英文翻译---汽车—司机系统的研究处理 英文

上传人:红** 文档编号:171439801 上传时间:2022-11-26 格式:PDF 页数:6 大小:158.18KB
收藏 版权申诉 举报 下载
英文翻译---汽车—司机系统的研究处理 英文_第1页
第1页 / 共6页
英文翻译---汽车—司机系统的研究处理 英文_第2页
第2页 / 共6页
英文翻译---汽车—司机系统的研究处理 英文_第3页
第3页 / 共6页
资源描述:

《英文翻译---汽车—司机系统的研究处理 英文》由会员分享,可在线阅读,更多相关《英文翻译---汽车—司机系统的研究处理 英文(6页珍藏版)》请在装配图网上搜索。

1、 Handling Studies of Driver-Vehicle Systems M.Lin,A.A.Popov and S.McWilliam School of Mechanical,Materials,Manufacturing Engineering and Management,University of Nottingham,University Park,Nottingham NG7 2RD,U.K.Email:eaxmlnottingham.ac.uk The driver-vehicle system approach provides a firm basis for

2、 analysing vehicle and driver dynamics in vehicle handling design.The paper aims to provide an analysis of drivers steering and speed control during driver-vehicle interaction.Generic mathematical models of vehicle and driver are implemented,and the handling characteristics in typical manoeuvres are

3、 studied through numerical simulations.As information technology and electronic systems are widely introduced for vehicle chassis control nowadays,new human factor problems have been posed in the simulation for vehicle handling studies.The proposed models here provide tools for exploring the effects

4、 of active chassis intervention systems on the driver-vehicle.Keywords/driver-vehicle systems,vehicle dynamics,driver behaviour,chassis enhancement systems 1.INTRODUCTION Recently,as virtual prototyping has been increasingly applied in vehicle development,vehicle handling design in a virtual environ

5、ment has also been widely used in both academic research and the manufacturing area.For vehicle handling simulations,vehicle dynamics simulation models(VDSMs)are necessities for the developers.Since 1960s 35611,VDSMs have been developed for a variety of applications,including dynamic analysis,intera

6、ctive driving simulation,and vehicle testing.The model complexity and solution procedures are defined according to a given application.It can be seen that the vehicle and driver form a closely coupled man-machine system.The interaction between the dynamics of the vehicle and the driver behaviour pla

7、ys a paramount role throughout the whole process of the simulation.At the same time,due to the desire for personal mobility,automotive chassis enhancement systems are introduced into vehicles.They are targeting on providing safety,stability and comfort,and minimising the environmental impacts.Howeve

8、r,it is argued that in some cases these chassis enhancement systems can cause more harm than good.In 9,Sharp pointed out that the assessment of driver-vehicle dynamics qualities in the context of electronic enhanced vehicles contains many separate quality issues and many design conflicts.This involv

9、es driver-vehicle speed control and its relationship with directional/steering control,which has only recently received attention.A detailed review on automotive chassis enhancement systems in heavy vehicles,provided by Palkovics and Fries 8,includes systems such as anti-lock braking system(ABS),tra

10、ction control system(TCS),rear axle steering system and dynamic stability control system.It is suggested that the driver is kept in the control loop as drivers intention is necessary to activate the systems.By making a vehicle easier to control,drivers may be encouraged to drive closer to the vehicl

11、e limits,therefore affecting the intended safety benefits.In the following sections,a basic 4-DOF(longitudinal,lateral,yaw,roll)vehicle model and a driver control model are presented.The driver model is directionally structured to control vehicle heading/yaw angle and lateral position,and longitudin

12、ally perceiving the longitudinal acceleration error.In Section 4,driver-vehicle interaction is reviewed.The simulation is then employed in Section 5 to analyse manoeuvres involving double lane change and braking in turn.2.VEHICLE MODEL The vehicle is represented by a four degrees of freedom model 4,

13、for the longitudinal,lateral,yaw and roll motion.As shown in Fig.1,although the suspensions are not included in the modelling,the model uses a simplified description of body roll assuming a fixed roll axis defined by the heights of the roll centres of the front and rear axles of the vehicle.Vehicle

14、model parameters are reported in the Appendix.The equations of motion using axes fixed to the vehicle body are given by,sincos)(yfFxfFxrFrvum+=+?sincos)(xfFyfFyrFruvm+=+?)sincos(sin)sincos(yfFxfFxrFhyrFbxfFyfFapxzIrzI+=?)sincos(cos)(sin)()(xfyfyrzrzfrfrfxzxFFFhFFhpcckkrIpI+=+?(1)mgzyC.G.hrfruVvLC.G.

15、C.G.abFzrFyrFxfFxrFzfFxrFxfFyf,rhgxzyxFzf,rFyfroll axis Fig.1 Vehicle Model where Fxf,Fxr,Fyf,Fyr,and Fzf,Fzr are vehicle axle longitudinal,lateral and vertical forces,respectively.r is the yaw rate and p and are the roll rate and roll angle.The sideslip angles and static camber angles of the front

16、and rear wheels f,rand f,r can be defined in terms of vehicle motion variables,rrffrhuhprbvarhuhprava?+=?+=sincostansincostan (2)rrff=(3)When the vehicle is running at constant speed,the longitudinal motion can be uncoupled from the equations of motion.The dynamics of the non-linear vehicle model in

17、cludes the influence of the non-linear tyre characteristics,which are modelled by the magic formula 7.The effects of lateral and longitudinal load transfers have been evaluated through a steady state approximation 10.Assuming a fixed roll axis position,the expression of the lateral load transfer for

18、 the front and the rear axles are,)()(_hdLhhatmruFhdLhhbtmruFrgrlatrzfgflatfz+=+=(4)The longitudinal load transfer,occurring while the varied vehicle forward velocity is taken into account,is calculated as follows,LhFFFgFrfxlongz/)(_+=(5)3.DRIVER BEHAVIOUR THROUGH PATH PREVIEW Obviously,only the veh

19、icle itself cannot maintain a desired path.This demands a combination with driver model.The driver has visual and motion feedbacks for developing steering control actions.Driver behaviour through path preview involves actions based on perception of commands.For directional/steering control,drivers c

20、an use preview behaviour to follow curved paths.A vehicle will follow a curved path for a given steering angle,so the driver can match horizontal road curvature with appropriate steer angle,and the remaining lane displacement can be handled with compensatory control actions.For speed control,the dri

21、ver tries to match road grade with a throttle angle,although the correct perception of road grade is much more difficult and imprecise than the perception for horizontal curvature.3.1 Directional/Steering Control For drivers visual feedback,a two-level(preview and compensatory)driver steering model

22、based on the control strategy proposed by Donges 3 is presented here.The driver exerts steering control to maintain lane position through preview control,and to manoeuvre the vehicle during curve negotiation,lane change or obstacle avoidance.Unpredictable road disturbances can randomly move the vehi

23、cle within the lane,and the driver must counteract these disturbances with compensatory control.For preview control,Weir and McRuer 12 suggested that,systems structured to control vehicle heading/yaw angle and lateral position or path angle and lateral position offer good closed-loop characteristics

24、.Therefore,it is assumed here that the driver develops steering corrections based on perceived heading/yaw and lane position errors.By setting a preview point P on the vehicle-fixed x axis,a sort of predictive behaviour is incorporated into the system.Fig.2 illustrates drivers behaviour through path

25、 preview.A composite heading error of the preview point relative to the desired path at the preview point is given by,)(/PPecLy+=(6)where ye is the lane position error,LP is the preview distance,is the heading angle and P is the heading angle between x axis and AP line.Instead of separately perceivi

26、ng both heading and lane position errors,the driver needs only to perceive the angular error c to the preview point down the road.The preview distance LP here is the product of vehicle forward speed and preview time constant TP.This is consistent with our everyday experience that driver sees nearer

27、distance at lower speeds and further distance at higher speeds.Following McRuers crossover model 6,drivers compensatory feedback control can be defined by the transfer function of the steering angle to the composite heading error,sILcesTsTGss+=)11()()(7)It includes three components:a gain G which se

28、ts the magnitude of road steering angle corrections for given heading error c;a lead term)1(+sTLthat the driver adopts to counteract vehicle tyre delay;a lag term)1(+sTIcorresponding to the neuromuscular delay;and,a time delay se approximating drivers reaction time delay.For drivers motion feedback,

29、it provides information on motion performed by human organs and on orientation with respect to the gravitational direction.In 1,Allen noted that the yaw rate information can be used as a motion feedback element.The motion feedback gain Km provides a lead that the driver can use to compensate for the

30、 vehicle yaw rate lag.3.2 Speed Control Speed control is important in a variety of scenarios,including maintaining safe lateral acceleration levels while following curved paths,responding to speed limits,and slowing down during emergency avoidance.During straight running the driver continues at spec

31、ified speed.When the driver detects curvature,speed is then reduced accordingly in order to maintain desired lateral acceleration.The driver speed control law can then be described as Fig.3(a).The driver commands deceleration consistent with a desired speed change,and perceives deceleration errors.E

32、specially,when electronic chassis controls,such as ABS,TCS,etc.,are involved,speed control will be essential.As we can see from the operating principles of these control systems,most of them are activated under emergency situations.Speed changing is therefore inevitable.For example,by adding an effe

33、ctive ABS,the relationship between the brake pedal force and vehicle deceleration is illustrated in Fig.3(b).With the application of this relationship and the speed control law described above,the assessment of effects of these electronic controls is feasible.AcPreview point P PLP y x XYye/LP Desire

34、d pathP Fig.2 Driver Model through Path Preview Fig.3(b)Driver Speed Control Law (a)ABS System Characteristic 4.DRIVER-VEHICLE INTERACTION 4.1 Driver-Vehicle Dynamics without Speed Control Given the above dynamic characteristics for the vehicle and driver,a block diagram of the overall driver-vehicl

35、e system model without speed control can be structured as shown in Fig.4.It is assumed that the vehicle is travelling at constant forward speed.Vehicle lateral velocity v,yaw rate r and roll rate p are generated by steering inputs to the vehicle equations of motion.Vehicle lateral velocity v and yaw

36、 rate r are then under direct control of the driver.Although the roll motion is not controlled by the driver directly,it also influences driver behaviour,especially when the variation of vehicle forward velocity is taken into account.Kinematical equations then provide vehicle heading angle and later

37、al lane position from lateral velocity and yaw rate.Finally,steering corrections will be made by the driver based on the composite heading error.For the closed-loop analysis,there are two system inputs,one is the path command yc,and the other is the initial heading angle command P.The vehicle will b

38、e steered to follow path commands,and P will help implement the correction of visual error.However,with the application of the crossover model merely,a lateral deviation can be found in the simulation(Fig.5(a).It is assumed that the driver continues to steer until the vehicles attitude intersects th

39、e preview point down the road.This strategy finally eliminates vehicle attitude errors but does not correct lane position errors.Therefore,an additional feedback is needed that accumulates error whenever vehicle is not correctly positioned laterally in the lane.By adding a parallel integrator in the

40、 system,this offset error can be eliminated(Fig.5(b).The function of this integrator is to compensate for the composite heading error,which accumulates both the vehicle heading error and the lane position error(Fig.4).It develops much quicker compensation than having the integrator compensate for la

41、ne position error only.The transfer function of the steering angle to the composite heading error can then be defined as,)1()11()()(sKesTsTGsssILc+=(7)Fig.4 Driver-Vehicle System Directional Control Model Brake Pedal Force+_decelerationerrorWithout ABSWith ABSVehicle decelerationSpeedControlVehicleL

42、ongitudinalDynamicsbrakePedalforceactualdecelerationdecelerationcommand(b)(a)(a)without integrator (b)with integrator Fig.5 Effect of the Parallel Integrator 4.2 Driver-Vehicle Dynamics with Speed Control When speed control is concerned,driver-vehicle interaction is the result of drivers longitudina

43、l and lateral controls,which reflects the driver control behaviour in a more tactical level.Fig.6 represents the structure of the interaction.The upper part of Fig.6 describes the driver directional control behaviour,and the lower part describes the speed control behaviour.By looking at the path inf

44、ormation and feedback of vehicle responses,the relationship between them can be processed.Fig.6 Driver-Vehicle Interaction with Speed Control 5.PERFORMANCE ANALYSIS 5.1 Double Lane Change at a Constant Speed Driver-vehicle model without speed control is applied here for a double lane change manoeuvr

45、e.Refer to the Appendix for vehicle parameters.Fig.7 shows the system responses.It can be seen that path information inputs make possible the analysis of the vehicles performances.The driver steers along a standard ISO double lane change manoeuvre with the constant forward speed 80km/h,and tracks th

46、e desired path using the two-level control.Therefore,drivers steering input is determined by the motion of the desired path to be followed by the preview point through the coupling of the preview distance LP,and also by drivers behaviour of the inverse dynamics of the vehicle.As shown in Fig.7(a),th

47、e manoeuvre requires the vehicle to travel for 15m in the original lane,to change lane with a lateral displacement of 3.5m in 30m,to stay in this lane for 25m and to return to the original lane in 25m.The driver successfully performed the required manoeuvre without touching the cones delimiting the

48、lanes.The action of the driver is with a short delay,and with a small gain,not to induce instability.The other results show the characteristic W shape of the double lane change responses.The system responds with a peak road steering wheel angle 1.6(Fig.7(b),which results in peak lateral acceleration

49、s of about 0.4g(Fig.7(c).This value is above average drivers preference 2.It stems from the tyre saturation near the peak value.The oscillations are characterised by the natural frequency and damping of the model.(a)cones(b)(c)Fig.7 Transient Response in Double Lane Change Constant Speed V=80km/h (D

50、river parameters:G=0.35,=0.1s,TL=0.1s,TI=0.2s,K=0.05,Km=0.01,TP=1s)5.2 Braking in Turn Scenario Now consider the combined steering and speed control driver-vehicle model for the braking in turn manoeuvre.Fig.8 illustrates the characteristic responses of the model.The driver enters a 300m-radius turn

51、 with a speed of 100km/h.Since the turn is sharper than expected,the manoeuvre results in excessive lateral acceleration ay,about 0.3g in Fig.8.Statistically 2,a cautious driver applies low to moderate deceleration while driving,with the result of reducing ay below 0.26g.The driver model is therefor

52、e set up to reduce ay to some percentage below 0.26g,corresponding with a reduced speed at around 88km/h.The speed control law is previously described in section 3.2,and the command braking deceleration is set at 0.2gs.One should note that when the lateral acceleration exceeds 0.3gs(Fig.8(b),the dri

53、ver model begins braking,which is subsequently brought up to the longitudinal command level of 0.2gs(Fig.8(a).The vehicle goes into oversteer as evidenced by the actual trajectory crossing the desired during the braking process(Fig.8(c).This is a result of a reduction in the rear axle+_ Steering Whe

54、el Angle+_ path command Speed Control Vehicle Longitudinal Dynamics brake Pedal forceactual decelerationdeceleration command Directional/Steering Control Vehicle Lateral Dynamics path information actual path cornering stiffness.The driver is then able to reduce speed and bring the vehicle back under

55、 stable control in understeer condition after the vehicle reaches the desired speed,as evidenced in the steady state of lateral acceleration.(a)(b)(c)Fig.8 Driver-Vehicle Response in Braking in Turn 6.CONCLUSIONS AND FURTHER RESEARCH Rational driver directional/steering and speed control models have

56、 been specified based on vehicle attitude,lateral position and longitudinal deceleration controls.Driver-vehicle system performances in double lane change and braking in turn scenarios are studied.The analysis has demonstrated stable control of the system simulation.Steering control stability has be

57、en achieved with preview-compensatory model over a speed range.The proposed models in the paper are aimed at the assessment of effects of electronic chassis enhancement systems.They provide tools for the exploration of the effects of active chassis intervention systems on the driver-vehicle interact

58、ion in future research.REFERENCES 1 Allen R.W.,Analysis and Computer Simulation of Driver/Vehicle Interaction,SAE Transactions,871086 2 Allen R.W.,Rosenthal T.J.,and Szostak H.T.,Steady State and Transient Analysis of Ground Vehicle Handling,SAE Paper No.870495,Feb.1987 3 Donges E.,A two-level model

59、 of driver steering behaviour,Human factors,1978,20(6),pp.691-707 4 Ellis J.R.,Vehicle Handling Dynamics,Mechanical Engineering Publication Limited,London,1994 5 Kondo M.et al.,Drivers Sight Point and Dynamics of Driver/Vehicle System Related to It,SAE paper 680104,1968 6 McRuer D.T.,Allen R.W.,Weir

60、 D.H.and Klein R.H.,New Results in Driver Steering Control Models,Human Factors,19(4),1977,pp.381-397 7 Pacejka H.B.and Bakker E.,The Magic Formula Tyre Model,Vehicle System Dynamics,vol.20(1991),pp.1-17 8 Palkovics L.and Fries A.,Intelligent Electronic Systems in Commercial Vehicles for Enhanced Tr

61、affic Safety,Vehicle System Dynamics,35(2001),No.4-5,pp.227-289 9 Sharp R.S.,Some Contemporary Problems in Road Vehicle Dynamics,Proc.of Instn.Mech.Engrs.,Vol.214,1999,pp.137-148 10 Sharp R.S.,Casanova D.and Symonds P.,A Mathematical Model for Driver Steering Control,with Design,Tuning and Performan

62、ce Results,Vehicle System Dynamics,33(2000),pp.289-326 11 Sheridan T.B.,Vehicle Handling:Mathematical Characteristics of the Driver,SAE paper 638B,Jan.1963 12 Weir D.H.and McRuer D.T.,Dynamics of Driver Vehicle Steering Control,Automatica,Vol.6,1970,pp.87-98 APPENDIX Vehicle Model Parameters Vehicle

63、 mass m=830 kg Vehicle yaw moment of inertia Iz=1210 kgm2 Vehicle roll moment of inertia Ix=290 kgm2 Product of inertia Ixz=-84 kg m2 C.G.height hg=0.53 m Distance of C.G.from the roll axis h=0.4 m Wheel base L=2.16 m Distance of C.G.from the front axle a=0.87 m Distance of C.G.from the rear axle b=

64、1.29 m Front wheel track tf=1.284 m Rear wheel track t=1.277 m Front axle roll stiffness fk=29860 Nm/rad Rear axle roll stiffness rk=19260 Nm/rad Front axle roll damping coefficient fc=2000 Nms/rad Rear axle roll damping coefficient rc=1860 Nms/rad Front axle roll steer coefficient f=-0.08 Rear axle

65、 roll steer coefficient r=0.12 Front axle roll camber coefficient f=0.60 Rear axle roll camber coefficient r=0.90 Front axle roll stiffness proportion fd=60.79%Rear axle roll stiffness proportion rd=39.21%Magic Formula Coefficients Lateral force:a0=1.6929,a1=-55.2084,a2=1271.2800,a3=1601.8000,a4=6.4946,a5=4.7966e-3,a6=-0.3875,a7=1.0000,a8=a9=a10=a111=a112=a12=a13=0 Longitudinal force:b0=1.6500,b1=-7.6118,b2=1122.6,b3=-7.3600e-3,b4=144.8200,b5=-7.6614e-2,b6=-3.8600e-3,b7=8.5055e-2,b8=7.5719e-2,b9=2.3655e-2,b10=2.3655e-2

展开阅读全文
温馨提示:
1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 装配图网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

copyright@ 2023-2025  zhuangpeitu.com 装配图网版权所有   联系电话:18123376007

备案号:ICP2024067431-1 川公网安备51140202000466号


本站为文档C2C交易模式,即用户上传的文档直接被用户下载,本站只是中间服务平台,本站所有文档下载所得的收益归上传人(含作者)所有。装配图网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。若文档所含内容侵犯了您的版权或隐私,请立即通知装配图网,我们立即给予删除!