Dewesoft机械故障诊断

《Dewesoft机械故障诊断》由会员分享，可在线阅读，更多相关《Dewesoft机械故障诊断（31页珍藏版）》请在装配图网上搜索。

1、Nr. 1Dewesoft机械故障诊断机械故障诊断Dewesoft 中国有限公司（北京）北京市通州区云景东路1号时尚街区园景国际大厦A座1508室Nr. 2旋转振动分析扭振测试阶次分析轨迹分析动平衡Machinery DiagnosticsNr. 3Rotational VibrationCustomer asks? can you measure the rpm deviation of my electromotor because I have to check my frequency converter? Is it possible that I measure the rpm d

2、eviation of my combustion engine? I would like to observe the rpm and rpm deviation of my paper mill. Can you measure the rpm and the rpm-deviation of the transmission system and the wheels together with other time based signals, like temperature, acceleration,CAN Bus. if we could measure the rpm de

3、viation of the helicopter rotor plates?Yes!Nr. 4What can we do?We can measure the rpm and the deviation of the rpm angle based and time based at the same time.Rotational Vibration Sometimes it looks like normal vibration, but at a closer look we see Rotational Vibration.Nr. 5Rotational VibrationWhat

4、 do we need?Pickup, Encoder,or RIE-360-RPM sensor SensorCounter InputNr. 6 prepared Analyse function Counter Input Rotational Vibration How to set it up in the Software?Nr. 7And how does it look like?Rotational VibrationLets make a DEMO!Nr. 8 automotive engine, development, transmission systems,diff

5、erential test 2WD 4WD,every customer who produces and develops rotating machinesEvery costumer who has to measure rotation parts!Rotational VibrationCustomers?Voice of the customer: A very useful add on which is included in every Dewetron instrument, and it takes only a finger snap to activate it.“

6、Questions?Nr. 9Torsional VibrationCustomer asks? can you measure the twist of my crank shaft? is it possible to measure the slip angle of my clutch? do you have a solution to measure the twist of a power train? Yes!Nr. 10What can we do?The shaft of the engine is broken again? By checking the twist,

7、we can analyse the shaft and improve it.Determine the twist angle of a shaft, or crank shaft of an engine!Torsional VibrationNr. 11What do we need? 2x Pickups/Encoders/RIE-360-RPM sensors with at least 180 pulses/revolution!Torsional VibrationNr. 12How to set it up in the Software? prepared and read

8、y to use template, for easy and fast setup,Torsional VibrationNr. 13How does it look like?Torsional VibrationLets make a DEMO! angle based view time based viewNr. 14automotive engine, development, transmission systems,differential test 2WD 4WD, slip angle of clutches, power couplings,every customer

9、who produces and develops rotating machines!Customers?Voice of the customer: Easy to understand and to setup“ Questions?Torsional VibrationNr. 15Order trackingCustomer asks? Do you have Order tracking? Can you show orders over rpm? Is it possible to get Phase information too? Does it support my: Pic

10、kup-, Analogue-, Encoder- , RIE-360- Sensor ? Draw a waterfall in Order- and Time- domain? Possibility to recalculate the order in Post processing?Yes!Nr. 16What can we do?Order tracking Provide a powerful Order tracking module for the customer! Included in every Dewetron instrument, its simply an o

11、ption to sell, Recalculation in Post processing makes it stronger than ever,. Done in time domain to keep all advantages of it EASY TO USE!Nr. 17rpm channel RIE-360/720 Pickup Encoder CANOrder trackingWhat do we need?channel(s) to be analysedNr. 18 How to set it up in the Software?Order Trackingprep

12、ared and ready to use template, Nr. 19How does it look like?Order TrackingH1 and P1 over rpm RE- and IM- in XYOrder and Frequency domain 3D and 2d plotsNr. 20automotive engine, development, transmission systems,differential test 2WD 4WD, every customer who produces and develops rotating machines!Cus

13、tomers?Voice of the customer: Do you have Ordertracking?“ Questions?Order TrackingNr. 21Orbit ViewCustomer asks? Do you have Orbit view? Can you extract the 1st; 2nd; xxth; harmonic an show it in the orbit ? Can you average a view revolutions?Yes!Nr. 22What can we do?Orbit view Provide the Orbit Dis

14、play Included in every Dewetron instrument Calculation from acceleration to displacement Extract particular harmonic in the orbit view Provide the whole solution Nr. 23rpm channel RIE-360/720 Pickup Encoder CANOrbit viewWhat do we need?2 acceleration channels X and Y direction or1 triaxial sensor fo

15、r X and YNr. 24How to set it up in the Software?Orbit viewAccelerationDisplacementOrder TrackingNr. 25How does it look like?Orbit viewLETs make a DEMO!Nr. 26Paper mills, gas turbinesmovement and displacement of machines, Turbines, Valves, oil bearings,.Customers?Orbit viewNr. 27BalancingCustomer ask

16、s? Do you provide Balancing? Single plane and Dual plane?Yes! Nr. 28What can we do?Balancing Provide the whole measurement and balancing procedure Provide acceleration sensors and tacho probe Included in every instrument Nr. 29rpm channel RIE-360/720 Pickup CAN EncoderBalancingWhat do we need?1 acce

17、leration channel (Single Plane)2 acceleration channels (Dual Plane)Nr. 30How to set it up in the Software?Balancing Acceleration Velocity OrderTrackingInstruction guided Balancing InterfaceLETs make a DEMO!Nr. 31Customers?Balancingevery customer who produces and develops rotating machines!Voice of the customer: Easy to use, I dont like to use my old instruments any more! Zooming, evaluating data, analysing phenomena is fast and straight forward” Reinhard Meisenpichler KOMPTECHQuestions?