模具术语翻译

《模具术语翻译》由会员分享，可在线阅读，更多相关《模具术语翻译（33页珍藏版）》请在装配图网上搜索。

1、模具名词中英文对照表序号 中文名 英文名1 一、水口gate2 进水位gate location3 水口形式gate type4 大水口edge gate5 细水口 pin-point gate6 水口大小gate size7 转水口switching gate8 唧嘴口径sprue diameter9 二、流道runner10 热流道hot runner11 冷流道cold runner12 唧嘴直流direct sprue gate13 圆形流道round runner14 模流分析mold flow analysis15 流道平衡runner balance16 热嘴hot sprue1

2、7 热流道板hot manifold18 发热管cartridge heater19 探针thermocouples20 插头connector plug21 插座 connector socket22 密封/封料 seal23 三、运水water line24 喉塞line pug25 喉管tube26 塑胶管plastic tube27 快速接头jiffy quick connector plug28 四、模具零件mold components29 三板模three-plate mold模具名词中英文对照表序号 中文名 英文名30 二板模two-plate mold31 边钉/导边lead

3、er pin/guide pin32 边司/导套bushing/guide bushing33 顶针板ejector retainer plate34 托板support plate35 螺丝 screw36 管钉dowel pin37 开模槽ply bar score38 内模管位core/cavity inter-lock39 顶针ejector pin40 司筒ejector sleeve41 司筒针ejector pin42 推板stripper plate43 缩呵movable core44 扣机（尼龙拉勾） nylon latch lock45 斜顶lifter46 模胚（架）

4、mold base47 母模cavity insert48 公模core insert49 行位（滑块） slide50 镶件insert51 压座/斜鸡wedge52 耐磨板/油板wedge wear plate53 压条plate54 撑头support pillar55 唧嘴 sprue bushing56 挡板stop plate57 定位圈locating ring58 锁扣latch模具名词中英文对照表序号 中文名 英文名59 扣鸡parting lock set60 推杆push bar61 栓打螺丝S.H.S.B62 顶板ejector plate63 活动臂lever arm

5、64 水口司bush65 垃圾钉stop pin66 隔片buffle67 弹弓柱spring rod68 弹弓die spring69 镶针pin70 销子dowel pin71 波子弹弓ball catch72 喉塞pipe plug73 锁模块lock plate74 斜顶angle from pin75 斜顶杆angle ejector rod76 尼龙拉勾parting locks77 复位键、提前回杆early return bar78 气阀valves79 斜导边angle pin80 模排气parting line venting81 模总高超出啤机规格mold base sh

6、ut height82 模胚原身出料位cavity direct cut on A-plate，coredirect cut on B-plate.83 不准用镶件Do not use (core/cavity) insert84 用铍铜做镶件use beryllium copper insert85 强度不够insufficient rigidity86 公差tolerance87 铜公(电极) copper electrode动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate动模座板

7、 Moving Clamp Plate Bottom Clamping Plate Bottom Plate上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavity-retainer Plate型芯固定板 Mould Core-retainer Plate凸模固定板 Punch-retainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base L

8、eg模头 Die Head 根据国家标准，以下为部分压铸模具术语的标准翻译。 压力铸造模具 Die-Casting Die压铸模零部件定模 Fixed Die Cover Die定模座板 Fixed Clamping Plate定模套板 Bolster Fixed Die动模 Moving Die Ejector Die动模座板 Moving Clamping Plate直流道 Sprue横流道 Runner内浇口 Gate 模具分类 Injection Mold 注塑模Plastic Rubber Mould 塑胶模Rubber Molding 橡胶成形Hot Chamber Die Cas

9、ting 热室压铸Sand Mold Casting 砂模铸造Extrusion Mold 挤出模Multi-Cavity Mold 多模穴模具Stack Mold, Stack Injection Mould 叠层模Plaster Mold 石膏模Three Plates Mold 三板模Plain Die 简易模Pierce Die 冲孔模Forming Die 成型模Progressive Die 连续模Gang Dies 复合模Shearing Die 剪边模Cavity Die 型腔模Riveting Die 铆合模Compression Molding 压缩成型Flash Mold

10、 溢流式模具Extrusion Mold 挤压式模具Split Mold 分割式模具Mould Cavity 型腔 母模Mold Core 模芯 公模Large Die Mold 大型模具Precise Die Mold 精密模具Complex Die Mold 复杂模具Foaming Mould 发泡模具Metal Die 金属模具Plastic Mold 塑料模具Press Tool Stamping Die Punch Die 冲压模具Extrusion Die 挤压模具Graphite Die 石墨模具 流道浇口部分 Runner System 浇道系统Sprue Cold Mater

11、ial Trap 浇道 冷料井Sprue Puller 拉杆Runner Design 流道设计Main Runner 主流道Secondary Runner 次流道Mould Gate Design 浇口设计Submarine Gate 潜伏浇口Tunnel Gate 隧道式浇口Pinpoint Gate 点浇口Fan Gate 扇形浇口Side Gate 侧浇口Edge Gate 侧缘浇口Tab Gate 搭接浇口Film Gate 薄膜浇口Flash Gate 闸门浇口Slit Gate 缝隙浇口Dish Gate 盘形浇口Diaphragm Gate 隔膜浇口Ring Gate 环形浇

12、口Runnerless 无浇道Sprueless 无射料管方式Long Nozzle 延长喷嘴方式Sprue 浇口，溶渣Insulated Runner Hot Runner 热浇道Runner Plat 浇道模块Valve Gate阀门浇口Slag Well 冷料井Cold Slag 冷料渣Sprue Gate 射料浇口，直浇口Nozzle 射嘴Sprue Lock Pin 料头钩销（拉料杆） 注塑缺陷 Flash 飞边Warpage 翘曲Air Trap 积风Blush 发赤Flow Line 流痕Splay 银纹Short Shot 短射Sink Mark 缩痕Streak 条纹Void

13、 缩孔Weld Line 熔接线Gas Mark 烧焦Cold Slug 冷斑Delamination 起皮Burr 毛刺Flaw Scratch 刮伤Gloss 光泽Glazing 光滑Surface Check 表面裂痕Hesitation 迟滞 注塑工艺 Molding Conditions 成型条件Drying 烘干Barrel Temperature 料筒温度Melt Temperature 熔化温度Mold Temperature 模具温度Injection Pressure 注塑压力Back Pressure 背压Injection Speed 注塑速度Screw Speed 螺

14、杆转速Tensile Strength 抗拉强度Tensile Elongation 延伸率Flexural Modulus 弯曲模数Flexural Strength 抗弯强度Shrinkage 收缩率Regrind Usage 次料使用Moulding 模塑 机械设备 Lathe 车床Planer 刨床Miller Milling Machine 铣床Grinder 磨床Driller 钻床Linear Cutting 线切割Electrical Sparkle 电火花Welder 电焊机Punching Machine 冲床Robot 机械手Common Equipment 常用设备ED

15、M Electron Discharge Machining 放电加工3D Coordinate Measurement 三次元量床Boring Machine 搪孔机Contouring Machine 轮廓锯床Copy Grinding Machine 仿形磨床Cylindrical Grinding Machine 外圆磨床Die Spotting Machine 合模机Engraving Machine 雕刻机Engraving E.D.M 雕模放置加工机Form Grinding Machine 成形磨床, Graphite Machine 石墨加工机Horizontal Borin

16、g Machine 卧式搪孔机Horizontal Machine Center 卧式加工制造中心Internal Cylindrical Machine 内圆磨床 模具零件 Top Plate 上托板（顶板）Top Block 上垫脚Punch Set 上模座Punch Pad 上垫板Punch Holder 上夹板Stripper Pad 脱料背板Up Stripper 上脱料板Male Die 公模（凸模）Feature Die 公母模Female Die 母模（凹模）Upper Mold Plate 上模板Lower Mold Plate 下模板Die Pad 下垫板Die Holde

17、r 下夹板Die Set 下模座Bottom Block 下垫脚Bottom Plate下托板（底板）Stripping Plate 内外打（脱料板）Outer Stripper 外脱料板Inner Stripper 内脱料板Lower Stripper 下脱料板Inner Guiding Post 内导柱Inner Hexagon Screw 内六角螺钉Dowel Pin 固定销Mould Coil Spring 模具弹簧Lifter Pin 顶料销Isoheight Sleeve 等高套筒Pin 销Lifter Guide Pin 浮升导料销Guide Pin 导正销Wire Spring

18、 圆线弹簧Outer Guiding Post 外导柱Stop Screw 止付螺丝Located Pin 定位销Outer Bush 外导套Punch 冲头Insert 入块（嵌入件）Deburring Punch 压毛边冲子Groove Punch 压线冲子Stamped Punch 字模冲子Round Punch 圆冲子Special Shape Punch 异形冲子Bending Block 折刀Roller 滚轴Baffle Plate 挡块Located Block 定位块Supporting Block for Location 定位支承块Air Cushion Plate 气垫

19、板Air-Cushion Eject-rod 气垫顶杆Trimming Punch 切边冲子Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子Reel-stretch Punch 卷圆压平冲子Guide Plate 定位板Sliding Block 滑块Sliding Dowel Block 滑块固定块Active Plate 活动板Lower Sliding Plate 下滑块板Upper Holder Block 上压块Upper Mid Plate 上中间板Spring Box 弹簧箱Spring-Box Eject-rod 弹簧箱顶杆

20、Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板Guide Pad 导料块 模具技术用语 各种常用模具成形方式Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压

21、出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forgi

22、ng 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow Blow Molding 中空（吹出）成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造L

23、ost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Close Mold 合模Demould 脱模 脱模剂Mould Unloading 开模Eject 顶出Tool Change Retooling Die Changing 换模Mould Clamping 锁模 各式模具分类用语 Bismuth Mold 铋铸模Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套

24、式模具Center-Gated Mold 中心浇口式模具Loose Detail Mold 活零件模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模法Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模

25、Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive

26、Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具 原型模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模 切缝模Raising（Embossing） 压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具Shaper 定型模

27、套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具Unscrewing Mold 退扣式模具Yoke Type Die 轭型模 模具厂常用之标准零配件

28、 Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流档板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Castin

29、g lug 铸耳Cavity 模穴（模仁）Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clampe

30、r 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫

31、Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯 椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate

32、Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Insert 嵌件Insert Pin 嵌件梢King Pin 转向梢King

33、 Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针 起模杆Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold B

34、ase 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头 锤击强化冲头 钻杆凸模Pilot Pin 定位销 导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Push

35、er Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton 骨架Slag Ris

36、er 冒渣口Slide（Slide Core） 滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道拉料 浇道推出杆 注道残料顶销Spew Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Limit Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动

37、环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱 顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢 锥形梢Teeming Pouring 浇注Three Start Screw 三条螺纹Thrust Pin 推

38、力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板 模具常用之工作机械 3D Coordinate Measurement 三次元量床Boring Machine 搪孔机CNC Milling Machine CNC铣床Contouring Machine 轮廓锯床Copy Grinding Machine 仿形磨床Copy Lathe 仿形车床Copy Milling Machine 仿形铣床Copy Shaping Machine 仿形刨床Cylindrical Grinding Machine 外圆磨床Die Spotting M

39、achine 合模机Drilling Machine 钻孔机Engraving Machine 雕刻机Engraving E.D.M 雕模放置加工机Form Grinding Machine 成形磨床Graphite Machine 石墨加工机Horizontal Boring Machine 卧式搪孔机Horizontal Machine Center 卧式加工制造中心Internal Cylindrical Machine 内圆磨床Jig Boring Machine 冶具搪孔机Jig Grinding Machine 冶具磨床Lap Machine 研磨机Machine Center 加

40、工制造中心Multi Model Miller 靠磨铣床NC Drilling Machine NC钻床NC Grinding Machine NC磨床NC Lathe NC车床NC Programming System NC程式制作系统Planer 龙门刨床Profile Grinding Machine 投影磨床Projection Grinder 投影磨床Radial Drilling Machine 旋臂钻床Shaper 牛头刨床Surface Grinder 平面磨床Try Machine 试模机Turret Lathe 转塔车床Universal Tool Grinding Mac

41、hine 万能工具磨床Vertical Machine Center 立式加工制造中心Wire E.D.M 线割放电加工机 入水 Gate 进入位 Gate Location水口形式 Gate Type大水口 Edge Gate细水口 Pin-point Gate水口大小 Gate Size转水口 Switching Runner Gate唧嘴口径 Sprue Diameter流道 Mold Runner热流道 Hot Runner Hot Manifold温度控制器 温控器 Thermostat Thermoregulators Temperature Controller热嘴冷流道 Hot

42、 Sprue Cold Runner唧嘴直流 Direct Sprue Gate圆形流道 Round Full Half Runner流道电脑分析 Mold Flow Analysis流道平衡 Runner Balance热嘴 Hot Sprue热流道板 Hot Manifold发热管 Cartridge Heater探针 Thermocouples插头 Connector Plug插座 Connector Socket密封 封料 Seal 运水 Water Line 喉塞 Line Plug Throat Taps喉管 Tube塑胶管 Plastic Tube快速接头 Jiffy Quick

43、 Connector Quick Disconnect Coupling 模具零件 Mold Components 三板模 3-Plate Mold二板模 2-Plate Mold边钉 导边 Leader Pin Guide Pin边司 导套 Bushing Guide Bushing中托司 Shoulder Guide Bushing中托边 Guide Pin顶针板 Ejector Retainner Plate托板 Support Plate螺丝 Screw管钉 Dowel Pin开模槽 Ply Bar Scot内模管位 Core Cavity inter-Lock顶针 Ejector P

44、in司筒 Ejector Sleeve司筒针 Ejector Pin推板 Eject Plate Push Plate Stripper Plate缩呵 Movable Core Return Core Puller扣机（尼龙拉勾） Nylon Latch Lock斜顶 Lifter模胚（架） Mold Base上内模 Cavity Insert下内模 Core Insert行位（滑块） Slide镶件 Insert压座 Wedge耐磨板 油板 Wedge Wear Plate压条 Plate撑头 Support Pillar唧嘴 Sprue Bushing挡板 Stop Plate定位圈 L

45、ocating Ring锁扣 Latch扣机 Parting Lock Set推杆 Push Bar栓打螺丝 S.H.S.B顶板 Ejector Plate活动臂 Lever Arm分流锥 Sprue Spreader分流板 Spreader Plate水口司 Bush垃圾钉 Stop Pin隔片 Buffle弹弓柱 Spring Rod弹弓 Die Spring中托司 Ejector Guide Bush中托边 Ejector Guide Pin镶针 Pin销子 Dowel Pin波子弹弓 Ball catch喉塞 Pipe Plug锁模块 Lock Plate斜顶 Angle from P

46、in斜顶杆 Angle Ejector Rod尼龙拉勾 Parting Locks活动臂 Lever Arm复位键 提前回杆 Early Return Bar气阀 Valves斜导边 Angle Pin术语 Terms承压平面平衡 Parting Surface Support Balance模排气 Parting Line Venting回针碰料位 Return Pin and Cavity Interference顶针碰运水 Water Line Interferes with Ejector Pin料位出上 下模 Part from Cavith （Core） Side不准用镶件 Do

47、Not Use （Core Cavity） Insert用铍铜做镶件 Use Beryllium Copper Insert初步模图设计 Preliminary Mold Design正式模图设计 Final Mold Design弹弓压缩量 Spring Compressed length稳定性好 Good Stability Stable强度不够 Insufficient Rigidity均匀冷却 Even Cooling扣模 Sticking热膨胀 Thermal Expansion公差 Tolerance铜公（电极） Copper ElectrodeAir Vent Valve 通气阀

48、Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流挡板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom Board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting Lug 铸耳Cavity 模腔 模

49、穴（模仁）Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器

50、Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Eject

51、or Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯 椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land

52、浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Joint Pipe Coupler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Inserts 嵌件Insert Pin 嵌件梢King Pin

53、转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mol

54、d Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头 钻杆凸模Pilot Pin 定位销 导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher P

55、in 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton Frameworks 骨架S

56、lag Riser 冒渣口Slide（Slide Core） 滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道残料顶销 浇道推出杆Sprue Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环St

57、opper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱 顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢 锥形梢Teeming 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉

58、杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板Pierce 冲孔Forming 成型（抽凸 冲凸）Draw Hole 抽孔Bending 折弯Trim 切边Emboss 凸点Dome 凸圆Semi-Shearing 半剪Stamp Mark 冲记号Deburr or Coin 压毛边Punch Riveting 冲压铆合Side Stretch 侧冲压平Reel Stretch 卷圆压平Groove 压线Blanking 下料Stamp Letter 冲字（料号）Shearing 剪断Tick-Mark Nearside 正面压印Tick-Mark Fa

59、rside 反面压印Extension Drawing 展开图procedure Drawing 工程图Die Structure Drawing 模具结构图Material 材质Material Thickness 料片厚度Factor 系数Upward 向上Downward 向下Press Specification 冲床规格Die Height Range 适用模高Die Height 闭模高度Burr 毛边Gap 间隙Weight 重量Total Weight 总重量Punch Weight 上模重量Compression Molding 压缩成型Flash Mold 溢流式模具Extrusion Mold 挤压式模具Split Mold 分割式模具Cavity 型腔 母模Mold Core 模芯 公模Taper 锥拔Leather Cloak 仿皮革Shiver 饰纹Flow Mark 流痕Welding Mark 溶合痕Post Screw Insert 螺纹套