射频通信术语中英文对照词汇

上传人:仙*** 文档编号:28640526 上传时间:2021-09-04 格式:DOC 页数:36 大小:695.04KB
收藏 版权申诉 举报 下载
射频通信术语中英文对照词汇_第1页
第1页 / 共36页
射频通信术语中英文对照词汇_第2页
第2页 / 共36页
射频通信术语中英文对照词汇_第3页
第3页 / 共36页
资源描述:

《射频通信术语中英文对照词汇》由会员分享,可在线阅读,更多相关《射频通信术语中英文对照词汇(36页珍藏版)》请在装配图网上搜索。

1、附錄A. 申请者自我宣告之检验项目检验项目测试参考GSM 11.10-1ETS 300 607-1测试结果符合与否(Yes/No)备注Transmitter发射机Intermodulation attenuation互调衰减13.5Receiver接收机Bad frame indication劣讯框指示14.1Reference sensitivity参考灵敏度14.2Usable receiver input level range可用接收机输入位准范围14.3Co-channel rejection同频道排斥14.4Adjacent channel rejection邻频道排斥14.5In

2、termodulation rejection互调排斥14.6Blocking and spurious response阻塞及混附波响应14.7AM suppressionAM抑制14.8Paging performance at high input levels高输入位准呼叫效能14.9Other tests of the layer 1第1层之其它测试Timing advance and absolute delay时间超前及绝对延迟15Reception time tracking speed接收时间追踪速率16Access times during handover交递间之撷取时间

3、17Temporary reception gaps瞬时接收间隙18Channel release after unrecoverable errors无法恢复失误后之频道释出19Cell selection and reselection细胞选取及重选20Received signal measurements接收信号量测21Transmit power control timing and confirmation发射功率控制定时及确认22Single frequency reference单频参考23Tests of the layer 2第2层测试Initialization初始化No

4、rmal Initialization标称初始化25.2.1.1.1Loss of UA frameUA讯框损失25.2.1.1.2.1UA frame with different information field不同讯息领域之UA讯框25.2.1.1.2.2Information frame and supervisory frames in response to an SABM frame响应SABM讯框之信息讯框及监视讯框25.2.1.1.2.3Initialization denial初始化之拒绝25.2.1.1.3Total initialization failure全部初始

5、化之失败25.2.1.1.4Normal initialization without contention resolution标称初始化不含争议部份25.2.1.2Initialization failure初始化失败25.2.1.2.2Normal information transfer标称讯息移转Sequence counting and 1 frame acknowledges连续计次及讯框1之接受25.2.2.1Receipt of an 1 frame in the timer recovery state在定时器恢复状态下讯框1的接收25.2.2.2Segmentation

6、and concatenation区隔与连结25.2.2.3Normal layer 2 disconnection标称第2层断讯25.2.3Test of link failure联机失败测试1 frame loss (MS to SS)讯框1的遗失(MS至SS)25.2.4.1RR response frame loss (MS to SS)RR响应讯框的遗失(MS至SS)25.2.4.3Test of frame transmission with incorrect C/R values不正确C/R值讯框传输测试1 frame with C bit set to zero讯框1含C位设

7、定为零25.2.5.1SABM frame with C bit set to zeroSABM讯框含C位设定为零25.2.5.2Test of errors in the control field在控制范围内之失误测试N(S) sequence errorN(S)连续失误25.2.6.1N(R)sequence errorN(R)连续失误25.2.6.2Improper F bit不适当F位25.2.6.3Test on receipt of Invalid frames失效讯框接收之测试25.2.7Tests of the layer 3第3层测试Initial Tests初始测试Cha

8、nnel request / initial time频道请求/初始时间26.2.1.1Channel request / repetition time频道请求/重复时间26.2.1.2.1Channel request / random reference频道请求/随机参考26.2.1.3IMSI detach and IMSI attachIMSI不附加及附加26.2.2Sequenced MM / CM message transfer连续MM/CM讯息移转26.2.3Establishment cause建立原因26.2.4Test of MS functions in idle m

9、odeMS功能在空闲模式之测试MS indication of available PLMNs有效之PLMNs之MS指示26.3.2MS will send only if BSS is “on air”MS将发送仅于BSS是正播送中26.3.3Manual mode of PLMN selectionPLMN选取之手动模式26.3.4Handling of unknown, unforeseen, and erroneous protocol data, and of parallel transactions未知、未见、失误信令数据及平行交易之处理TI and skip indicator

10、 / RR / Idle ModeTI及跳过省略指示/RR/空闲模式26.5.2.1.1TI and skip indicator / RR / RR-Connection establishedTI及跳过省略指示/RR/RR-连结建立26.5.2.1.2TI and skip indicator / MMTI及跳过省略指示/MM26.5.2.2TI and skip indicator / CCTI及跳过省略指示/CC26.5.2.3Undefined or unexpected message type / undefined message type / CC未定义或不期望讯息型式/未定

11、义讯息型式/CC26.5.3.1Undefined or unexpected message type / undefined message type / MM未定义或不期望讯息型式/未定义讯息型式/MM26.5.3.2Undefined or unexpected message type / undefined message type / RR未定义或不期望讯息型式/未定义讯息型式/RR26.5.3.3Undefined or unexpected message type / unexpected message type / CC未定义或不期望讯息型式/不期望讯息型式/CC26.

12、5.3.4Unforeseen information elements in the non-imperative message part / duplicated information未见讯息组件在不适当之信息部份/复制讯息26.5.4.1Non-semantical mandatory IE errors / RR / missing mandatory IE error / special case非语意必备IE失误/RR/失踪必备IE失误/一般状况26.5.5.1.1.1Non-semantical mandatory IE errors / RR / missing manda

13、tory IE error / general case 非语意必备IE失误/RR/失踪必备IE失误/一般状况26.5.5.1.1.2Non-semantical mandatory IE errors / RR / comprehension required 非语意必备IE失误/RR/失踪必备IE失误/综合性需求26.5.5.1.2Non-semantical mandatory IE errors / MM / syntactically incorrect mandatory IE非语意必备IE失误/MM/综合非正确必备IE26.5.5.2.1Non-semantical mandat

14、ory IE errors / MM / comprehension required 非语意必备IE失误/MM/综合性需求26.5.5.2.3Non-semantical mandatory IE errors / CC / missing mandatory IE / disconnect message非语意必备IE失误/CC/失踪必备IE/断讯讯息26.5.5.3.1.1Non-semantical mandatory IE errors / CC / missing mandatory IE / general case非语意必备IE失误/CC/失踪必备IE/一般状况26.5.5.3

15、.1.2Non-semantical mandatory IE errors / CC / comprehension required非语意必备IE失误/CC/综合性需求26.5.5.3.2Unknown IE, comprehension not required/ MM / IE unknown in the message 未知IE,综合性不需求/M/讯息中IE未知26.5.6.1.2Unknown information elements in the non-imperative message part / CC / Call establishment在非适当讯息中未知IE信息

16、组件/通话建立26.5.6.2.1Unknown information elements in the non-imperative message part / CC / release在非适当讯息中未知IE信息组件/释出26.5.6.2.3Unknown information elements in the non-imperative message part / CC / release complete在非适当讯息中未知IE信息组件/完全释出26.5.6.2.4Spare bits / RR / paging channel备份位/RR/呼叫频道26.5.7.1.1Spare b

17、its / RR / BCCH备份位/RR/BCCH26.5.7.1.2Spare bits / RR / AGCH备份位/RR/AGCH26.5.7.1.3Spare bits / RR / Connected Mode备份位/RR/连接模式26.5.7.1.4Spare bits / MM备份位/MM26.5.7.2Spare bits / CC备份位/CC26.5.7.3Test of the elementary procedures for radio resource management无线资源管理基本程序测试Immediate assignment / SDCCH or TCH

18、 assignment立即指配/SDCCH或TCH指配26.6.1.1Immediate assignment / extended assignment立即指配/延伸指配26.6.1.2Immediate assignment / assignment rejection立即指配/指配拒绝26.6.1.3Immediate assignment / Ignore assignment立即指配/忽略指配26.6.1.4Immediate assignment after immediate assignment reject立即指配拒绝后之立即指配26.6.1.5Paging / normal

19、 / type 1呼叫/标称/型式126.6.2.1.1Paging / normal / type 2呼叫/标称/型式226.6.2.1.2Paging / normal / type 3呼叫/标称/型式326.6.2.1.3Paging / extended呼叫/延伸 26.6.2.2Paging / reorganization / procedure 1呼叫/确认/步骤126.6.2.3.1Paging / reorganization / procedure 2呼叫/确认/步骤226.6.2.3.2Paging / multislot CCCH呼叫/多时槽CCCH26.6.2.5Me

20、asurement / no neighbours量测/无相邻细胞26.6.3.1Measurement / all neighbours present 量测/所有相邻细胞出现26.6.3.2Measurement / barred cells and non-permitted NCCs量测/禁发细胞及非许可NCCs26.6.3.3Measurement / DTX量测/DTX26.6.3.4Measurement / Frequency Formats量测/频率格式26.6.3.5Measurement / multiband environment量测/多频环境26.6.3.6Dedi

21、cated assignment / successful case专用指配/成功状态26.6.4.1Dedicated assignment / failure / failure during active state专用指配/失败/执行状态中失败26.6.4.2.1Dedicated assignment / failure / general case专用指配/失败/一般状况26.6.4.2.2Handover / successful / active call / non-synchronized交递/成功/通话中/异步26.6.5.1Handover / successful /

22、 call under establishment / non-synchronized交递/成功/建立通话中/异步26.6.5.2Handover/ successful / active call / finely synchronized交递/成功/通话中/完全同步26.6.5.3Handover / successful / call under establishment / finely synchronized交递/成功/建立通话中/完全同步26.6.5.4Handover / successful / active call / pre-synchronized / Timin

23、g Advance IE not included交递/成功/通话中/预同步/时间超前不含IE26.6.5.5.1Handover / successful / call being established / pre-synchronized / timing advance IE is included / reporting of observed time difference requested.交递/成功/通话中/预同步/时间超前含IE/需要时间差异观察之报告26.6.5.5.2Handover / successful / active call / pseudo synchro

24、nized交递/成功/通话中/伪同步26.6.5.6Handover / successful / active call / non-synchronized / reporting of observed time difference requested交递/成功/通话中/异步/时间超前含IE/需要时间差异观察之报告26.6.5.7Handover / layer 3 failure交递/第3层失败26.6.5.8Handover / layer 1 failure交递/第1层失败26.6.5.9Frequency redefinition频率重新定义26.6.6.1Test of th

25、e channel mode modify procedure / full rate频道模式修正步骤之测试/全速率26.6.7.1Test of the channel mode modify procedure / half rate频道模式修正步骤之测试/半速率26.6.7.2Ciphering mode / start ciphering保密模式/开始保密26.6.8.1Ciphering mode / no ciphering保密模式/禁止保密26.6.8.2Ciphering mode / old cipher key保密模式/旧保密键26.6.8.3Ciphering mode

26、/ change of mode, algorithm and key保密模式/模式变更,计算法则及键26.6.8.4Ciphering mode / IMEISV request保密模式/IMEISV需求26.6.8.5Classmark changeClassmark变更26.6.11.1Classmark interrogationClassmark疑问26.6.11.2Channel release / SDCCH频道释出/ / SDCCH26.6.12.1Channel release / SDCCH - no L2 ACK频道释出/ SDCCH - no L2 ACK26.6.12

27、.2Channel release / TCH-F频道释出/ / TCH-F26.6.12.3Channel release / TCH-F - no L2 ACK频道释出/ TCH-F - no L2 ACK26.6.12.4Dedicated assignment with starting time / successful case / time not elapsed 专用频道指配含起始时间/成功状况/时间暂停26.6.13.1Dedicated assignment with starting time / successful case / time elapsed专用频道指配含

28、起始时间/成功状况/时间进行26.6.13.2Dedicated assignment with starting time and frequency redefinition / failure case / time not elapsed专用频道指配含起始时间及频率重新定义/失败状况/时间暂停26.6.13.3Dedicated assignment with starting time and frequency redefinition / failure case / time elapsed 专用频道指配含起始时间及频率重新定义/失败状况/时间进行26.6.13.4Handov

29、er with starting time / successful case / time not elapsed交递含起始时间/成功状况/时间暂停26.6.13.5Handover with starting time / successful case / time elapsed交递含起始时间/成功状况/时间进行26.6.13.6Handover with starting time and frequency redefinition / failure case / time not elapsed 交递含起始时间及频率重定义/失败状况/时间暂停26.6.13.7Handover

30、with starting time and frequency redefinition / failure case / time elapsed交递含起始时间及频率重新定义/失败状况/时间进行26.6.13.8Immediate assignment with starting time / successful case / time not elapsed 立即指配含起始时间/成功状况/时间暂停26.6.13.9Immediate assignment with starting time / successful case / time elapsed 立即指配含起始时间/成功状况

31、/时间进行26.6.13.10Elementary procedures of mobility management行动管理的基本程序TMSI reallocationTMSI重新指配26.7.1Authentication accepted 辨识接受26.7.2.1Authentication rejected 辨识拒绝26.7.2.2General Ientification一般确认26.7.3.1Location updating / accepted位置更新/接受26.7.4.1Location updating / rejected / IMSI invalid位置更新/拒绝/IM

32、SI无效26.7.4.2.1Location updating / rejected / PLMN not allowed 位置更新/拒绝/PLMN不被许可26.7.4.2.2Location updating / rejected / location area not allowed 位置更新/拒绝/漫游区域不被许可26.7.4.2.3Location updating / rejected / roaming not allowed in this location area位置更新/拒绝/漫游在该位置区域不被许可26.7.4.2.4Location updating / abnorma

33、l cases / random access fails位置更新/不正常状况/随机撷取失败26.7.4.3.1Location updating / abnormal cases / attempt counter less or equal to 4, LAI different 位置更新/不正常状况/企图上网计数4,不同LAI26.7.4.3.2Location updating / abnormal cases / attempt counter equal to 4位置更新/不正常状况/企图上网计数=426.7.4.3.3Location updating / abnormal ca

34、ses / attempt counter lesequal to 4, stored LAI equal to broadcast LAI位置更新/不正常状况/企图上网计数4,储存LAI等于广播LAI26.7.4.3.4Location updating / release / expiry of T3240位置更新/释出频道/T3240过期26.7.4.4Location updating / periodic spread位置更新/周期式展开26.7.4.5.1Location updating / periodic normal / test 1位置更新/周期式正常/测试126.7.4

35、.5.2Location updating / periodic normal / test 2位置更新/周期式正常/测试226.7.4.5.3Location updating / periodic HPLMN search / MS waits time T位置更新/周期式搜寻HPLMN/MS等待时间T26.7.4.5.4.1Location updating / periodic HPLMN search / MS in manual mode位置更新/周期式搜寻HPLMN/MS手动模式26.7.4.5.4.2Location updating / periodic HPLMN sear

36、ch / MS waits at least two minutes and at most T minutes位置更新/周期式搜寻HPLMN/MS等待至少2分钟并占T分钟大部份26.7.4.5.4.3Location updating / interworking of attach and periodic位置更新/附加及周期式互动工作26.7.4.6MM connection / establishment with cipherMM联机/以保密方式建立26.7.5.2MM connection / establishment without cipherMM联机/非以保密方式建立26.

37、7.5.3MM connection / establishment rejected MM联机/建立被拒绝26.7.5.4MM connection / establishment rejected cause 4MM联机/建立被拒绝原因426.7.5.5MM connection / expiry T3230MM联机/T3230过期26.7.5.6MM connection / abortion by the network / cause #6MM联机/被网络抛弃/原因#626.7.5.7.1MM connection / abortion by the network / cause

38、not equal to #6MM联机/被网络抛弃/原因不等于#626.7.5.7.2MM connection / follow-on request pending / test 1MM联机/后继请求等候/测试126.7.5.8.1MM connection / follow-on request pending / test 2MM联机/后继请求等候/测试226.7.5.8.2MM connection / follow-on request pending / test 3MM联机/后继请求等候/测试326.7.5.8.3Tests related to circuit switche

39、d call control与电路交换通话控制之有关测试Outgoing call / U0 null state / MM connection requested 去话/U0空态/MM联机请求26.8.1.2.1.1Outgoing call / U0.1 MM connection pending去话/U0.1MM联机等待26.8.1.2.2.1Outgoing call / U0.1 MM connection pending / CM service accepted去话/U0.1MM联机等待/CM服务接受26.8.1.2.2.2Outgoing call / U0.1 MM con

40、nection pending / lower layer failure去话/U0.1MM联机等待/较低层讯号失败26.8.1.2.2.3Outgoing call / U1 call initiated / receiving CALL PROCEEDING去话/U1发话/接收CALL PROCEEDING26.8.1.2.3.1Outgoing call / U1 call initiated / rejecting with RELEASE COMPLETE去话/U1发话/拒绝含RELEASE COMPLETE26.8.1.2.3.2Outgoing call / U1 call in

41、itiated / T303 expiry去话/U1发话/T303过期26.8.1.2.3.3Outgoing call / U1 call initiated / lower layer failure去话/U1发话/较低层讯号失败26.8.1.2.3.4Outgoing call / U1 call initiated / receiving ALERTING去话/U1发话/接收ALERTING26.8.1.2.3.5Outgoing call / U1 call initiated / entering state U10去话/U1发话/输入状态U1026.8.1.2.3.6Outgoi

42、ng call / U1 call initiated / unknown message received 去话/U1发话/未知讯息接收26.8.1.2.3.7Outgoing call / U3 MS originating call proceeding / ALERTING received去话/ U3 MS发话进行/ALERTING接收26.8.1.2.4.1Outgoing call / U3 MS originating call proceeding / CONNECT received去话/ U3 MS发话进行/ CONNECT接收26.8.1.2.4.2Outgoing c

43、all / U3 MS originating call proceeding / PROGRESS received without in band information去话/ U3 MS发话进行/ PROGRESS接收,但无频带内信息26.8.1.2.4.3Outgoing call / U3 MS originating call proceeding / PROGRESS with in band information去话/ U3 MS发话进行/ PROGRESS接收,但具频带内信息26.8.1.2.4.4Outgoing call / U3 MS originating call

44、 proceeding / DISCONNECT with in band tones去话/ U3 MS发话进行/ DISCONNECT接收,但具频带内音频26.8.1.2.4.5Outgoing call / U3 MS originating call proceeding / DISCONNECT without in band tones去话/ U3 MS发话进行/ DISCONNECT接收,但无频带内音频26.8.1.2.4.6Outgoing call / U3 MS originating call proceeding / RELEASE received去话/ U3 MS发话

45、进行/ RELEASE接收26.8.1.2.4.7Outgoing call / U3 MS originating call proceeding / termination requested by user去话/ U3 MS发话进行/用户通话请求结束26.8.1.2.4.8Outgoing call / U3 MS originating call proceeding / traffic channel allocation 去话/ U3 MS发话进行/话务频道指配26.8.1.2.4.9Outgoing call / U3 MS originating call proceeding

46、 / timer T310 time-out去话/ U3 MS发话进行/定时器T310暂停26.8.1.2.4.10Outgoing call / U3 MS originating call proceeding / lower layer failure去话/ U3 MS发话进行/较低层讯号失败26.8.1.2.4.11Outgoing call / U3 MS originating call proceeding / unknown message received去话/ U3 MS发话进行/未知讯息接收26.8.1.2.4.12Outgoing call / U3 MS origin

47、ating call proceeding / internal alerting indication去话/ U3 MS发话进行/内部警告指示26.8.1.2.4.13Outgoing call / U4 call delivered / CONNECT received去话/ U4通话传送/ CONNECT接收26.8.1.2.5.1Outgoing call / U4 call delivered / termination requested by user去话/ U4通话传送/用户通话请求结束26.8.1.2.5.2Outgoing call / U4 call delivered

48、/ DISCONNECT with in band tones去话/ U4通话传送/ DISCONNECT DISCONNECT接收,但具频带内音频26.8.1.2.5.3Outgoing call / U4 call delivered / DISCONNECT without in band tones去话/ U4通话传送/ DISCONNECT DISCONNECT接收,但无频带内音频26.8.1.2.5.4Outgoing call / U4 call delivered / RELEASE received去话/ U4通话传送/ RELEASE接收26.8.1.2.5.5Outgoi

49、ng call / U4 call delivered / lower layer failure去话/ U4通话传送/较低层讯号失败26.8.1.2.5.6Outgoing call / U4 call delivered / traffic channel allocation去话/ U4通话传送/话务频道指配26.8.1.2.5.7Outgoing call / U4 call delivered / unknown message received去话/ U4通话传送/未知讯息接收26.8.1.2.5.8U10 call active / termination requested b

50、y the userU10通话进行/用户通话请求结束26.8.1.2.6.1U10 call active / RELEASE receivedU10通话进行/ RELEASE接收26.8.1.2.6.2U10 call active / DISCONNECT with in band tonesU10通话进行/ DISCONNECT接收,但具频带内音频26.8.1.2.6.3U10 call active / DISCONNECT without in band tones U10通话进行/ DISCONNECT接收,但无频带内音频26.8.1.2.6.4U10 call active /

51、RELEASE COMPLETE receivedU10通话进行/ RELEASE COMPLETE接收26.8.1.2.6.5U10 call active / SETUP receivedU10通话进行/ SETUP接收26.8.1.2.6.6U11 disconnect request / clear collisionU11断线请求/清除冲突26.8.1.2.7.1U11 disconnect request / RELEASE receivedU11断线请求/ RELEASE接收26.8.1.2.7.2U11 disconnect request / timer T305 time-

52、out U11断线请求/定时器T305暂停26.8.1.2.6.3U11 disconnect request / lower layer failureU11断线请求/较低层讯号失败26.8.1.2.6.4U11 disconnect request / unknown message receivedU11断线请求/未知讯息接收26.8.1.2.7.5U12 disconnect indication / call releasing requested by the userU12断线请求/用户通话请求结束26.8.1.2.8.1U12 disconnect indication / R

53、ELEASE receivedU12断线请求/ RELEASE接收26.8.1.2.8.2U12 disconnect indication / lower layer failureU12断线请求/较低层讯号失败26.8.1.2.8.3U12 disconnect indication / unknown message received U12断线请求/未知讯息接收26.8.1.2.8.4Outgoing call / U19 release request / timer T308 time-out去话/ U19释出请求/定时器T308暂停26.8.1.2.9.1Outgoing cal

54、l / U19 release request / 2nd timer T308 time-out去话/ U19释出请求/第2定时器T308暂停26.8.1.2.9.2Outgoing call / U19 release request / RELEASE received去话/ U19释出请求/ RELEASE接收26.8.1.2.9.3Outgoing call / U19 release request / RELEASE COMPLETE received去话/ U19释出请求/ RELEASE COMPLETE接收26.8.1.2.9.4Outgoing call / U19 re

55、lease request / lower layer failure去话/ U19释出请求/较低层讯号失败26.8.1.2.9.5Incoming call / U0 null state / SETUP received with a non supported bearer capability来话/U0空态/ SETUP接收具非支持承载能力26.8.1.3.1.1Incoming call / U6 call present / automatic call rejection来话/U6通话出现/自动通话拒绝26.8.1.3.2.1Incoming call / U9 mobile t

56、erminating confirmed / alerting or immediate connecting来话/U9行动结束确认/警告或立即联机26.8.1.3.3.1Incoming call / U9 mobile terminating confirmed / TCH assignment来话/U9行动结束确认/TCH指配26.8.1.3.3.2Incoming call / U9 mobile terminating confirmed / termination requested by the user来话/U9行动结束确认/用户通话请求结束26.8.1.3.3.3Incomi

57、ng call / U9 mobile terminating confirmed / DISCONNECT received 来话/U9行动结束确认/ DISCONNECT接收26.8.1.3.3.4Incoming call / U9 mobile terminating confirmed / RELEASE received来话/U9行动结束确认/ RELEASE接收26.8.1.3.3.5Incoming call / U9 mobile terminating confirmed / lower layer failure来话/U9行动结束确认/较低层讯号失败26.8.1.3.3.

58、6Incoming call / U9 mobile terminating confirmed / unknown message received来话/U9行动结束确认/未知讯息接收26.8.1.3.3.7Incoming call / U7 call received / call accepted来话/U7行动结束确认/通话收到26.8.1.3.4.1Incoming call / U7 call received / termination requested by the user来话/U7通话收到/用户通话请求结束26.8.1.3.4.2Incoming call / U7 call received / DISCONNECT received来话/U7通话收到/ DISCONNECT接收26.8.1.3.4.3Incoming call / U7 call received / RELEASE received 来话/U7通话收到/ RELEASE接收26.8.1.3.4.4Incoming call / U7 call received / lower layer failure来话/U7通话收到/较低层讯号失败26.8.1.3.4.5

展开阅读全文
温馨提示:
1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 装配图网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

copyright@ 2023-2025  zhuangpeitu.com 装配图网版权所有   联系电话:18123376007

备案号:ICP2024067431-1 川公网安备51140202000466号


本站为文档C2C交易模式,即用户上传的文档直接被用户下载,本站只是中间服务平台,本站所有文档下载所得的收益归上传人(含作者)所有。装配图网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。若文档所含内容侵犯了您的版权或隐私,请立即通知装配图网,我们立即给予删除!