1145合金铝箔英文版企业标准

《1145合金铝箔英文版企业标准》由会员分享，可在线阅读，更多相关《1145合金铝箔英文版企业标准（15页珍藏版）》请在装配图网上搜索。

1、TECHNICALDATA SHEET ALUMINIUM FOILVersion: 2005-12-09Supplier: ALCOA SHANGHAI ALUMINIUM PRODUCT 855 Jiang Chuan Road, Minghang District Shanghai 200245 China Tel: 86 21 6430 1730 Material: Aluminum foil, including light gauge (6.30-6.5, 7, 8-9 microns) and 12-16 micra for converter foil purpose, ade

2、quate for lamination, printing, lacquering as well as 20，25，30，40 micra for pharmaceutical.1SPECIFICATIONS ALUMINIUM 6.30-6.50 microns FOIL REMARKS PROPERTYU.O.M *Aluminum Foil, for converter foil purpose, adequate for lamination lacquering, printing as well as household use.ALLOY1145-TEMPERSOFT (O)

3、As ordered: soft(O) Other tempers on request. GAUGEMICRONS6.30-6.50TOLERANCEMICRONS8% on spot measurement.4% on average for lots bigger than 10 tonsThis refers to tolerances around the technical target as set on the mill when rolling.The weighing of sample of known area will be the referred method.S

4、URFACE FINISHBRIGHT/DULLDepending on order, matt or dull side wound to outside.One side bright, one side dull, up to 40mWETTABILITYGRADE (MINIMUM)ACValid for temper O (soft).SPLICESNUMBER (MAXIMUN)Reel Diametermm400600800MAX SPLICEper reel.#246Ultrasonic Welding. Position: longitudinal to spool axia

5、l. Overlapping 5 mm.Marked at the reel end by aluminum flags (10 x 10 mm) each side.PINHOLESNUMBER/SQ.MPinholes/m2 according to EN-546-4Max.300.Selected area for counting pinholes must be representative of the entire surface.TENSILE STRENGTHMPa50ELONGATION%(MIN)1.0OUTSIDE DIAMETERmmFor cores of 3” I

6、.D.(76.2mm) ,Min.300 mm and Max 600mm.For cores of 150152.4 mm I.D., Min. 400 mm and Max. 800 mm. WIDTHmm2501340TOLERANCE 1( up to 1620 mm on customer demand)Width Measurement at 20-25 degrees.TRACE ELEMENTS%Pb0.01 Cd0.01 As0.01The level of the sum of cadmium, lead, mercury and hexavalent chromium i

7、s below 100 ppm.COREAluminum / SteelStandard core extension is 5 mm for each side with no slot on it. CORE I.D.mm76.20.2(Aluminum) / 1510.3(steel)6” cores on Demand.Unwinding PropertiesMax (M)1.5 mMethod for testing stickiness as attached . Length of foil is necessary to cause unwind max. 1.5 m on t

8、he entire length of the coil.Reel LengthM+0 / -5% of the specified length for 90% of the coils.For the remaining 10%, +0 / -20%.Coil EccentricitymmWidth - 1290O.D.- 400 mm34 O.D.400 x 60057* U. O. M UNIT OF MEASURE. 2SPECIFICATIONS ALUMINIUM 7 microns. FOIL REMARK PROPERTYU.O.M *Aluminum Foil, for c

9、onverter foil purpose, adequate for lamination lacquering, printing as well as household use.ALLOY1145-TEMPERSOFT (O)As ordered: soft(O) Other tempers on requestGAUGEMICRONS7.0TOLERANCEMICRONs8% on spot measurement.4% on average for lots bigger than 10 tonsThis refers to tolerances around the techni

10、cal target as set on the mill when rolling.The weighing of sample of known area will be the referred method.SURFACE FINISHBRIGHT/DULLDepending on order, matt or bright side wound to out side.One side bright, one side dull, up to 40mWETTABILITYGRADE (MINIMUM)ACValid for temper O (soft).SPLICESNUMBER

11、(MAXIMUN)Reel Diameter mm400600800Max. Splices per reel. #246Ultrasonic Welding. Position: longitudinal to spool axial. Overlapping 5 mm.Marked at the reel end by aluminum flags (10 x 10 mm) each side.PINHOLESNUMBER/SQ.MPinholes/m2 according to EN-546-4Max.200Selected area for counting pinholes must

12、 be representative of the entire surface.TENSILE STRENGTHMPa50ELONGATION%(MIN)1.0OUTSIDE DIAMETERmm(MAX)For cores of 3” I.D.(76.2mm) ,Min.300 mm and Max 600mm.For cores of 150152.4 mm I.D., Min. 400 mm and Max. 800 mm.WIDTHmm2501340TOLERANCE 1( up to 1620 mm on customer demand)Width Measurement at 2

13、0-25 degrees.TRACE ELEMENTS%Pb0.01 Cd0.01 As0.01The level of the sum of cadmium, lead, mercury and hexavalent chromium is below 100 ppm.COREAluminum / SteelStandard core extension is 5 mm for each side with no slot on it. CORE I.D.mm76.20.2(Aluminum) / 1510.3(steel)6” cores on Demand.Unwinding Prope

14、rtiesMax (M)1.5 mMethod for testing stickiness as attached . Length of foil is necessary to cause unwind max. 1.5 m on the entire length of the coil Reel LengthM+0 / -5% of the specified length for 90% of the coils.For the remaining 10%, +0 / -20%.EccentricitymmWidth - 1290O.D.- 400 mm34 O.D.400 x 6

15、0057U. O. M UNIT OF MEASURE3SPECIFICATIONS ALUMINIUM 8-9 microns. FOILREMARK PROPERTYU.O.M *Aluminum Foil, for converter foil purpose, adequate for lamination lacquering, printing as well as household use.ALLOY1145-TEMPEROAs ordered: soft (O).Other tempers on requestGAUGEMICRONS8-9TOLERANCEMICRONS8%

16、 on spot measurement.4% on average for lots bigger than 10 tonsThis refers to tolerances around the technical target as set on the mill when rolling.The weighing of sample of known area will be the referred method.SURFACE FINISHBRIGHT/DULL Depending on order, dull or bright side wound to out side.On

17、e side bright, one side dull, up to 40mWETTABILITYGRADE (MINIMUM)ACValid for temper O (soft).SPLICESNUMBER (MAXIMUN)Reel diameter mm400600800Max Splices per reel #246Ultrasonic Welding. Position: longitudinal to spool axial. Overlapping 5 mm.Marked at the reel end by aluminum flags (10 x 10 mm) each

18、 side.PINHOLESNUMBER/SQ.mPinholes/m2 according to EN-546-4Max.100Selected area for counting pinholes must be representative of the entire surface.TENSILE STRENGTHMPa50ELONGATION%(MIN)1.0OUTSIDE DIAMETERmm(MAX)For cores of 3” I.D.(76.2mm) ,Min.300 mm and Max 600mm.For cores of 150152.4 mm I.D., Min.

19、400 mm and Max. 800 mm.WIDTHmm2501340TOLERANCE 1( up to 1620 mm on customer demand)Width Measurement at 20-25 degrees.TRACE ELEMENTS%Pb0.01 Cd0.01 As0.01The level of the sum of cadmium, lead, mercury and hexavalent chromium is below 100 ppm.COREAluminum / SteelStandard core extension is 5 mm for eac

20、h side with no slot on it. CORE I.D.mm76.20.2(Aluminum) / 1510.3(steel)6” cores on Demand.Unwinding PropertiesMax (M)1.5 mMethod for testing stickiness as attached . Length of foil is necessary to cause unwind max. 1.5 m on the entire length of the coil Reel LengthM+0 / -5% of the specified length f

21、or 90% of the coils.For the remaining 10%, +0 / -20%.EccentricitymmWidth - 1290O.D.- 400 mm34 O.D.400 x 60057* U. O. M UNIT OF MEASURE4SPECIFICATIONS ALUMINIUM 12-16 microns. FOIL REMARK PROPERTYU.O.M *Aluminum Foil, for converter foil purpose, adequate for lamination lacquering, printing as well as

22、 household use.ALLOY1145-TEMPERSOFT (O)As ordered: soft (O).Other tempers on request. GAUGEMICRONS12-16TOLERANCEMICRONS8% on spot measurement.4% on average for lots bigger than 10 tonsThis refers to tolerances around the technical target as set on the mill when rolling.The weighing of sample of know

23、n area will be the referred method.SURFACE FINISHBRIGHT/DULLDepending on order, dull or bright side wound to out side.One side bright, one side dull, up to 40mWETTABILITYGRADE (MINIMUM)ACValid for temper O (soft).SPLICESNUMBER (MAXIMUN)Reel diametermm400600800Max. Splices per reel #235Ultrasonic Wel

24、ding. Position: longitudinal to spool axial. Overlapping 5 mm.Marked at the reel end by aluminum flags (10 x 10 mm) each side.PINHOLESNUMBER/SQ.mPinholes/m2 according to EN-546-4Max.20Selected area for counting pinholes must be representative of the entire surface.TENSILE STRENGTHMPa50ELONGATION%(MI

25、N)1.0OUTSIDE DIAMETERmm(MAX)For cores of 3” I.D.(76.2mm) ,Min.300 mm and Max 600mm.For cores of 150152.4 mm I.D., Min. 400 mm and Max. 800 mm.WIDTHmm2501340TOLERANCE 1( up to 1620 mm on customer demand)Measurement at 20-25 degrees.TRACE ELEMENTS%Pb0.01 Cd0.01 As0.01The level of the sum of cadmium, l

26、ead, mercury and hexavalent chromium is below 100 ppm.COREAluminum / SteelStandard core extension is 5 mm for each side with no slot on it. CORE I.D.mm76.20.2(Aluminum) / 1510.3(steel)6” cores on Demand.Unwinding PropertiesMax (M)1.5 mMethod for testing stickiness as attached . Length of foil is nec

27、essary to cause unwind max. 1.5 m on the entire length of the coil Reel LengthM+0 / -5% of the specified length for 90% of the coils.For the remaining 10%, +0 / -20%.EccentricitymmWidth - 1290O.D.- 400 mm34 O.D.400 x 60057* U. O. M UNIT OF MEASURE5SPECIFICATIONS ALUMINIUM 20 microns FOIL REMARKS PRO

28、PERTYU.O.M *Aluminum Foil, for converter foil purpose, adequate for lamination lacquering, printing as well as household use.ALLOY1145/8011-TEMPERH18As ordered: soft(O) Other tempers on request. GAUGEMICRONS20TOLERANCEMICRONS8% on spot measurement.4% on average for lots bigger than 10 tonsThis refer

29、s to tolerances around the technical target as set on the mill when rolling.The weighing of sample of known area will be the referred method.SURFACE FINISHBRIGHT/DULLDepending on order, matt or dull side wound to outside.One side bright, one side dull, up to 40mWETTABILITYGRADE (MINIMUM)-Valid for t

30、emper O (soft).SPLICESNUMBER (MAXIMUN)Reel Diametermm400600800MAX SPLICEper reel.#234Ultrasonic Welding. Position: longitudinal to spool axial. Overlapping 5 mm.Marked at the reel end by aluminum flags (10 x 10 mm) each side.PINHOLESNUMBER/SQ.MPinholes/m2 according to EN-546-4Max.3.Selected area for

31、 counting pinholes must be representative of the entire surface.TENSILE STRENGTHMPa1145:160; 8011:170ELONGATION%(MIN)1145:0.5; 80111.0OUTSIDE DIAMETERmmFor cores of 3” I.D.(76.2mm) ,Min.350 mm and Max 600mm.For cores of 150152.4 mm I.D., Min. 400 mm and Max. 760 mmWIDTHmm2501450TOLERANCE 1Width Meas

32、urement at 20-25 degrees.TRACE ELEMENTS%Pb0.01 Cd0.01 As0.01The level of the sum of cadmium, lead, mercury and hexavalent chromium is below 100 ppm.COREAluminum / SteelStandard core extension is 5 mm for each side with no slot on it. CORE I.D.mm76.20.2(Aluminum) / 1510.3(steel)6” cores on Demand.Unw

33、inding PropertiesMax (M)1.5 mMethod for testing stickiness as attached . Length of foil is necessary to cause unwind max. 1.5 m on the entire length of the coil.Reel LengthM+0 / -5% of the specified length for 90% of the coils.For the remaining 10%, +0 / -20%.* U. O. M UNIT OF MEASURE. 6SPECIFICATIO

34、NS ALUMINIUM 25 microns FOIL REMARKS PROPERTYU.O.M *Aluminum Foil, for converter foil purpose, adequate for lamination lacquering, printing as well as household use.ALLOY1145/8011-TEMPERH18As ordered: soft(O) Other tempers on request. GAUGEMICRONS25TOLERANCEMICRONS8% on spot measurement.4% on averag

35、e for lots bigger than 10 tonsThis refers to tolerances around the technical target as set on the mill when rolling.The weighing of sample of known area will be the referred method.SURFACE FINISHBRIGHT/DULLDepending on order, matt or dull side wound to outside.One side bright, one side dull, up to 4

36、0mWETTABILITYGRADE (MINIMUM)-Valid for temper O (soft).SPLICESNUMBER (MAXIMUN)Reel Diametermm400600800MAX SPLICEper reel.#123Ultrasonic Welding. Position: longitudinal to spool axial. Overlapping 5 mm.Marked at the reel end by aluminum flags (10 x 10 mm) each side.PINHOLESNUMBER/SQ.MPinholes/m2 acco

37、rding to EN-546-4No PinholesSelected area for counting pinholes must be representative of the entire surface.TENSILE STRENGTHMPa1145:160; 8011:170ELONGATION%(MIN)1145:0.5; 80111.0OUTSIDE DIAMETERmmFor cores of 3” I.D.(76.2mm) ,Min.350 mm and Max 600mm.For cores of 150152.4 mm I.D., Min. 400 mm and M

38、ax. 760 mmWIDTHmm2501450TOLERANCE 1Width Measurement at 20-25 degrees.TRACE ELEMENTS%Pb0.01 Cd0.01 As0.01The level of the sum of cadmium, lead, mercury and hexavalent chromium is below 100 ppm.COREAluminum / SteelStandard core extension is 5 mm for each side with no slot on it. CORE I.D.mm76.20.2(Al

39、uminum) / 1510.3(steel)6” cores on Demand.Unwinding PropertiesMax (M)1.5 mMethod for testing stickiness as attached . Length of foil is necessary to cause unwind max. 1.5 m on the entire length of the coil.Reel LengthM+0 / -5% of the specified length for 90% of the coils.For the remaining 10%, +0 /

40、-20%.* U. O. M UNIT OF MEASURE. SPECIFICATIONS ALUMINIUM 30 microns FOIL 7REMARKS PROPERTYU.O.M *Aluminum Foil, for converter foil purpose, adequate for lamination lacquering, printing as well as household use.ALLOY8011-TEMPEROAs ordered: soft(O) Other tempers on request. GAUGEMICRONS30TOLERANCEMICR

41、ONS8% on spot measurement.4% on average for lots bigger than 10 tonsThis refers to tolerances around the technical target as set on the mill when rolling.The weighing of sample of known area will be the referred method.SURFACE FINISHBRIGHT/DULLDepending on order, matt or dull side wound to outside.O

42、ne side bright, one side dull, up to 40mWETTABILITYGRADE (MINIMUM)AValid for temper O (soft).SPLICESNUMBER (MAXIMUN)Reel Diametermm400600800MAX SPLICEper reel.#012Ultrasonic Welding. Position: longitudinal to spool axial. Overlapping 5 mm.Marked at the reel end by aluminum flags (10 x 10 mm) each si

43、de.PINHOLESNUMBER/SQ.MPinholes/m2 according to EN-546-4No PinholesSelected area for counting pinholes must be representative of the entire surface.TENSILE STRENGTHMPa60ELONGATION%(MIN)2.0OUTSIDE DIAMETERmmFor cores of 3” I.D.(76.2mm) ,Min.350 mm and Max 600mm.For cores of 150152.4 mm I.D., Min. 400

44、mm and Max. 760 mmWIDTHmm2501450TOLERANCE 1Width Measurement at 20-25 degrees.TRACE ELEMENTS%Pb0.01 Cd0.01 As0.01The level of the sum of cadmium, lead, mercury and hexavalent chromium is below 100 ppm.COREAluminum / SteelStandard core extension is 5 mm for each side with no slot on it. CORE I.D.mm76

45、.20.2(Aluminum) / 1510.3(steel)6” cores on Demand.Unwinding PropertiesMax (M)1.5 mMethod for testing stickiness as attached . Length of foil is necessary to cause unwind max. 1.5 m on the entire length of the coil.Reel LengthM+0 / -5% of the specified length for 90% of the coils.For the remaining 10

46、%, +0 / -20%.* U. O. M UNIT OF MEASURE. SPECIFICATIONS ALUMINIUM 40 microns FOIL 8REMARKS PROPERTYU.O.M *Aluminum Foil, for converter foil purpose, adequate for lamination lacquering, printing as well as household use.ALLOY8011-TEMPEROAs ordered: soft(O) Other tempers on request. GAUGEMICRONS40TOLER

47、ANCEMICRONS8% on spot measurement.4% on average for lots bigger than 10 tonsThis refers to tolerances around the technical target as set on the mill when rolling.The weighing of sample of known area will be the referred method.SURFACE FINISHBRIGHT/DULLDepending on order, matt or dull side wound to o

48、utside.One side bright, one side dull, up to 40mWETTABILITYGRADE (MINIMUM)AValid for temper O (soft).SPLICESNUMBER (MAXIMUN)Reel Diametermm400600800MAX SPLICEper reel.#012Ultrasonic Welding. Position: longitudinal to spool axial. Overlapping 5 mm.Marked at the reel end by aluminum flags (10 x 10 mm)

49、 each side.PINHOLESNUMBER/SQ.MPinholes/m2 according to EN-546-4No PinholesSelected area for counting pinholes must be representative of the entire surface.TENSILE STRENGTHMPa60ELONGATION%(MIN)2.0OUTSIDE DIAMETERmmFor cores of 3” I.D.(76.2mm) ,Min.350 mm and Max 600mm.For cores of 150152.4 mm I.D., M

50、in. 400 mm and Max. 760 mmWIDTHmm8001450TOLERANCE 1Width Measurement at 20-25 degrees.TRACE ELEMENTS%Pb0.01 Cd0.01 As0.01The level of the sum of cadmium, lead, mercury and hexavalent chromium is below 100 ppm.COREAluminum / SteelStandard core extension is 5 mm for each side with no slot on it. CORE

51、I.D.mm76.20.2(Aluminum) / 1510.3(steel)6” cores on Demand.Unwinding PropertiesMax (M)1.5 mMethod for testing stickiness as attached . Length of foil is necessary to cause unwind max. 1.5 m on the entire length of the coil.Reel LengthM+0 / -5% of the specified length for 90% of the coils.For the rema

52、ining 10%, +0 / -20%.* U. O. M UNIT OF MEASURE. Quality Record Specifications9Each shipmentFor each shipment Alcoa Shanghai shall send separately a quality record with the following information:-.Company name- Order number- Customer order number- Customer material number- Date of shipment- Ordered t

53、hickness- Ordered widthEach reelFor each reel listed in the record:- Reel id number- Net weight- Thickness- Alloy- Width Disposition of Defective Foil- Incoming shipments are to be examined before unloading. When damaged rolls are discovered, if carrier is responsible, notation is made on freight bi

54、ll before material is removed, and signed by driver and receiver. If rolls are intact and show no sign of rough handling by carrier, but still appear to have damage, the condition should be reported immediately to the shipping plant for disposition;- Rejected metal, when returned, must have the Foil

55、 Roll identification Ticket attached;- When possible, samples showing the problem should be attached to the roll and forwarded to supplier;- Detection and complaint shall be made to the producing plant within 90 days of receipt of foil, except in the case of corrosion when the time limit is 60 days;

56、 - Supplier has the right to make an inspection of the rejected foil prior to authorizing a return.Packing SpecificationsQuantities - As specified on the purchase order with a tolerance of 10% unless otherwise stated on the order.Packaging - Foil rolls are to be suspended in steel racks or in wooden

57、 boxes and shall be packed in such a manner that normal handling by common carrier will ensure safe transportation without damage to foil. This includes wrapping to protect foil from water stain and corrosionIdentification - Each rack or box in a shipment shall have its own unique identification num

58、ber clearly visible from both ends of rack or box. Further, each rack or box and each individual roll shall be identified with the following:A.Order number (Release No.)B.Part numberC.Gauge (mm)D.Width (mm)E.Net weight (Kgs)F.Number of splicesG. Alloy, Temper.H.Roll identification number (traceable

59、to source, or point at which composition was determined)Porosity in Foil Rolling 1. Terms and definitions10For the purposes of this European Standard, the following terms and definitions apply.1.1 pinholesRandomly distributed voids in foil of gauge 6 m to 20 m of normally round or oval shape with a

60、maximum dimension up to and including 0,20 mm1.2 perforationsVoids with a maximum dimension of more than 0,20 mm which occur arbitrarily throughout the rolled coil length1.3 roll holesVoids with a maximum dimension of more than 0,20 mm which recur at regular intervals throughout the rolled coil leng

61、th2. Application of special property testingThe applicability of tests for special properties of foil products is given in Table 1.The tests shall only be carried out when agreed between supplier and purchaser and stated on the order.3.1 Principle of testAs rolled foil is examined by using a light b

62、ox in an area of low illumination. Porosity is seen as light points against the dark foil surface.The light box, consists of translucent glass, lit from below by a luminous source giving an even illumination of 1 000 lux to 1 500 lux. The size of the light box is determined by the dimension of the l

63、argest foil sample to be examined.3.2 Test methodDim the light in the room in which the test is carried out to 20 lux to 50 lux.Place the foil test sample on the light box with its matt surface facing the observer. Mask the area of the light box not covered by the test sample. Observe the test sampl

64、e from a distance of approximately 0,5 m.The test area shall be selected by one of the following methods:a) Random selection: A sample of 1 m2 is selected at random;b) Worst area selection: A sample of 1 dm2 is selected from the area exhibiting the highest porosity (worst field). Count the number of

65、 pinholes, perforations or roll holes in the sample. Ignore pinholes less than 0,020 mm in diameter.For the random selection sample, count the number of voids in 1 m2. For the worst area selection sample, count the number of voids in 1 dm2. Report separately the number of pinholes, perforations and

66、roll holes per unit area.3.3 Acceptance valuesThe maximum acceptable number of pinholes, perforations and roll holes shall be agreed between supplier and purchaser.3.4 Sampling and frequency of testingOne full width test sample at correct nominal gauge measuring approximately 1 m in length along the rolling direction shall be taken and tested from every three rolled coils.Measurement of Foil Wettability 111. Wettability1.1 Principle of testThe test shall apply to aluminium foil in the gauge rang