直流专用继电器-元则电器推荐(共6页)

《直流专用继电器-元则电器推荐(共6页)》由会员分享，可在线阅读，更多相关《直流专用继电器-元则电器推荐(共6页)（6页珍藏版）》请在装配图网上搜索。

1、精选优质文档-倾情为你奉上 直 流 专 用 继 电 器 产 品 承 认 书SPECIFICATION FOR APPROVAL 客户名称Customer name： 产品名称Product Description： 直流专用继电器 Relay 供方型号Supplier Part No.： YAE-112D 客户料号Customer Material Code： 客户型号Customer Part No.： 版 本REV： 日 期Date： 供应厂商制定审核批准客户确认开发/工程 审核品质部 审核批准 一、基本特性Basic characteristics1、 直流专用线圈参数Coil spec

2、ification(1) 额定电压Nominal voltageDC 12V(2) 线圈阻抗Coil resistance8510% (at 235)(3) 额定电流Rated currentDC 140mA10% (at 235)(4) 动作电压Operate voltageDC 9.0V Max (at 235)(5) 释放电压Release voltageDC 0.6V Min (at 235)(6) 最大电压Maximum voltageDC 15.6V(130% of nominal voltage)(7) 线圈温升Coil temperature rise50K Max (Coil

3、:12V)2、 触点参数Contact Specification(1) 触点型式Contact configurationSPDT (1 Form C)-单刀双掷（一组转换型触点）(2) 触点额定负载Contact rating40A 14VDC(3) 接触电阻Contact resistanceInitial（初始值） 100 m Max (At DC6V 1A)(4) 动作时间Operate time20ms Max(5) 释放时间Release time20ms Max(6) 最大动作频率Maximum operatingMechanically 18000 cycle/h（机械）fr

4、equency Electrically 600 cycle/h（电气）(7) 触点温升Contact temperature rise50K Max (Contact: 40A)3、 直流专用继电器通用参数General Specification(1) 绝缘阻抗Insulation resistance100M Min (at DC500V)(2) 电气强度Dielectric strength触点间between open contacts500VAC,50/60 HZ for 1Minute线圈与触点间between contacts and coil500VAC,50/60 HZ f

5、or 1 Minute(3) 环境温度Ambient temperature-40+85(Not freezing and condensing at low temperature)(4) 相对湿度Relative Humidity45% to 85% RH(5) 电气寿命Electrical life100,000 Operations Min (at 40A 14VDC)(6) 机械寿命Mechanical life10,000,000 operations Min4、 体系、安规认证和环保Quality System、Safety Certification and RoHS(REAC

6、H)(1) UL certified(2) TUV certified(3) CQC certified(4) ISO9001:2008 certifiedFile No. 05311Q22581R0S(5) RoHS and REACH Compliant二、环境参数Environmental Characteristics1、 抗振动性Vibration resistance1.1 误动作Error operation在X、Y、Z轴三个方向施加双振幅为1.5mm，频率为10-55HZ的振动，时间5分钟，误动作时间不超过1ms。At constant vibration of double

7、amplitude 1.5mm, 1055 HZ , in each direction of X,Y,Z for 5 minutes. No error operation more than 1 ms. 1.2 耐久性Endurance在三个方向施加振动2小时，无结构损坏。No construction trouble when vibrate it from 3 directions for 2 hours.( Amplitude 1.5mm, 1055 HZ)2、 抗冲击性Shock resistance2.1 误动作Error operation在三个方向施加三次加速度为100m/s

8、2 持续时间11ms，误动作不超过1ms。At peak acceleration 100m/s2， duration 11ms, 3 shocks is given in each direction of X, Y, Z. No error operation more than 1 ms.2.2 耐久性Endurance三个方向三次加速度为1000m/s2 持续时间6ms，无结构损坏。No construction trouble when shock it from 3 directions 3 times at peak acceleration 1000m/s2， duration

9、 6ms.3、 耐寒性Cold resistance3.1 耐寒性Cold resistance放置于402环境温度下240小时，然后在标准条件下放置2小时，结构和性能无异常。No any trouble on construction or characteristic when leave relay in 402 for 240h. After that, leave it in standard condition for 2 hours.4、 耐热性Heat resistance4.1 耐热性Heat resistance放置于+852环境温度下240小时，然后在标准条件下放置2小时

10、，结构和性能无异常。No any trouble on construction or characteristic when leave relay in +852 for 240h. After that, leave it in standard condition for 2 hours。5、 耐湿性Moisture resistance5.1放置于40, 湿度90%环境下240小时，然后在标准条件下放置2小时，绝缘电阻最小10M，结构和性能无异常。After keeping relay for 240h in 40, 90%, then leave it in standard co

11、ndition for 2 hours。Insulation resistance 10M Min. No any trouble on construction or characteristic.三、端子性能Terminal characteristics1、端子强度Terminal strength在端子上施加10N压力10秒钟，无变形现象。10N pushed into any terminals for 10 s. There shall be no abnormalities.(The curving of the terminals shall be acceptable)2、端

12、子可焊性Terminal solderability 端子浸入2605焊锡槽中，时间50.5 s ，90%部位应该上锡。In case of lead free solder 2605, 50.5 s , 90% of the dipped portion shall be soldered.3、耐焊接热Soldering thermal端子浸入2605焊锡槽中，时间101 s，结构和性能无异常。 No any trouble on construction or characteristic. When dipped into solder bath 2605, 101s.四、标准测试条件S

13、tandardard test condition1、环境温度Ambient temperature2352、相对湿度Relative humidity 25%75%3、气压Air pressure86kPa106kPa4、测试位置Direction of Test 端子朝下位置Terminals down position五、储存条件Storage condition1、环境温度Ambient temperature-40+852、相对湿度Relative humidity 35%85%3、环境Environment3.1、不要储存在诸如硫化氢和盐雾气体等有腐蚀性的环境中。Store in

14、locations where the product or container is not expose to corrosive gas such as hydrogen sulfide or salty air.3.2、储存在没有可视尘埃的环境中。Store in locations where no visible dust exists.3.3、储存在没有直射阳光的环境中。Store in locations not subject to direct sunlight.六、外型图、线路板孔位图和线路图Outline、PCB Layout and Wiring diagram(un

15、it:mm) 外型图 安装尺寸（底视图） 接线图（底视图） 七、包装信息Packing InformationP/NInner packingCarton DimensionsQTY（PCS）/cartonNet weight（Kg）Gross weight（Kg） LWH（cm）YAE50pcs/box 49.0 x 35.8 x 22.5 50013.514.5八、命名规则Encoding InformationYAE X X X X X X1 2 3 4 5 6 7 1. 产品型号Product type: YAE2. 触点组数Contact Pole11 pole3. 线圈额定电压Co

16、il Nominal Voltage055VDC 1212VDC 2424VDC4. 线圈额定功率Coil Nominal PowerDStandard coil power标准功率5. 触点型式Contact arrangementBlank1 Form C M1 Form A B1 Form B6. 外壳型式Case type BlankCase without flange。不带法兰外壳 FCase with flange。带法兰外壳7. 特殊代码Special code(not necessary to be shown on product) Numbers or letters,

17、do not represent electrical changes, these codes denote customers requirements.九、特别提醒Reminds1、如有任何特殊要求，请联系元则电器公司。Any special requirements, please contact us.2、在诸如H2S、SO2或NO2有害气体的环境中，推荐选用完全密封型产品。Under the Environment with dangerous gas such as H2S, SO2 or NO2, fully sealed type is recommended.3、如果环境允许，优先选用防焊剂型产品。If the ambience allows, flux proof type is preferentially recommended.4、如果客户需要用超声波设备清洗PCB和继电器，则必须选用完全密封型产品。If the user washes the PCB and relay in the ultrasonic cleaner, fully sealed type must be selected.直流专用继电器;直流专用继电器价格;直流专用继电器继电器厂家;直流专用继电器继电器批发专心-专注-专业