SSCNETTraining(光纤定位手册)

《SSCNETTraining(光纤定位手册)》由会员分享，可在线阅读，更多相关《SSCNETTraining(光纤定位手册)（24页珍藏版）》请在装配图网上搜索。

1、0+FX3U High Speed AdaptersTrainingFall 20061Brief Historyl FX3U-20SSC-Hl Designed to compete in the growing Positioning Control Market at the Micro&Compact PLC rangel Based on the Q-Series QD75MH-2 positioning module and adapted for the FX-SeriesnUsing MR-J3-B type MELSERVOnDedicated Software also b

2、ased on Q-seriesl Intended for High Speed,High Precision,simultaneous and interpolated multi-axis positioning control2Features Overviewl FX3U-20SSC-Hl 2-Axis Control per FX3U-20SSC-H unitl High Speed PositioningnUp to 50MHz Pulse Train Outputl High Precision Positioningn262,144 pulse/revolution Serv

3、o Resolutionl High Speed Responsen1.7ms Control Cycle per Commandl Parameter Data RetentionnUses both Flash Memory(ROM)and Buffer Memory3Features Overviewl SSCNET III Fiber Optic Cablingl High Speed Controln50Mbps Data Transmission Speedl Up to 50m Between Nodesn2-Axes;100m Total Network Extension p

4、er Unitl Noise Immunityl Easy Plug-and-Play Wiring4Features Overviewl MR-J3-B Servosl 262,144 pulse/revolution Resolutionl Up to 6000rpm Motor Speedl 900Hz Frequency Responsel As Low as 0.44ms Cycle Timel Ultra Compact Sizel Advanced Vibration Suppressionl Parameter RetentionnExternal Battery(option

5、al)l USB Direct PC AccessnMR Configurator Software(optional)5Advantages&Marketing Pointsl High Speed&Precision Positioningl High Speed Control&Responsel Parameter Data Retentionl Easy Setup using Dedicated Softwarel Noise Immunityl Reduced Wiringl Reduced System Sizel Complete Micro-PLC Positioning

6、Solution6Parameter Data Retentionl Buffer Memory vs.Flash Memory(ROM)7Parameter Data Retentionl Buffer Memory vs.Flash Memory(ROM)8Software:FX Configurator-FPl Dedicated FX3U-20SSC-H Setup Softwarel Launched from GX Developer or Independentlyl Easy Setup of FX3U-20SSC-H&Servo Parametersl Parameters

7、are loaded from Flash ROM BFM Amplifier automatically when power switches from OFF to ONnPositioning ParametersnServo ParametersnTable Datal Monitor the Module in Real-timel Test Module Commands/Functions910Software:FX Configurator-FPl Connection Setup11Software:FX Configurator-FPl Reading from the

8、Module12Software:FX Configurator-FPl Required Settingsl Positioning Parametersn0PR Moden1:Data Setn0PR Interlock Settingn0:Invalidl Servo ParametersnServo Amplifier Seriesn1:MR-J3-BnBasic Setting Parameters:Servo Forced Stop Selectionn1:Invalid(Do not use the forced stop signal)13Software:FX Configu

9、rator-FPl Writing to the Module14Software:FX Configurator-FPl Verifying Module Data15Software:FX Configurator-FPl Monitor Mode16Software:FX Configurator-FPl Test Mode17Software:FX Configurator-FPl Table Data18PLC Ladder Controll PLC Ladder can control all FX3U-20SSC-H functionsl Use FX3U high speed

10、TO/FROM commands to access modules Buffer Memory(BFM)nRefer to FX3U-20SSC-H Users Manual Appendix A for complete BFM Listl TO/FROM should be minimized to keep the PLC scan time as short as possiblenUsing Commands like Master Control(MC)and Call(CALL)are highly suggestedl Allows users to Create Custom GOT/PLC/20SSC-H Operation Interfaces1920PLC Ladder Controll Example GT1155 Interface21FX3U High Speed Adaptersl Example High Speed Adapter GT1155 Interface22Pong Demonstrationl Input Password and go to SSCNET Pong23