发电机检测中英文对照
《发电机检测中英文对照》由会员分享,可在线阅读,更多相关《发电机检测中英文对照(4页珍藏版)》请在装配图网上搜索。
1、发电机的检测(中英文对照 )1. INSPECT GENERATOR BRUSH HOLDER ASSEMBLY检查发电机碳刷装置(a) Using vernier calipers,measure the exposed brush legth. 。用游标卡尺测出露在外面的碳刷的长度Standard exposed length:标准长度9.5 to 11.5 mm (0.374 to 0.453 in.)9.5 to 11.5 mm (0.374 to 0.453 in.)Minimum exposed length:最小长度1.5 mm ( 0.059 in.)1.5 mm ( 0.05
2、9 in.)If the exposed length is less than the minimum, neplace the generator brush holder assembly.如果碳刷长度小于最小值,替换发电机的碳刷装置。2. INSPECT GENERATOR REGULATOR ASSEMBLY检查发电机调节器装配(a) Using an ohmmeter, check the continuity between terminals F an B( a)使用欧姆表,检查F 与 B 之间的是否连通。Standard:标准 .When the positive and n
3、egative poles between terminals F and B are exchanged, there is continuity in one direction but no continuity in the other direction.当 F 和 B 之间的正极和负极被交换时,有在一个方向是连通的,但是在另一个方向的没有连通的。If the continuity is not as specified, replace the generator regulator assembly.如果不是规定的连通值,替换发电器调节器装配(b) Using an ohmmet
4、er, check the continuity between terminals F and E.( b)使用欧姆表,检查F 与 E 之间是否连通。Standard:标准:When the positive and negative poles between terminals F and E are exchanged, there is continuity in one direction but no continuity in the other direction.当 F 和 B 之间的正极和负极被交换时,有在一个方向是连通的,但是在另一个方向的没有连通的。If the co
5、ntinuity is not as specified, replace the generator regulator assembly.如果不是规定的连通值,替换发电器调节器装配3. INSPECT GENERATOR DRIVE END FRAME检查发动机定子线圈(a) Check the stator coil for open circuits.检查定子线圈的开路。(1)Using an ohmmeter, check the resistance between the coil leads.( 1)用欧姆表,检查电阻线圈之间的电阻。Standard resistance:标准
6、电阻:Below 1 低于 1If the result is not as specified, replace the generator assembly.如果不是规定电阻值,替换发电器定子线圈 装配(b)Inspect the stator for ground.检查定子线圈是否接地。(1) Using an ohmmeter, check the resistance between the coil lead and drive end frame.使用欧姆计,检查定子线圈与发动机壳体的电阻、Standard resistance:标准电阻:10 K or higher10K 或更
7、高If the result is not as specified, replace the generator assembly.如果不是规定电阻值,替换发电器定子线圈 装配(c) Inspect the bearing.( c)检查轴承。(1) Make sure that the bearing is not rough or worn.轴承是否粗糙或磨损过度。If necessary, replace the generator assembly.如果有必要, 替换发电器装配。4 INSPECT GENERATOR HOLDER WITH RECTIFIER 4 检查发电机整流器(a
8、) Using an ohmmeter, check the continuity among terminals P1, P2, P3 and B, andamong P1, P2, P3 and E.使用欧姆计,检查P1、 P2、 P3 和 B 之中和在P1、P2、 P3 和 E 之中是否连通Standard:标准When the positive and negative poles among terminals P1, P2, P3 and B are exchanged, there is continuity in one direction but no continuity
9、in the other direction.当 P1、P2、P3 和 B 之中的正极和负极交换时,有在一个方向是连通的,但是在另一个方向没有连通。When the positive and negative poles among terminals P1, P2, P3 and E are exchanged, there is continuity in one direction but no continuity in the other direction.当 P1、P2、P3 和 E 之中的正极和负极被交换时,有在一个方向的连通的,但是在另一个方向没有连通。If the cont
10、inuity is not as specified, replace the generator holder with rectifier.如果不是规定的连通值,将替换发电机整流器。5. INSPECT GENERATOR ROTOR ASSEMBLY5 。检查发电机转子装配(a) Check the generator rotor for open circuits.一)检查发电机转子开路。(1) Using an ohmmeter, measure the resistance between the slip rings.( 1 )用欧姆表,测量的滑环之间的电阻。Standard r
11、esistance: 1.7 to 2.1 at 20oC(68oF)标准电阻:在 20oC (68oF)的情况下1.7 到 2.1If the resistance is not as specified, replace the generator rotor assembly.如果不是规定电阻值,替换发电器转子 装配(b)Check the generator rotor for short circuits.(二)检查发电机转子的短路。(1) Using an ohmmeter, check the resistance between the slip ring and genera
12、tor rotor assembly.( 1)用欧姆表,检查滑环和发电机转子之间的电阻。Standard resistance:标准电阻:10K or higher10K 或更高If the result is not as specified, replace the generator rotor assembly.如果不是规定电阻值,替换发电器转子 装配(c)Inspect the slip rings.( c )检查的滑环。(1) Make sure that the slip rings are not rough or scored.( 1 )滑环不否粗糙或磨损过度。If roug
13、h or scored, replace the generator rotor assembly.如果 粗糙或磨损过度,替换发电器电动机滑环 装配(2) Using vernier calipers ,measure the slip ring diameter.( 2 )用卡尺,测量滑环的直径。Standard diameter:标准直径:14.2 to 14.4 mm (0.559 to 0.567 in. )14.2至 14.4毫米( 0.559至 0.567英寸Minimum diameter:最小直径:12.8mm (0.504 in .)12.8mm( 0.504英寸)If the diameter is less than the minimum, replace the generator rotor assembly.如果直径小于最小值,替换发电器电动机滑环 装配 。
- 温馨提示:
1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 装配图网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
最新文档
- 综合管廊智能控制方案ppt课件
- 世界知名放射性药物防护解决方案提供者TEMA-介绍课件
- 三年级下册《位置与方向》第一课时课件
- 阜新房地产市场调研报告
- 化学竞赛基础化学键与分子结构-课件
- 幼儿园班级管理分享ppt课件
- 组织变革的有效管理ppt课件
- 八年级数学下册第19章矩形菱形与正方形191矩形1矩形的性质课件新版华东师大版
- 八年级数学下册第19章矩形菱形与正方形191矩形1《矩形的性质》课件
- 八年级数学下册第1章12直角三角形课件新版北师大版
- 意识障碍分类及护理ppt课件
- 约分与通分的整理与复习ppt课件
- 八年级数学下册第19章矩形菱形与正方形192菱形1《菱形的性质》课件
- 八年级数学下册第19章四边形检测卷练习课件(新版)沪科版
- 世界经济概论ppt课件