8字盲板,插板及插环asme b16.48

《8字盲板,插板及插环asme b16.48》由会员分享，可在线阅读，更多相关《8字盲板,插板及插环asme b16.48（48页珍藏版）》请在装配图网上搜索。

1、真诚为您提供优质参考资料，若有不当之处，请指正。-,-,-,-,-Line Blanks42 / 48Date of Issuance: January 16, 2006The next edition of this Standard is scheduled for publication in 2010. There will be no addenda or written interpretations of the requirements of this Standard issued to this edition.ASME is the registered trademar

2、k of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American National Standards. The Standards Committee that approved the code or standard was balanced to ensure that individuals from competent and concerned i

3、nterests have had an opportunity to participate. The proposed code or standard was made available for public review and comment that provides an opportunity for additional public input from industry, academia, regulatory agencies, and the public-at-large.ASME does not “approve,” “rate,” or “endorse”

4、 any item, construction, proprietary device, or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document and does not undertake to insure anyone utilizing a standard against liability for infringement

5、of any applicable letters patent, nor assume any such liability. Users of a code or standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, is entirely their own responsibility.Participation by federal agency represent

6、ative(s) or person(s) affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the establishedASME procedures and policies, which precludes th

7、e issuance of interpretations by individuals.No part of this document may be reproduced in any form, in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue, New York, NY 10016-5990Copyright 20

8、06 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All rights reservedPrinted in U.S.A.-,-,-,-,-CONTENTSForeword .ivCommittee Roster .v1Scope .12Pressure-Temperature Ratings .13Design .24Dimensions .25Materials .36Marking .37Paddle Blank and Spacer Identification .38Testing .3Figure1 Line Blanks .2Ta

9、bles1Dimensions of Class 150 Raised Face Figure-8 Blanks .42Dimensions of Class 300 Raised Face Figure-8 Blanks .53Dimensions of Class 600 Raised Face Figure-8 Blanks .64Dimensions of Class 900 Raised Face Figure-8 Blanks .75Dimensions of Class 1500 Raised Face Figure-8 Blanks .86Dimensions of Class

10、 2500 Raised Face Figure-8 Blanks .97Dimensions of Class 150 Female Ring-Joint Facing Figure-8 Blanks .108Dimensions of Class 300 Female Ring-Joint Facing Figure-8 Blanks .119Dimensions of Class 600 Female Ring-Joint Facing Figure-8 Blanks .1210Dimensions of Class 900 Female Ring-Joint Facing Figure

11、-8 Blanks .1311Dimensions of Class 1500 Female Ring-Joint Facing Figure-8 Blanks .1412Dimensions of Class 2500 Female Ring-Joint Facing Figure-8 Blanks .1513Dimensions of Class 150 Male Oval Ring-Joint Facing Figure-8 Blanks .1614Dimensions of Class 300 Male Oval Ring-Joint Facing Figure-8 Blanks .1

12、715Dimensions of Class 600 Male Oval Ring-Joint Facing Figure-8 Blanks .1816Dimensions of Class 900 Male Oval Ring-Joint Facing Figure-8 Blanks .1917Dimensions of Class 1500 Male Oval Ring-Joint Facing Figure-8 Blanks .2018Dimensions of Class 2500 Male Oval Ring-Joint Facing Figure-8 Blanks .21Nonma

13、ndatory AppendicesADimensional Data for Line Blanks in U.S. Customary Units .22BReferences .41CQuality System Program .42iii-,-,-FOREWORDIn July 1993, the ASME B16 Committee gave to its Subcommittee C the assignment to convert the API 590 Steel Line Blanks Standard into an ASME standard. The America

14、n Petroleum Institute no longer publishes the API 590 Standard.These line blanks were designed in accordance with the rules of the ASME B31.3-2002 edition. Materials and relevant footnotes have been added following the ASME format.Significant additions made to this 2005 edition include reference to

15、the use of all materials listed in B16.5 Table 1-A plus Metric units. The added materials of construction include additions to classes of alloy steels, stainless steels, and nickel alloys. This edition has also been metricated over previous editions to include both U.S. Customary units (in parenthes

16、is) and Metric units in the text, Metric units in dimensional tables in the body, and U.S. Customary units in dimensional tables in Nonmandatory Annex A.All requests for interpretations or suggestions for revisions should be sent to the Secretary, B16 Committee, The American Society of Mechanical En

17、gineers, Three Park Avenue, New York, NY 10016-5990.The B16 Committee operates under procedures accredited by the American National Standards Institute (ANSI). Following approval by the Standards Committee and ASME, this revision to the 1997 edition was approved as an American National Standard by A

18、NSI on September 19,2005 with the designation ASME B16.48-2005.ivASME B16 COMMITTEE Standardization of Valves, Flanges, Fittings, and Gaskets(The following is the roster of the Committee at the time of approval of this Standard.)OFFICERSW. N. McLean, ChairR. A. Schmidt, Vice ChairC. Artibee, Secreta

19、ryR. W. Barnes, Anric Enterprises, Inc.COMMITTEE PERSONNELW. N. McLean, Newco ValvesW. B. Bedesem, ExxonMobil Research and Engineering Co.M. A. Clark, Nibco, Inc.C. E. Floren, Mueller Co.D. R. Frikken, Becht Engineering Co.G. G. Grills, U.S. Coast GuardA. Hamilton, ABS AmericasM. L. Henderson, Forgi

20、tal USA-,-,-G. A. Jolly, Vogt Valves/Flowserve M. Katcher, Haynes International R. Koester, Honorary MemberT. A. McMahon, Fisher Controls International, Inc.M. L. Nayyar, Bechtel Power Corp.J. D. Page, U.S. Regulatory CommissionP. A. Reddington, The American Society of Mechanical EngineersR. A. Schm

21、idt, Trinity-ladishH. R. Sonderegger, Anvil International, Inc.W. M. Stephan, Flexitallic LPT. F. Stroud, Ductile Iron Pipe Research AssociationR. E. White, Richard E. White & Associates PCD. A. Williams, Southern Company ServicesD. R. Frikken, Chair, Becht Engineering Co.C. Artibee, Secretary, The

22、American Society of MechanicalEngineersV. C. Bhasin, SigmatechG. D. Conlee, ConsultantW. C. Farrell, Jr., ConsultantM. L. Henderson, Coffer Corp.R. E. Johnson, Flowline DivisionSUBCOMMITTEE CR. Koester, Honorary MemberW. N. McLean, Newco ValvesM. L. Nayyar, Bechtel Power Corp.R. A. Schmidt, Trinity-

23、ladishD. L. Shira, Taylor ForgeJ. C. Thompson, Milwaukee ValveL. A. Willis, Dow Chemical Co.v-,-,-viASME B16.48-2005LINE BLANKS1SCOPE1.1 GeneralThis Standard covers pressure-temperature ratings, materials, dimensions, tolerances, marking, and testing for operating line blanks in sizes NPS 12 through

24、 NPS 24 for installation between ASME B16.5 flanges in the 150,300, 600, 900, 1500, and 2500 pressure classes.1.2 Definitions1.2.1 Figure-8 Blank. A figure-8 blank (also called a spectacle blank) is a pressure-retaining plate with one solid end and one open end connected with a web or tie bar (see F

25、ig. 1).1.2.2 Paddle Blank. A paddle blank is similar to the solid end of a figure-8 blank. It has a plain radial handle. It is generally used in conjunction with a paddle spacer in large sizes.1.2.3 Paddle Spacer. A paddle spacer is similar to the open end of a figure-8 blank. It has a plain radial

26、handle. It is generally used in conjunction with a paddle blank.1.3 ReferencesCodes, standards, and specifications, containing pro- visions to the ext ent ref eren ce d h erei n, co ns t i tu t e requirements of this Standard. These reference docu- ments are listed in Nonmandatory Appendix B.1.4 Qua

27、lity SystemsNonmandatory requirements relating to the product manufacturer s Quality System Program are described in Nonmandatory Appendix C.1.5 Relevant Units-,-,-This St andard st at es val ue s i n b ot h M et ri c a nd U.S. Customary units. These systems of units are to be regarded separately as

28、 standard. Within the text, the U.S. Customary units are shown in parenthesis or sepa- rate tables. Refer to Nonmandatory Appendix A. The values stated in each system are not exact equivalents; therefore, it is required that each system of units be used independently of the other. Combining values f

29、rom the two systems constitutes nonconformance with the Stan- dard. Nonmandatory Appendix A provides dimensions in U.S. Customary units.1.6 ConventionFor the purpose of determining conformance with this Standard, the convention for fixing significant digitswhere limits and maximum and minimum values

30、 are specified, shall be rounded as defined in ASTM Practice E 29. This requires that an observed or calcu- lated value shall be rounded off to the nearest unit in the last right-hand digit used for expressing the limit. Decimal values and tolerances do not imply a particular method of measurement.1

31、.7 SizeNPS, followed by a dimensionless number, is the des- ignation for nominal blank size. NPS is related to the reference nominal diameter, DN, as defined in ISO 6708. The relationship is typically as follows:NPSDN12 1534 201251143211240250212653804100NOTE: For NPS 4, the related DN is DN p 25 (N

32、PS).1.8 Service ConditionsCriteria for selection of materials suitable for particu- lar fluid service are not wihtin the scope of this Standard.2 PRESSURE-TEMPERATURE RATINGS2.1 Pressure ClassesLine blanks covered by this Standard are for the fol- lowing pressure classes: 150, 300, 600, 900, 1500, a

33、nd2500 as listed in ASME B16.5.2.2 Pressure-Temperature Ratings2.2.1 Ratings. Ratings are the maximum allowable working gage pressure at the temperature shown in Tables 2 and F-2 of ASME B16.5 for the appropriate material and pressure class. For intermediate tempera- tures, linear interpolation betw

34、een temperatures within a pressure class is permitted by ASME B16.5.2.2.2 System Pressure Testing. Line blanks may be subjected to system tests at a pressure not to exceed1.5 times the 38C (100F) rating rounded off to the next higher 1 bar (25 psi) increment. Testing at any higher pressure is the re

35、sponsibility of the user, taking into1ASME B16.48-2005LINE BLANKSFigure-8 Blank Paddle Blank Paddle SpacerFig. 1 Line Blanksaccount the requirements of the applicable code or regulation.2.2.3 Mixed Material Joints. Should either the two flanges or the line blank in a flanged line blank assembly not

36、have the same pressure-temperature rating, the rat- ing of the assembled joint at any temperature shall be the lower of the flange or line blank rating at that temper- ature.3DESIGN3.1 HandleThe handle or web (tie bar) may be integral or attached to the line blank or spacer. The web and its attachme

37、nt shall be capable of supporting the weight of the blank or spacer in all orientations without permanent defor- mation to the web.3.2 Edge PreparationFinished surfaces shall be free of project ions that would interfere with gasket seating.3.3 Facing3.3.1 Raised Face Joint Blanks. The gasket seating

38、 surface finish and dimensions for raised face line blanks shall be in accordance with ASME B16.5. A raised face may be specified at the option of the purchaser. The height of the raised faces shall be in addition to thethicknesses, t, listed in Tables 1 through 6 (Tables A-1 through A-6 in Nonmanda

39、tory Appendix A).3.3.2 Female Ring-Joint Blanks. Female ring-joint grooves shall be shaped with the groove side wall sur- face finish not exceeding 1.6 m (63 in.) Ra roughness. The finish of the gasket contact faces shall be judged by visual comparison with Ra standards (see ASME B46.1) and not by i

40、nstruments having stylus tracers and elec- tronic amplification.3.3.3 Male Ring-Joint Blanks. The gasket shape (ring) for male ring-joint blanks shall not exceed 1.6 m (63 in.) Ra roughness. The finish of the gasket contact faces shall be judged by visual comparison with Ra stan- dards (see ASME B46

41、.1) and not by instruments having stylus tracers and electronic amplification.4DIMENSIONS4.1 GeneralDimensions shall be in accordance with Tables 1 through 18 (Tables A-1 through A-18 of Nonmandatory Appendix A).4.2 Tolerances4.2.1 Facing Tolerances. Tolerances for facings shall be in accordance wit

42、h ASME B16.5.4.2.2 Thickness Tolerances. Thickness tolerances areNPS 18 and smaller zero + 3.0 mm (0.12 in.)NPS 20 and larger zero + 4.8 mm (0.19 in.)4.3 Openings(a) For NPS 12, NPS 34, and NPS 1 blanks in all raised face classes, the inside diameter is equal to standard weight welding neck flange b

43、ore.(b) For NPS 114 and larger blanks in Classes 150 and300 raised face, the inside diameter is equal to the pipeoutside diameter.(c) For NPS 114 and larger blanks in Classes 600 and900 raised face, the inside diamet er is equal to Schedule 10S welding neck flange bore.(d) For Class 1500 raised face

44、 blanks, the inside diam- eter is equal to Schedule 40 welding neck flange bore. (e) For Class 2500 raised face blanks, the inside diame-ter is equal to Schedule 40 through NPS 6, Schedule 60for NPS 8 and NPS 10, and Schedule 80 for NPS 12.(f ) For all ring-joint blanks, the inside diameter is equal

45、 to the pipe outside diameter.(g) Dimensions are based upon concentric installation of spiral wound gaskets with inner rings as required by ASME B16.20 and conform to the maximum permitted bore of ASME B16.5 welding neck flanges described in Table 16 of ASME B16.20.-,-,-2LINE BLANKSASME B16.48-20054

46、.4 Facing FinishFacing finish shall be in accordance with ASME B16.5, para. 6.4.5.5MATERIALSMaterials for line blanks shall be in accordance with ASME B16.5, Table 1-A, and shall include mat erial restrict ions cit ed in not es to Tables 2 o r F-2 of A S ME B 16 .5 . R ec om me nd ed bo lt in g m at

47、 er ia ls for flange-blank assemblies are list ed in ASME B16.5, Table 1-B.Criteria for the selection of materials are not within the scope of this Standard.6MARKING6.1 General(a) Line blanks shall be marked as follows:(1) Manufacturer s name or trademark(2) Material, specification, and grade or cla

48、ss(3) Pressure class(4) B16(5) Size (NPS)(6) Ring number (if applicable)(b) Where space does not permit all of the above markings, they may be omitted in the reverse order given in 6.1(a).(c) The B16 designation may be applied only when the line blank has been manufactured in full confor- mance with

49、 this Standard.6.2 Marking MethodThe marking shall be applied by steel stamping on the web (tie bar) or handle. Where space is limited, marking may be stamped on the outside edge of the blind portion of blanks.7PADDLE BLANK AND SPACER IDENTIFICATION7.1 Paddle HandlesIn order to differentiate between

50、 an installed paddle spacer and a paddle blank, it is required that there be an externally visible distinction between the two as required by paras. 7.2 and 7.3.7.2 Paddle Blank HandlesHandles for paddle blanks shall be solid with no openings.7.3 Paddle Spacer HandlesHandles for paddle spacers shall

51、 have a single through indicator hole located near the end of the handle. The hole diameter shall not be less than 12 mm (12 in.).8TESTINGLine blanks are not required to be pressure tested.3-,-,-ASME B16.48-2005LINE BLANKSNote (1)OWAOBNote (3)ttWNote (3)-,-,-Note (2)Table 1Dimensions of Class 150 Ra

52、ised Face Figure-8 BlanksInside Diameter, B, mmOutside Diameter, O, mmCenterline Dimension, A, mmThickness, t, mmWeb Width, W, mm1645603.0382154703.0382764803.0384273906.43848831006.438611021206.451731071406.451891331506.4641021591759.7641141721909.7641411942159.77616821924012.77621927630012.7762733

53、3736015.710232440643019.110235644847519.110840651146022.410845754658025.411450860363528.412161071475031.8140NPS1234111411222123312456810121416182024GENERAL NOTE: Dimensions are in millimeters. For inch dimensions, refer to corresponding Table A-1 inNonmandatory Appendix A. NOTES:(1) Hole size (where

54、 required due to bolt spacing) shall be the same as the flange bolt hole and locatedsuch that it will not interfere with bolting between two flanges.(2) The thickness of the web (or tie bar) dimension, Wt, shall be as determined by para. 3.1. (3) Refer to para. 3.3.1.4LINE BLANKSASME B16.48-2005Note (1)OWAOBNote (3)ttWNote (3)Note (2)Table 2Dimensions of Class 300 Raised Face Figure-8 BlanksInside Diameter, B, mmOutside Diameter, O, mmCenterline Dimension, A, mmThickness, t, mmWeb Width, W, mm1651656.4382164806.4382770906.43842791006.43848921156.