解读桥式起重机运行机构的驱动方式

《解读桥式起重机运行机构的驱动方式》由会员分享，可在线阅读，更多相关《解读桥式起重机运行机构的驱动方式（3页珍藏版）》请在装配图网上搜索。

1、解读桥式起重机运行机构的驱动方式Interpretation of the bridge crane operation way of driving起重量是起重机安全工作所允许起吊的最大质量，称为额定起重量，单位为kg或t表示， 是衡量起重机工作能力的一个重要参数。起重量不包括吊钩、动滑轮组及钢丝绳等基本吊具 的重量，但抓斗、起重电磁铁等吊具的重量包括在内。Lifting weight is allowed by the lifting crane safety work of the largest mass, known as the rated lifting weight, the

2、unit is kg or t says, is an important measure of crane working ability. Lifting weight does not include the hook, movable pulley and steel wire rope sling basic set of weight, but the weight of the grab, lifting electromagnet spreader is included.起重量较大的起重机一般都有两个起升机构，起重能力大的叫主起升机构，俗称主钩。起重 量较小的是副起升机构，俗

3、称副钩。副钩的起升速度大于主钩，这样可以提高装卸轻货的工 作效率。主副钩的起重量用分数形式表示，例如205，分子表示主钩起重量为 20 吨，分 母表示副钩起重量为 5 吨。The weight of the larger crane usually have two lifting mechanism, lifting capacity big main lifting mechanism, commonly known as the main hook. Is a pair of hoisting mechanism of lifting weight smaller, commonly k

4、nown as vice hook. Vice hook lifting speed is greater than the main hook, so can improve the work efficiency of light loading and unloading cargo. Main hook up the weight in the form of a fraction, 20/5, for example, molecular said the main hook load of 20 tons, the denominator said vice hook load i

5、s 5 tons.工作类型也称工作制度，是表明起重机工作繁重程度的参数，它关系到起重机金属结构、机 构的零部件、电动机和电气设备的选型，主要体现在繁忙程度和载荷变化程度两个方面。Type of work is also called the working system, it is showed that the crane work hard degree of parameters, it relates to the crane metal structure, components, motor and electrical equipment selection, mainly r

6、eflected in the busy degree and degree of load change two aspects. 工作繁忙程度。对起重机整体来说，就是指一年时间内，起重机实际运转时数与总时数之比。 对机构来说，则是指某一机构在一年时间内运转时数与总时数之比。在起重机的一个工作循 环中，机构运转时间所占的百分比，称为该机构的负载持续率，用汉语拼音的两个字母 JC 表示。Job is busy. The crane as a whole, is refers to one year time, crane the ratio of the actual working hour

7、s and hours. For institutions, is a particular institution running hours in a year time and the ratio of the total hours. In one work cycle crane, the percentage of working time, called the duty cycle of the agency, expressed in the two Chinese phonetic alphabet JC %.载荷变化程度。按额定起重量设计的门、桥式起重机实际作业中，起重机

8、所起吊的载荷往往 小于额定起重量，这种载荷的变化程度用起重量利用系数K = Q均/Q额表示。Q均一一起 重机在全年实际起重量的平均值，Q额一一起重机的额定起重量。根据门、桥式起重机的工作繁忙程度和载荷变化程度，把起重机的工作类型划分为：轻级、中级、重级和特重级 四种级别。Load changes. The door is designed according to the rated lifting weight, bridge crane in practical operation, the crane load is often less than the rated lifting w

9、eight, lifting by the degree of the change of the load with lifting weight utilization coefficient K = Q/Q forehead said. Q- all crane in the average of the actual weight for the whole year, Q - crane rated lifting weight. According to the door, the degree of bridge crane busy work and load changes,

10、 the crane work types are divided into: light level, intermediate level, heavy and heavy four levels. 桥式重起机的种类很多，按其主梁的数量，可分为单梁和双梁两大类。 桥式通用起重机 是最常见的一类起重机。它的用途广泛适用于一般性的吊运工作。Many different kinds of bridge type reboot the machine, according to the number of the main girder, can be divided into two types

11、: single and double beam. Gm bridge crane is the most common type of crane. It is widely used in general lifting work. 桥式起重机是桥架在高架轨道上运行的一种桥架型起重机，又称天车。桥式起重机的桥架沿 铺设在两侧高架上的轨道纵向运行，起重小车沿铺设在桥架上的轨道横向运行，构成一矩形 的工作范围，就可以充分利用桥架下面的空间吊运物料，不受地面设备的阻碍。Bridge crane is a bridge in high orbit a bridge type crane, also

12、 known as the crown. Bridge crane bridge along the laid on on both sides of the elevated rail longitudinal operation, lifting trolley along the bridge is laid on the orbits of the horizontal run, a rectangular scope of work, can make full use of bridge the space below the lifting materials, from the

13、 ground equipment obstacles. 桥式起重机广泛地应用在室内外仓库、厂房、码头和露天贮料场等处。桥式起重机可分为普 通桥式起重机、简易粱桥式起重机和冶金专用桥式起重机三种。Bridge crane is widely used in indoor and outdoor warehouses, factories, docks and outdoor storage yard, etc. Bridge crane can be divided into general bridge crane, simple beam bridge crane and metallur

14、gical special bridge crane 3 kinds. 普通桥式起重机一般由起重小车、桥架运行机构、桥架金属结构组成。起重小车又由起升机 构、小车运行机构和小车架三部分组成。General bridge crane by lifting the car, general bridge operation, the structure of the bridge metal composition. Lifting trolley and running institutions by the lifting mechanism, the car and the car fram

15、e of three parts. 起升机构包括电动机、制动器、减速器、卷筒和滑轮组。电动机通过减速器，带动卷筒转动， 使钢丝绳绕上卷筒或从卷筒放下，以升降重物。小车架是支托和安装起升机构和小车运行机 构等部件的机架，通常为焊接结构。Lifting mechanism including motor, brake, reducer, drum and pulley. Motor through the gear reducer, drive the drum rotation, make wound reel or wire rope from the reel down, in order

16、to lift heavy things. The car frame is bracket and install the lifting mechanism and the car running parts, such as organization frame, usually in the form of welding structure. 起重机运行机构的驱动方式可分为两大类：一类为集中驱动，即用一台电动机带动长传动轴 驱动两边的主动车轮；另一类为分别驱动、即两边的主动车轮各用一台电动机驱动。中、小 型桥式起重机较多采用制动器、减速器和电动机组合成一体的“三合一”驱动方式，大起重

17、 量的普通桥式起重机为便于安装和调整，驱动装置常采用万向联轴器。Crane operation of drive mode can be divided into two broad categories: type of concentrated drive, which USES an electric motor to drive the active wheels on both sides of the long shaft drive; Another kind of drive, which respectively on both sides of the active whe

18、el is driven by an electric motor. More medium and small bridge crane brake, reducer and motor group synthesis drive mode, the integration of the triad big lifting weight of ordinary bridge crane for ease of installation and adjustment, drive often adopt universal coupling. 桥架的金属结构由主粱和端粱组成，分为单主粱桥架和双

19、粱桥架两类。单主粱桥架由单根主 粱和位于跨度两边的端粱组成电缆设备，双粱桥架由两根主粱和端粱组成。Metal structure of the bridge is composed of main beams and the beams, divided into the single main beam bridge and double beam bridge. Single main beams bridge by a single main beams and the span of the end on both sides of the beam, double beam brid

20、ge is composed of two main beams and the beams. 主粱与端粱刚性连接，端粱两端装有车轮，用以支承桥架在高架上运行。主粱上焊有轨道， 供起重小车运行。桥式起重机桥架主粱的结构类型较多比较典型的有箱形结构、四桁架结构 和空腹桁架结构。Main beams and the beams rigid connection, equipped with wheels on both ends of the side beams, used to support bridge run on overhead. Welding on the main beam o

21、rbit, for lifting the car running. The type of bridge main beam structure is more typically have a box structure, four truss structure and vierendeel truss structure. 箱形结构又可分为正轨箱形双粱、偏轨箱形双粱、偏轨箱形单主粱等几种。正轨箱形双粱是 广泛采用的一种基本形式，主粱由上、下翼缘板和两侧的垂直腹板组成，小车钢轨布置在上 翼缘板的中心线上，它的结构简单，制造方便，适于成批生产，但自重较大。Box structure and

22、 can be divided into the right box box double double liang, partial rail beams, partial rail box single main beams, etc. On track box double liang is a basic form of widely used, the main beam by on either side of the upper and lower flange plate and the vertical web, rail car arrangement in the center of the line on the flange, its simple structure, easy fabrication, suitable for batch production, but gravity is bigger. 偏轨箱形双粱和偏轨箱形单主粱的截面都是由上、下翼缘板和不等厚的主副腹板组成，小车 钢轨布置在主腹板上方，箱体内的短加劲板可以省去，其中偏轨箱形单主粱是由一根宽翼缘 箱形主粱代替两根主粱，自重较小，但制造较复杂。