizing beam 腰带式安全带 diagonal safety belt 压条 trim strip 嵌条 insertion strip 翼板 fender 斜撑 bracing piece 转向盘回正性试验 test of steering wheel ret

6、urn ability转向盘转角脉冲试验 steering wheel impulse input test转向盘转角阶跃输入试验 steering wheel step input or transient state yaw response test极限侧向加速度试验 limiting lateral acceleration test汽车平顺性随机输入行驶试验 automobile ride random input running test汽车平顺性单脉冲输入行驶试验 automobile ride single pulse input running test汽车悬挂系统固有频率与

7、阻尼比的测定试验 measurement of natural frequency and damping ratio of suspension功率突然变化影响试验 test of effect of sudden power change收油门后控制试验 test of control at breakaway横风稳定性试验 test of crosswind stability反冲试验 kick-back test轮胎爆破响应时间试验 test of burst response of tire绕过障碍物试验 obstacle avoidance test移线试验 lane change

8、 testJ型转弯试验 test of J turn频率响应时间试验 frequency response test瞬态响应时间试验 transient response test阶路响应时间试验 step response test脉冲响应试验 pulse response test静态操舵力试验 static steering effort test悬架举升试验 jack-up test of suspension耐翻倾试验 test of overturning immunity轮辋错动试验 rim slip test风洞试验 wind tunnel test制动稳定性试验 test o

9、f braking stability最小转弯直径试验 minimum turning diameter test操舵力试验 steering effort test类型 type发动机 engine内燃机 internal combustion engine动力机装置 power unit汽油机 gasoline engine汽油喷射式汽油机 gasoline-injection engine火花点火式发动机 spark ignition engine压燃式发动机 compression ignition engine往复式内燃机 reciprocating internal combust

10、ion engine化油器式发动机 carburetor engine柴油机 diesel engine转子发动机 rotary engine旋轮线转子发动机 rotary trochoidal engine二冲程发动机 two-stroke engine四冲程发动机 four-stroke engine直接喷射式柴油机 direct injection engine间接喷射式柴油机 indirect injection engine增压式发动机 supercharged engine风冷式发动机 air-cooled engine油冷式发动机 oil-cooled engine水冷式发动机

11、water-cooled engine自然进气式发动机 naturally aspirated engine煤气机 gas engine液化石油气发动机 liquified petroleum gas engine柴油煤气机 diesel gas engine多种燃料发动机 multifuel engine石油发动机 hydrocarbon engine双燃料发动机 duel fuel engine热球式发动机 hot bulb engine多气缸发动机 multiple cylinder engine对置活塞发动机 opposed piston engine对置气缸式发动机 opposed-

12、cylinder engine十字头型发动机 cross head engine直列式发动机 in-line engine星型发动机 radial engine筒状活塞发动机 trunk-piston engine斯特林发动机 stirling engine套阀式发动机 knight engine气孔扫气式发动机 port-scavenged engine倾斜式发动机 slant engine前置式发动机 front-engine后置式发动机 rear-engine中置式发动机 central engine左侧发动机 left-hand engine右侧发动机 right-hand engin

13、e短冲程发动机 oversquare engine长冲程发动机 undersquare engine等径程发动机 square engine顶置凸轮轴发动机 overhead camshaft engine双顶置凸轮轴发动机 dual overhead camshaft engineV形发动机 V-engine顶置气门发动机 valve in-head engine侧置气门发动机 side valve engine无气门发动机 valveless engine多气门发动机 multi-valve engine卧式发动机 horizontal engine斜置式发动机 inclined engi

14、ne立式发动机 vertical engineW形发动机 w-engineI形发动机 I-engineL形发动机 L-engineF形发动机 F-engine性能 performance二冲程循环 two-stroke cycle四冲程循环 four-stroke cycle狄塞尔循环 diesel cycle奥托循环 otto cycle混合循环 mixed cycle定容循环 constant volume cycle工作循环 working cycle等压循环 constant pressure cycle理想循环 ideal cycle热力循环 thermodynamic cycle冲

15、程 stroke活塞行程 piston stroke长行程 long stroke上行程 up stroke下行程 down stroke进气行程 intake stroke充气行程 charging stroke压缩行程 compression stroke爆炸行程 explosion stroke膨胀行程 expansion stroke动力行程 power stroke排气行程 exhaust stroke膨胀换气行程 expansion-exchange stroke换气压缩行程 exchange-compression stroke止点 dead center上止点 top dead

16、 center(upper dead center)下止点 lower dead center(bottom dead center)上止点前 budc(before upper dead center)上止点后 atdc(after top dead cetner)下止点前 bbdc(before bottom dead center)下止点后 abdc(after bottom dead center)缸径 cylinder bore缸径与行程 bore and stroke空气室 energy chamber气缸余隙容积 cylinder clearance volume燃烧室容积 co

17、mbustion chamber volume气缸最大容积 maximum cylinder volume压缩室 compression chamber排气量 displacement发动机排量 engine displacement活塞排量 piston swept volume气缸容量 cylinder capacity单室容量 single-chamber capacity容积法 volumetry压缩比 compression ratio临界压缩比 critical compression ratio膨胀比 expansion ratio面容比 surface to volume ra

18、tio行程缸径比 stroke-bore ratio混合比 mixture ratio压缩压力 compression pressure制动平均有效压力 brake mean effective pressure(bmep)空燃比 air fuel ratio燃空比 fuel air ratio燃料当量比 fuel equivalence ratio扭矩 torque单缸功率 power per cylinder升功率 power per liter升扭矩 torque per liter升质量 mass per liter 减额功率 derating power输出马力 shaft hors

19、epower马力小时，马力时 horsepower-hour总马力 gross horse power总功率 gross power 净功率 net power 燃油消耗量 fuel consumption 比燃料消耗率 specific fuel consumption空气消耗率 air consumption机油消耗量 oil consumption有效马力 net horse power额定马力 rated horse power马力重量系数 horsepower-weight factor制动功率 brake horse power制动热效率 brake thermal efficie

20、ncy 总效率 overall efficiency排烟极限功率 smoke limiting horsepower功率曲线 power curve机械损失 mechanical loss机械效率 mechanical efficiency有效热效率 effective thermal efficiency充气系数 volumetric efficiency过量空气系数 coefficient of excess air适应性系数 adaptive coefficient扭矩适应性系数 coefficient of torque adaptibility转速适应性系数 speed adapti

21、ve coefficient强化系数 coefficient of intensification校正系数 correction factor换算系数 conversion factor活塞平均速度 mean piston speed发动机转速 engine speed (rotational frequency)怠速转速 idling speed经济转速 economic speed起动转速 starting speed最低稳定工作转速 lowest continuous speed with load最大扭矩转速 speed at maximum torque最高空转转速 maximum

22、no load governed speed调速 speed governing 超速 overspeed怠速 idling转速波动率 speed fluctuation rate工况 working condition(operating mode)额定工况 declared working condition变工况 variable working condition稳定工况 steady working condition空载 no-load全负荷 full load超负荷 overload部分负荷 part load充量（进气）charge旋转方向 direction of rotat

23、ion顺时针 clockwise逆时针 counter-clockwise左转 left-hand rotation右转 right-hand rotation外径 major diameter中径 pitch diameter内径 minor diameter径向间隙 radial clearance发动机性能 engine performance加载性能 loading performance起动性能 starting performance加速性能 acceleration performance动力性能 power performance排放性能 emission performanc

24、e空转特性 no load characteristics负荷特性 part throttle characteristics调速特性 governor control characteristics万有特性 mapping characteristics稳定调速率 steady state speed governing rate气缸体和气缸盖 cylinder block and head气缸体 cylinder block整体铸造 cast inblock (cast enblock)发动机罩 engine bonnet气缸体加强筋 engine block stiffening rib

25、气缸 cylinder（转子机）缸体 stator缸径 cylinder bore气缸体机架 cylinder block frame气缸盖 cylinder head配气机构箱 valve mechanism casing气缸体隔片 cylinder spacer气缸盖密封环 cylinder head ring gasket气缸盖垫片 cylinder head gasket气缸套 cylinder liner(cylinder sleeve)干式缸套 dry cylinder liner湿式缸套 wet cylinder liner气缸水套 water jacket膨胀塞 expansi

26、on plug防冻塞 freeze plug气缸壁 cylinder wall环脊 ring ridge排气口 exhaust port中间隔板 intermediate bottum导板 guideway创成半径（转子机）generating radius缸体宽度（转子机）operating width机柱 column燃烧室 combustion chamber主燃烧室 main combustion chamber副燃烧室 subsidiary combustion chamber预燃室 prechamber涡流燃烧室 swirl combustion chamber分开式燃烧室 div

27、ided combustion chamber涡流式燃烧室 turbulence combustion chamber半球形燃烧室 hemispherical combustion chamber浴盆形燃烧室 bathtub section combustion chamberL形燃烧室 L-combustion chamber楔形燃烧室 wedge-section combustion chamber开式燃烧室 open combustion chamber封闭喷射室 closed spray chamber活塞顶内燃烧室 piston chamber爆发室 explosion chambe

28、r燃烧室容积比 volume ratio of combustion cahmber燃烧室口径比 surface-volume ratio of combustion chamber通道面积比 area ratio of combustion chamber passage曲轴箱通气口 crankcase breather凸轮轴轴承座 camshaft bearing bush seat定时齿轮室罩 camshaft drive(gear)cover曲轴箱检查孔盖 crankcase door曲轴箱防爆门 crankcase explosion proof door主轴承盖 main bear

29、ing cap气缸盖罩 valve mechanism cover飞轮壳 flywheel cover扫气储器 scavenging air receiver活塞 piston裙部开槽活塞 split skirt pistonU形槽活塞 U-slot piston滚花修复活塞 knurled piston圆顶活塞 dome head piston平顶活塞 flat head piston凸顶活塞 crown head piston(convex head piston)凹顶活塞 concave head piston阶梯顶活塞 step-head piston筒形活塞 trunk piston

30、椭圆形活塞 oval piston抗热变形活塞 autothermic piston不变间隙活塞 constant clearance piston镶因瓦钢片活塞 invar strut piston直接冷却式活塞 direct-cooled piston间接冷却式活塞 indirect cooled piston滑裙活塞 slipper piston活塞速度 piston speed活塞顶部 piston head活塞裙部 piston skirt整体活塞裙 solid skirt活塞裙扩大衬簧 piston skirt expander滑履式活塞裙 slipper skirt隔热槽 hea

31、t dam活塞标记 piston mark活塞销 piston pin活塞销孔 piston pin boss活塞销衬套 piston pin bushing全浮式活塞销 full-floating piston pin半浮式活塞销 semifloating piston pin固定螺钉式活塞销 set screw piston pin活塞环 piston ring组合式活塞环 compound piston ring同心活塞环 concentric piston ring偏心活塞环 eccentric piston ring自由环 free ring闭合环 closed ring梯形环 ke

32、ystone ring半梯形环 half keystone ring矩形环 rectangular ring油环 oil control ring开槽油环 slotted oil control ring螺旋弹簧加载双坡口油环 coil spring loaded slotted oil control ring 涨环 expander双坡口油环 double bevelled oil control ring内上坡口 internal bevel top内下坡口 internal bevel bottom边缘坡口油环 bevelled-ege oil control ring刮油环 scra

33、pper ring钩形环 napier ring镀铬活塞环 chrome plated piston ring活塞衬环 piston ring expander活塞环槽 piston ring groove活塞环区 ring zone活塞环岸 piston ring land活塞环内表面 back of ring曲柄连杆机构 connecting rod中心曲柄连杆机构 central-located connecting rod偏心曲柄连杆机构 offset connecting rod铰接曲柄边杆机构 hinged connecting rod连杆 connecting rod连杆小头 c

34、onnecting rod small end连杆大头 connnecting rod big end连杆杆身 connecting rod shank副连杆 slave connecting rod叉形连杆 fork-and-blade connecting rod主连杆 main connecting rod方形连杆 boxed rod绞链式连杆 hinged type connecting rod活节式连杆 articulated connecting rod连杆盖 connecting rod cap连杆轴承 connecting rod bearing曲轴 crankshaft整体式

35、曲轴 one-piece crankshaft组合式曲轴 assembled crankshaft右侧曲轴 right-hand crankshaft左侧曲轴 left-hand crankshaft改变行程的曲轴 stroked crankshaft曲轴前端 crankshaft front end曲轴主轴颈 crankshaft main journal 轴颈重叠度 shaft journal overlap圆角 fillet主轴承 main bearing曲轴止推轴承 crankshaft thrust bearing薄臂轴瓦 thin wall bearing shell曲轴油道 cr

36、ankshaft oil passage曲柄 crank曲柄臂 crank arm曲柄销 crank pin轴套 bush曲柄转角 crank angle曲柄半径 crank radius抛油圈 oil slander角度轮 degree wheel 动平衡机 dynamic balancer平衡重 balancer weight扭振减振器 torshional vibration damper扭振平衡器 torsion balancer谐振平衡器 harmonic balancer振动平衡器 vibration balancer曲轴链轮 crankshaft sprocket转子轴颈 rot

37、or journal 偏心轴 eccentric shaft曲轴箱 crankcase闭式曲轴箱通风装置 closed-crankcase ventilating system飞轮 flywheel飞轮齿圈 flywheel ring gear飞轮芯棒 cantilever飞轮芯轴 flywheel spindle飞轮的惯量矩 flywheel moment of inertia飞轮标记 flywheel mark当量系统 equivalent system当量轴长 equivalent shaft length一级往复惯性力 reciprocating inertia force,1st o

38、rder二级往复贯性力 reciprocating inertia force, 2nd order离心惯性力 centrifugal inertia force配气机构 valve gear凸轮轴 camshaft凸轮 cam整体式凸轮轴 one-piece camshaft组合式凸轮轴 assembled camshaft凸轮轴驱动机构 camshaft drive赛车用凸轮轴 race camshaft凸轮轴轴颈 camshaft bearing journal凸轮轴轴承 camshaft bearing 凸轮轴偏心轮 camshaft eccentric凸轮轴链轮 camshaft s

39、procket凸轮轴正时齿轮 camshaft timing gear凸轮轴齿轮 camshaft gear wheel 进口凸轮 inlet cam排气凸轮 exhaust cam快升凸轮 quick lift cam快升缓降凸轮 quick lift gradual clsing cam凸轮轮廓 cam contour凸轮包角 cam angle凸轮升程 cam-lobe lift凸轮尖 cam nose凸轮从动件 cam follower齿轮传动机构 gear drive正时齿轮 timing gear链传动机构 chain drive链轮 sprocket wheel 链轮盘 chai

40、n sprocket正时链条 timing chain带齿皮带 toothed timing belt链条张紧轮 chain tension gear半速齿轮 half speed gear正时齿轮刻印记号 timing gear punch mark气门 valve进气过程 intake process换气过程 gas exchange process扫气过程 scavenging process给气比 delivery ratio分层充气 stratified charge充量系数 volumetric efficiency涡流比 swirl rate进气涡流 intake swirl螺旋

41、进气道进气 helical duct intake导流屏式气门进气 masked valve intake切向进气道进气 tangential duct intake进气紊流 intake trubulence进气提前角 intake advance angle进气持续角 intake duration angle进气迟后角 intake lag angle进面值 time-area value气门升程 valve lift气门正时 valve timing扫气口面积 scavenging port area菌形气门 mashroom valve, poppet valve钠冷却气门 sodi

42、um filled valve(natrium cooled valve)双气门 dual valve进气门 intake valve (suction valve,inlet valve)排气门 exhaust valve顶置气门 overhead valve侧置气门 side valve倾斜气门 inclined overhead valve直立气门 vertical overhead valve套筒式滑阀 sleeve valve气门机构 valve gear直接式气门驱动机构 direct valve gear间接式气门驱动机构 indirect valve gear气门杆 valve

43、 stem加大气门杆 oversize valve stem气门头 valve head气门工作面 valve face气门边限 valve margin气门弹簧座 valve-spring retainer气门锁片 valve key气门间隙调节螺钉 valve lash adjusting screw气门旋转器 valve rotator气门室 valve cage气门油封 valve oil seal气门口 valve port气门座 valve seat气门座镶圈（嵌镶式气门座圈） valve seat insert(valve seat ring)气门座锥角 valve seat a

44、ngle气门座宽度 valve seat width气门挺杆 valve tappet(valve lifter)液力挺杆 hydraulic tappet(lifter)无间隙挺杆 zero-rush tappet (non-clearance tappet)筒形挺杆 barrel type tappet油压挺杆 ooil tappet滚轮挺杆 roller tappet(lifter)挺杆转位 tappet rotation 排气门挺杆 exhaust valve lifter气门导管 valve guide气门杆导管 stem guide气门重叠度 stem overlap气门开启持续时

45、间 valve duration 气门正时标记 valve timing sign气门弹簧 valve spring气门内弹簧 inner valve spring气门外弹簧 outer valve spring刚性缓冲弹簧 stiff buffer spring上紧弹簧 energizing spring防振气门弹簧 non-surging spring弹簧座圈 spring retainer蝶形弹簧 belleville spring滚柱 roller 气门室盖 valve chamber cover摇臂 rocker arm高升程摇臂 high lift rocker arm摇臂轴 ro

46、cker arm shaft推杆 push-rod摇臂支架 rocker arm bracket气门摇臂室罩 valve rocker chamber cover导向轮 guide wheel 导杆 slide bar导轨 slide rail张紧轮 tensioning wheel链条张紧调节装置 assembly chain tension adjuster张紧带轮 tensioning pulley传动带张紧装置 belt tensioner同步驱动皮带 synchronous belt同步驱动皮轮 synchronous belt pulley供油系 fuel system控制燃烧系统

47、 controlled combustion system反湿气装置 antipercolator电子燃油喷射 electronic fuel injection 蒸气回收装置 vapor recovery system燃油蒸气回收系统 fuel vapor recovery system液体回收装置 liquid withdrawal system恒量净化管 constant purge line碳罐净化管 canister purge line供油量 fuel delivery循环供油量 fuel delivery per cycle额定供油量 rated fuel delivery 怠速

48、供油量 idling speed fuel delivery 供油规律 fuel supply rate curve油量调节装置 fuel control unit供油提前角 fuel supply advance angle进油计量 inlet metering几何供油行程 geometric fuel delivery stroke供油率 fuel supply rate燃油通道 fuel gallery有效行程 effective stroke剩余行程 remainder stroke变行程计量 variable stroke metering等容卸载 constant volume u

49、nloading 变容卸载 variable volume unloading 收缩容积 retraction volume燃油喷油装置 fuel injection equipment燃油喷射泵 fuel injection pump滚轮式燃油喷射泵 roll fuel injection pump凸轮轴式燃油喷射泵 camshaft fuel injection pump直列式燃油喷射泵 in-line fuel injection pump伺服式燃油喷射泵 servo fuel injection pump底部突缘安装燃油喷射泵 base flanged mounted fuel inj

50、ection pump上部安装燃油喷射泵 high flanged-mounted fuel injection pump侧向安装燃油喷射泵 side-mounted fuel injection pump端部突缘安装式燃油喷射泵 end flange-mounted fuel injection pumpV形燃油喷射泵 vee fuel injection pump脉动式燃油喷射泵 jerk fuel injection pump 螺纹安装燃油喷射泵 screw-mounted fuel injection pump蓄能式燃油喷射泵 accumulator fuel injection pu

51、mp往复式燃油喷射泵 reciprocating fuel injection pump驱动轴式燃油喷射泵 driveshaft fuel injection pump单缸式燃油喷射泵 single cylinder fuel injection pump圆柱式燃油喷射泵 cylindrical fuel injection pump旋转式燃油喷射泵 rotary fuel injection pump分配式燃油喷射泵 distributor fuel injection pump多缸燃油喷射泵 multicylinder fuel injection pump框架安装式燃油喷射泵 cradl

52、e mounted injection pump喷油始点 fuel injection beginning喷油终点 fuel injection end喷油持续角 fuel injection duration angle喷油延迟 injection delay引燃喷射 pilot injection 启喷压力 injection starting pressure峰值喷油扭矩 peak injection torque峰值喷油压力 peak injection pressure喷油泵油缸数目 number of cylinders of an injection pump无气喷射 solid

53、 injection 喷射正时 injection timing集中喷射 group injection 喷油器 injector整体式喷油器 unit injector喷嘴 nozzle轴针式喷嘴 pintle type nozzle环槽式喷嘴 annular slot nozzle孔式喷嘴 hole type nozzle长杆喷嘴 long stem nozzle孔板式喷嘴 orifice plate nozzle开式喷嘴 open nozzle闭式喷嘴 closed nozzle喷油提前器 timing advance unit喷射泵壳体 injection pump housing针阀

54、 needle芯轴 central spindle喷嘴壳体 nozzle body针阀升程 needle lift喷嘴盖形螺母 nozzle cap nut喷油器壳体 nozzle holder突缘安装喷油器壳体 flanged-mounted injection nozzle holder燃油喷射泵传动装置 transmision of an injection pump喷嘴锥体 nozzle hole cone柱塞 plunger柱塞套 barrel柱塞行程 plunger stroke喷孔 spray orifice海拔控制器 altitude control提前器飞锤 flyweigh

55、t喷孔长径比 ratio of nozzle hole length nozzle diameter喷嘴液动力特性 nozzle hydrokinetic characteristics动态相位 dynamic phase喷孔面积 nozzle hole area喷嘴流通特性 nozzle flow characteristic喷油背压 injection back pressure高压油管 high pressure pipe平均喷油扭矩 mean injection torque喷油总效率 overall pumping efficiency峰值喷油压力 injection peak pressure预行程 prestroke收缩行程 retraction stroke燃油箱 fuel tank油箱盖 fuel tank油位表 fuel level gauge注油控制装置 fill control system汽油箱 gasoline tank( petrol tank)汽油供给管 gasoline feed pipe加油管 filler tube放油螺塞 drain plug吸油管 suction pipe刚性燃油管 rigid fuel pipe进油孔 fuel feed hole供油管 supply pi