H.264 Standalone DVR USER MANUAL

《H.264 Standalone DVR USER MANUAL》由会员分享，可在线阅读，更多相关《H.264 Standalone DVR USER MANUAL（41页珍藏版）》请在装配图网上搜索。

1、 H.264 Standalone DVRUSER MANUAL_V2.139INDEX.Chapter one Products Introduce.21.1 Technical Parameter.21.2 Performance.3Chapter Two Hardware.42.1 H.264 standalone 4CH/8CH/16CH DVR4Chapter Three Operation.103.Operation instruction.103.1.1 Remote control AND Front panel keypad.103.1.2 How to use mouse

2、of DVR (for right hand mouse). 113.2 Powering On.123.3 Shutdown.133.4 Multi Channel.133.5 Preview.143.6 Recording operation.143.7 Playback video.153.8 How to control PTZ.163.9 Alarm control.173.10 Display Adjust.18Chapter Four Menu Operation Guide194.1 Recording Setup.194.2 Camera.214.3 Network Setu

3、p.234.4 System Setup.254.5 System Management.28Chapter Five IE Preview.305.1logging on interface.305.2 System Settings.315.3 State control.34Chapter Six FAQ (Frequently Asked Questions).38 l PowerThis DVR select the adaptor is DC12V; please make sure the power supply voltage before use the machine.I

4、f long time do not use the machine, please turn off the power of DVR machine, and let the electric plug away from power socket;l safetyThis DVR only for indoor use, as for prevent short circuit or electric danger, please do not let the DVR in the raining or humid area.In case any solid or liquid ins

5、ide the case of DVR, please turn off the power immediately, and ask the qualified technician check it before reboot the DVR;The DVR is the precision machine, there is nothing for repair by customers themselves in it, when it break down, please ask the qualified technician to check and repair, or con

6、tact with the agents of it.l InstallationPlease keep the DVR in level for installation;Pay attention to equipment ground;For the first time to install the DVR, please make sure if the hard disk drive install or not;Prevent to open the case and change the hard disk drive in electrified;Propose to sel

7、ect the performance of hard disk drive will be 7200 rotating speed person second; Please select the appropriate installation site, so let the air can be free flow inside the DVR, prevent the machine overheating;Please do not install the DVR nearby the radiator, air chute etc. heat source,or where th

8、e direct sunlight, too much dust, or mechanical vibration or attack; Chapter one Products Introduce1.1 Technical ParameterCompression standardH.264 baseline profileL3.1Video iInput Composite 1.0Vp-p/75,BNC4/ BNC8/ BNC16Video outputComposite 1.0Vp-p/75,BNC1, VGA1 ResolutionPreview D1 704576（PAL），7204

9、80（NTSC） CIF 352288（PAL），320240（NTSC）Recording D1 704576（PAL），720480（NTSC）CIF 352288（PAL），320240（NTSC） Frate ratePreview/ recording4ch 100fps(PAL), 120fps(NTSC8ch 200fps(PAL), 240fps(NTSC) 16ch 400fps(PAL), 480fps(NTSC)Audio input-8dB22k,RCAx4(4ch)Audio output-8dB92dB,RCAx1Audio decodeADPCMAlarm inp

10、utInput low level alarm, user setting normal open or normal close, Varies according to the modelAlarm output1ch output or 2ch output;Varies according to the modelRecording modeManual recording, timing recording , motion detection recording and external alarm recording Simplex/duplex/ triplextriplex(

11、recording, playback , LAN transmission)LANRJ45(10M/100M self-adapting)PTZ controlYesCommunicationRS4851，USB2.02USB USB mouse controlHard disk drive1or2x SATA（2TB or above）Remote control unitYesDimensionMain board size : 220mm x 112mmPower supplyAC110-230V1.2 PerformanceReal-timemonitoringTurn-by-tur

12、n analog video output and VGA interface, according to TVmonitor or VGA monitor to live view in1/4/8/9/16 or more video channel tomonitoring the recording streaming and the record file capacity in Every hours every channel, to presentation the status of video channel, recording, dynamic detection, vi

13、deo loss, monitoring lock-up. You can view the system log in local DVR.StoragefunctionInternal 1or2 SATA interface, MAX2TB hard disk drive, the file of harddisk drive include cover modecirculation recording and none cyclicalrecording, the storage data to use the proprietary format, can not falsify t

14、he data, make sure the data safety.Compression formatVideo compression format: H.264Support 8ch video and audio signal, videoand audio maintaining stability insynchronous.BackupfunctionThrough USB interface to backup. ( for example USB drive and mobile hard disk drive etc.) The video file can be dow

15、nloaded by Client software through LAN to laptop hard disk drive.Recording andplayback function* Multiplex, to achieve real time recording to be independent at the same time to single channel playback, research and backwards, network monitoring, network search download etc.* Multiple recording mode:

16、 Manual, normal, alarm, linkage,dynamic detection recording etc. turn-by-turn pre-recording function.* Can playback the record file in DVRthrough network, to achieve quick-searchthe recording file and recording type,multiple playback type: SLOW, FastForward, Backwards, step Forward.Display the exact

17、 time of event occurred while recording file playback.NetworkOperationfunction* through network to real time remote monitoring;* PTZ control* recording research and real time playback;* system setting parameter modify and the system software upgrade;* remote monitoring alarm process and view the sys

18、tem log message;* to use embedded TCP/IP protocol and Embedded Operation System, can access the DVR through client software program bundle in the package;*Management Model: use enhancement user management, password mode to make sure the valid user to login the system, flexible convenient and fast to

19、 set the different permission user requirement.Alarm linkage function8ch alarm input ( alarm event mode can beset normal open or normal close selection),and turn-by-turn video loss alarm, dynamicdetection alarm, the alarm device may besmoke detection censer, temperaturedetector, IR detector.Possess

20、4ch relay switch alarm output, flexible convenient and fast to achieve alarm linkage and lighting control at site.Theyre possess protective circuit in Alarm input and alarm output port, make sure the device not to damaged.Com-municationport* Possess specific interface, achieve alarm input and PTZ co

21、ntrol;* possess a standard Ethernet interface, achieve the network remote monitoring.PTZcontrol* Support PTZ decoder through RS485 communicate* scalable multiple decoder protocol, easy to achieve to control the pan driver and speed dome camera function.Intelligentoperation* mouse operation function;

22、* In menu for same setting and to process shortcut copy operationChapter Two Hardware2.1H.264 standalone 4CH/8CH/16CH DVR2.1.1 Hard disk InstallationFor the first use, please install the hard diskRemove the screws on both extracted from the next cover up connect hard disk and mother boardsides of sh

23、ellfix the screw of hard disk close cover install the screws on both sides of shell2.1.2 Rear panel4CHItemInterfaceDescription1VIDEO IN4ch video input2AUDIO IN4ch audio input 3V-OUT1ch video output4A-OUT1ch audio output5VGAVGA monitor 6NETRJ45 for internet7USB/ MOUSEFirst USB for backup or upgrade s

24、ystem of DVR; Second USB for mouse8ON/OFFPower supply switcher9DC-12VPower adaptor port 10ALARM IN：1 2 3 4 alarm input portRS-485：A, BALARM OUT: N1 alarm output port, every channel connect GND、OUT、COM;every two channel OUT, COM port is for GND;4CH_HItemInterfaceDescription1VIDEO IN4ch video input2AU

25、DIO IN4ch audio input 3V-OUT1ch video output4A-OUT1ch audio output5VGAVGA monitor 6NETRJ45 for internet7USB/ MOUSEFirst USB for backup or upgrade system of DVR; Second USB for mouse8ON/OFFPower supply switcher9DC-12VPower adaptor port 10ALARM IN：1 2 3 4 alarm input portRS-485：A, BALARM OUT: N1 alarm

26、 output port, every channel connect GND、OUT、COM;every two channel OUT, COM port is for GND;4CH_SItemInterfaceDescription1VIDEO IN4ch video input2AUDIO IN1ch audio input 3V-OUT1ch video output4A-OUT1ch audio output5VGAVGA monitor 6NETRJ45 for internet7USB/ MOUSEFirst USB for backup or upgrade system

27、of DVR; Second USB for mouse8ON/OFFPower supply switcher9DC-12VPower adaptor port 10No AlarmRS-485：A, B8CHItemInterfaceDescription1VIDEO IN8ch video input2AUDIO IN4ch audio input3V-OUT1ch video output4A-OUT1ch audio output5VGAVGA monitor 6NETRJ457USB/ MOUSEFirst USB for backup or upgrade system of D

28、VR; Second USB for mouse8ON/OFFPower supply switcher9DC-12VPower adaptor port 10ALARM IN：IN1-IN8 alarm input portRS-485：A , BALARM OUT: N1 N2 alarm output port, every channel connect GND、OUT、COM;every two channel OUT, COM port is for GND; 8CH_HItemInterfaceDescription1VIDEO IN8ch video input2AUDIO I

29、N8ch audio input3V-OUT1ch video output4A-OUT1ch audio output5VGAVGA monitor 6NETRJ457USB/ MOUSEFirst USB for backup or upgrade system of DVR; Second USB for mouse8ON/OFFPower supply switcher9DC-12VPower adaptor port 10ALARM IN：IN1-IN4 alarm input portRS-485：A , BALARM OUT: N1 alarm output port, ever

30、y channel connect GND、OUT、COM;every two channel OUT, COM port is for GND; 8CH_SItemInterfaceDescription1VIDEO IN8ch video input2AUDIO IN1ch audio input 3V-OUT1ch video output4A-OUT1ch audio output5VGAVGA monitor 6NETRJ457USB/ MOUSEFirst USB for backup or upgrade system of DVR；Second USB for mouse8ON

31、/OFFPower supply switcher9DC-12VPower adaptor port10ALARM IN：A alarm input portRS-485：+, -ALARM OUT: C O alarm output port, every channel connect GND、OUT、COM;, COM port is for GND;16CH ItemInterfaceDescription1VIDEO IN16ch video input2AUDIO IN4ch audio input 3V-OUT1ch video output4A-OUT1ch audio out

32、put5VGAVGA monitor 6NETRJ45 for internet7USB/ MOUSEFirst USB for backup or upgrade system of DVR；Second USB for mouse8ON/OFFPower supply switcher9DC-12VPower adaptor port 10ALARM IN：4CH alarm input portRS-485：A, BALARM OUT: N1 N2 for alarm output port, every channel connect C and O; port is for GND;

33、 16CH_S ItemInterfaceDescription1VIDEO IN16ch video input2AUDIO IN4ch audio input 3V-OUT1ch video output4A-OUT1ch audio output5VGAVGA monitor 6NETRJ45 for internet7USB/ MOUSEFirst USB for backup or upgrade system of DVR；Second USB for mouse8ON/OFFPower supply switcher9DC-12VPower adaptor port 10ALAR

34、M IN：8CH alarm input portRS-485：A, BALARM OUT: N1 N2 for alarm output port, every channel connect C and O;COM port is for GND;2.1.3 Alarm input port 8chanel alarm input, the mode of alarm input is no restriction (possible is normal open also normal close);the GND alarm detector connect to COM under

35、parallel connection (the power of alarm detector supply by external power supply;the ground terminal of alarm detector join-up in parallel with DVR; the NC of alarm detector connect with the input end (alarm) of DVR; when you want to reset the remote alarm of triggered , the +12V power supply of ala

36、rm detector supply by DVR, for example, smoke detector. When you select the external power supply, please share the GND with DVR; Alarm input circuit:Alarm inlet connection:2.1.4 Alarm output port 4 way switching value alarm output, selectable in normally open contact, also selectable in normally cl

37、osed contact, the external alarm device should be need Vcc; Chapter Three Operation3.Operation instruction3.1.1 Remote control AND Front panel keypad Table：S/NKEYpad NameOperating instructionS/NKeypad NameOperating instruction1【POWER】Power ON/OFF11【ENTER】【OK】This button is used as“enter”and“ok” key

38、in most circumstances2【DEV】Select DVR1,2,3,12【SWITCH】Switch capital letter/small letter/symbol input on soft keyboard3【MENU】Access main menu13【MODE】Switching of Lens IRIS/FOCUS/ZOOM modes4【ESC】Exit operation or enter upper menuClose soft keyboardClose current windowExit from current controlReturn to

39、 last menuExit from PTZ control under preview state14【PTZ】Access/exit from PTZ control under preview state15【+/-】Volume or number increase/reduction Select item of the list16【ZOOM IN/OUT】Lens control 5【】Slow playback,1/2, 1/4, 1/8 and single frame play17【MUTE】Mute enable/disable【】Fast playback, 2,4

40、and 8 playback18【09 10+】Digital input Corresponding;Channel is magnified in full screen under preview state【】Playback stop【】Play / Pause19【FN】Short cut6【.t. u】Four-way to move the focal point in main menu, up and down to move in the normal window, to control pan driver to move in the PTZ control win

41、dows20【】Switching of 1/4/8/9/16 Preview mode7【REC】To mode of recording21【ALARM】Alarm reset8【SEARCH】Search for playback time choosing22【CLEAR】Clear alarm9【DISPLAY】Display control2310【Shift】Shift between number key and function key243.1.2 How to use mouse of DVR (for right hand mouse)1Left key single

42、clickTo any function menu icon click the mouse left key into the menu To run the control point out operationChange again select frame or motion detection piece modeClick the assemble frame popping to pull down the listIn the input frame, can select digit, character, lowercase, block letter, left cli

43、ck mouse on the keyboard of character input, thats. say move back, say blank，Shift say switch case . 2Right click mouseRight click mouse, popping the shortcut menu, as follows;。Through the menu can be switching preview screen window mode, start replays, PTZ control. Four pictures playback mode, the

44、point of the right mouse button, Can in a single picture, four pictures, eight pictures (8 road playback), 16 screen (16 road playback), broadcast control switch view show or hide broadcast control bar.3Double click left buttonTo run the ActiveX Control ActiveX special operation, For example, double

45、 click the certain item of record listed file, then the system will playback the segmentrecord video.4Dragging the mouseDepress the left key and dragging the mouse, banding select Motion detection area, depress right key of mouse and Dragging, cancel the banding select area.Dragging playback Progres

46、sBar back and forth to dolly moves, to achieve the playback position adjustment. Dragging the audio and video regulation parameter bar dolly moves, to achieve the parameter adjustment.3.2 Powering On Boot-strapIf【POWER】pilot lamp off, please follow the operation step by step:First step: if the power

47、 does not plug into, please plug into the power, then the DVR-4108 begin to start, by now, if the DVR-4108 still inactive, to enter the next step;Second step: turn on the power supply of the DVR-4108 at the back panel, DVR begins to start.If【POWER】pilot lamp to offer RED, press the 【POWER】key, DVR-4

48、108 begins to start.The video output mode of DVR-4108s the default setting is multi picture channel mode after starting the DVR-4108, if the time of start the DVR-4108 is in the Timing Recording Setting, the DVR-4108 will automatically to start the Timing Recording function, the corresponding channe

49、ls recording pilot lamp will be light, the DVR-4108 is normal operation.ButtonDescriptionButtonDescriptionMain MenuPTZ controlWizard languageAlarm controlMulti channelDisplay setupRecording ControlExitPlaybake Bake upIf before starting, the system not to install hard disk, into the system, will tip:

50、 system didnt detect any hard disk connection!3.3 Shutdown u There are two safety mode for Shutdown Enter【Exit】,select【Power Down】. u Abnormal shutdownThrough the rear panel to shutdown During the DVR-4108 running, directly to turn off the power through the rear panel power switch, please avoid as m

51、uch as possible to do it. (specially while the DVR recording).Directly to pull up the power cable of DVR-4108While the DVR-4108 running, directly to pull up the power cable of DVR-4108, please avoid as much as possible to do it. (specially while the DVR recording).Caution: In some area, the power su

52、pply is irregularity, it will cause the DVR-4108 working not normal-operation, the DVR-4108 will be damaged in serious. In this surroundings, suggest select the stabilized voltage supply.3.4 Multi Channel 1/4/8/9/16 preview screen mode switch 3.5 Preview After log in system of DVR, system will autom

53、atically directly enter the preview mode In the preview picture, you can see the overprint date, time, channel name, if the date and time is not correct show on the picture, re setting the date. There is a alarm input mode icon. (the meaning of every kind of icon as following table)Channel picture a

54、ttention 1Channel is video when channel video pictures showed this symbol2Channel happen when dynamic test, channel video pictures showed this symbol3Channel happen when channel video cover alarm pictures showed this symbol4Channel open sound, the channel video pictures showed this symbol3.6 Recordi

55、ng operation Customer can according to select the different kind of recording mode in this system. For the different kind of recording mode you set, the channel will be showed the mark on everyone channel. Manual recording Note: Manual recording operational requirement the user should have “recordin

56、g” permission. Please make sure the hard disk drive has been installed and it has been formatted. 1）Input manual recording operation menuSingle click right key of mouse or In main menu= recording control can into manual recording operation menu. Under preview mode, press REC key or on the Remote con

57、troller unit key into recording control operation menu, as follows:2) The explanation of manual recording operation menu 【manual recording】 Priority level highest, no matter currently what status of every channel, after carry out the manual press, corresponding channel will be record common in progr

58、ess; 【Auto recording】Setting channel recording by setting condition to record under Timing, Motion detection and Alarm in Recording Setting;【Stop Recording】All video channel stop recording; 3.7 Playback videoButtonDescriptionButtonDescription Synchronous/asynchronous playVoice adjustmentframe by frame1/4/8/9/16 s