交换机基础实训报告格式
《交换机基础实训报告格式》由会员分享,可在线阅读,更多相关《交换机基础实训报告格式(8页珍藏版)》请在装配图网上搜索。
1、交换机基础实训报告姓名: 学号: 专业:计算机网络技术 班级:10网络 指导教师: 朱家全 实训名称帧中继的配置指导教师朱家全实训目的熟悉和掌握帧中继协议的配置方法实训报告一、实验拓扑二、实验步骤1、连线根据拓扑完成所有设备的连接。2、配置准备工作:首先进入超级终端,设置各项参数(1)将路由器R2模拟成帧中继的交换机RouterRouterenRouter#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname FRFR(config)#frame-relay switc
2、hingFR(config)#interface serial 0/1/0FR(config-if)#encapsulation frame-relay ? MFR Multilink Frame Relay bundle interface ietf Use RFC1490/RFC2427 encapsulation FR(config-if)#encapsulation frame-relayFR(config-if)#frame-relay lmi-type ? cisco ansi q933aFR(config-if)#frame-relay lmi-type ciscoFR(conf
3、ig-if)#frame-relay intf-type ? dce Configure a FR DCE dte Configure a FR DTE nni Configure a FR NNIFR(config-if)#frame-relay intf-type dceFR(config-if)#clock rate 64000FR(config-if)#no shutdown按照同样的办法,完成其他接口的配置FR(config-if)#exitFR(config)#interface serial 0/3/0FR(config-if)#encapsulation frame-relay
4、FR(config-if)#frame-relay lmi-type ciscoFR(config-if)#frame-relay intf-type dceFR(config-if)#clock rate 64000FR(config-if)#no shutdownFR(config-if)#exitFR(config)#endFR#wr配置路由:FR(config)#interface serial 0/1/0FR(config-if)#frame-relay route 204 interface serial 0/3/0 402FR(config-if)#exitFR(config)#
5、interface serial 0/3/0FR(config-if)#frame-relay route 402 interface serial 0/1/0 204FR(config-if)#endFR#wr(2)配置路由器R1RouterRouterenRouter#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname R1R1(config)#interface serial 0/3/0R1(config-if)#encapsulation frame-rela
6、yR1(config-if)#no shutdown(3)配置路由器R3RouterRouterenRouter#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname R3R3 (config)#interface serial 0/3/0R3 (config-if)#ip address 172.168.1.3R3 (config-if)#encapsulation frame-relayR3 (config-if)#no shutdown(4)配置路由器R4RouterRouterenRouter#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname R4R4 (config)#interface serial 0/3/0R4 (config-if)#ip address 172.168.1.4R4 (config-if)#encapsulation frame-relayR4 (config-if)#no shutdown3、调试三、实验结果备注得分实训名称指导教师实训目的实训报告一、实验拓扑二、实验步骤三、实验结果备注得分
- 温馨提示:
1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 装配图网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。