玩具英语大全

《玩具英语大全》由会员分享，可在线阅读，更多相关《玩具英语大全（15页珍藏版）》请在装配图网上搜索。

1、玩具英语大全Reversible .riv:sbl 可反转的; 可逆的; 可掉换的; 可废弃的;双面可用的Manual. .mnjul 手工的体力的手册,2.便览,简介.例:You should read the manual before you turn on the new machine.在开这台新机器前,应该阅读使用手册。Rechargeable1. (蓄电池) 可再充电catapult: 发射机;发射playset水上基地?枪套 holsterfastener扣位眼罩goggleSheath剑鞘projectile飞弹Backpack to rear torso背包projecti

2、le飞弹kinetic energy动能Grappling hook爪钩Quality specification规格Plug2. 插头, 插塞Just put the plug in the socket and switch on the machine.只需将插头插入插座并开动机器就行了。die casting合金general metalworking shop基本五金加工厂rooting machine搪胶机器 rotocasting 搪胶工艺sewing machine车缝silk screen printing丝印tampo printing移印ultrasonic weldin

3、g超声焊接wooding processing 木工加工工序flat belt assembly流水线cadmium镉mercury汞震箱的顺序：正面 背面 侧面相对侧面 顶面 底面产品投掷投掷顺序和位置：盒底顺时针转90度再到第二面 顶部 转到第二面的对应一面包装盒两头与盒口相对应的一面 含盒口的一面 三边相交角从相交的角向外最短一边 从相交的角向外最长的一边。Part name 零件名称Main body 面壳Back cover底座turning table转盘ring固定圈button(L)大按制gear boxs cover牙箱盖Gear boxs base牙箱底wheel hold

4、er压件screw nut cover螺母介子 clutch极力子center gear转盘齿轮rollers横滚轮dart飞标Outer carton外箱Inner carton内箱inner card箱内咭circle label圆形贴纸top inner card上内咭bottom inner card下内咭top label 上贴纸bottom label 下贴纸tissue paper拷贝纸PE bag 胶袋clear tape透明胶纸packing wire包胶铁线shaft 2.5X 18mm搓花铁轴shaft bush 铜套Spring 弹弓Iron plate铁板magnet

5、 磁石Gear B齿轮Bgear oil 齿轮油PVC washer PVC介子Battery contact (+) 正极片防盗条(guard-against-theft label)? PCBA+3CAP+2INDUCTOR 电子板 inductor?Motor FN马达On/off switch开关lead free soldering wire无铅锡线无铅锡膏(no lead and tin paste)有危险性critical - 玩具英语第二部分内罩厚薄不均匀 uneven thickness of inner blister 用错内罩wrong inner blister内卡/托

6、座破裂 insert card/ platform cracked内卡/托座压坏 insert card/ platform crushed内卡/托座破烂insert card/ platform damaged 托座变形platform deformed玻璃纸擦花 abrasion mark on window sheet玻璃纸太多硅油 excessive silicon oil on window sheet摺线位破裂 folding line cracked 盖口打开 flap opened坐椅放歪interior mislocated 坐椅走位interior dislocated坐椅

7、松 interior loosed 坐椅走料不足 interior undershot窗放歪windshield dislocated 窗走位 windshield dislocated窗松windshield loosed 窗走料不足 windshield undershot窗裂 windshield cracked车轮不能转动 wheel does not rotate车轮不着地 one wheel does not land 甩车辘 wheel came off车辘连车轴放得不正确 barbell mislocated 车轮连轴放歪barbel dislocated车轮卡住车底与车身之间

8、 wheel jammed between wheel and chassis车轴太长heel axle length too long 生产来源地 country of oringin公司麦头 logo 包装方法package method 混装比例 packing ratio箱麦 shipping mark 颜色不配合 color mismatched污渍 dirty 生锈rust 烂broken 脱落came off变形deformed 走位dislocated 放得不正确mislocated漏产地来源missing country of origin 产地来源不清 country of

9、 origin illegible漏麦头missing logo 麦头不清楚 logo illegible包装方法错 incorrect packing method 错包装比例 incorrect packing ratio颜色不配合于color mismatched between污渍在dirt on 生锈在rust on 擦花痕在abrasion mark on刮花痕在scratched mark on工程常用英文tool plan模具表 part list零件表 wet paint list油漆表new project development新产品发展product content产品

10、资料 current products review已在生产线上之产品复核model手板 hard copy 复硬表 tooling model 供造模之手板tooling cost模价 tooling lead time 造模所须时间mold工模 die casting mold 合金压铸模plastic injection mold 塑胶模 tool drawing制模图product specification 成品规格 part drawing 零件图 model review手板复核model modification 手板修改 mold release 手板放产 tooling s

11、tart 开始造模tooling cast倒胶分型 mold base 模胚 core凸模 cavity 凹模ejector pin 顶针 guide pin 道针 return pin 回针 slide 行位spure 浇口 spreader 分流锥 gate 入水夹模book mask 边模plate mask 烫金 hot stamping fixture夹具超声波熔接sonic welding 冷打头cold heading热烫heat stick 粘合glue 热熔胶hot melt glue 吸塑罩blister发泡胶expanded ploy styrene 彩盒color bo

12、x 说明书instruction sheet吸塑咭blister card 内盒inner box 内箱inner carton邮包盒mail order box 外箱master carton box日期date code 胶纸tape 箱唛shipping mark胶袋 poly bag 泡泡袋bubble wrap bag 介子 washer 车轴axle锅钉rivet 紧压配合 press fit 滑配合 slide fit招纸decal 流道runner 垃圾位over flow 排气坑air vent雕刻engraving 火花机 (EDM)electro discharge ma

13、chine 打磨 fitting抛光polishing 工模进展情况 tool status第一次试模 1st shot第一次试模件 1st shot parts第一次啤件修改资料1st shot write up第二次试模2nd shot第二次试件2nd shot sample第三次试模3rd shot运输试验办 transit sample 掷箱试验 carton drop 拉力试验 pull test总装final assembly 落货 shipment啤塑molding 压铸die casting 涂水口 degating冲披锋 trimming 震机（用石仔打光） tumbling

14、 锁孔 drill hole 手喷 hand spray静电喷油 electrostatic (静电的)spraying 手喷模 spray masksDolls 娃娃electronic toys 电动玩具Outdoor leisure 户外娱乐Handicrafts 手工艺品 intelligence toys 益智玩具 fancy toy 益智玩具staff toys 毛绒玩具soft toys 软体类玩具stuffed toy 填充玩具Capsule Toys 扭蛋Shokugan 食玩Action Figure 可动人形Designer Toys 潮流玩具vinyl Toy 搪胶玩具

15、Brick 积木人garage kits 首版-玩具英语第三部分:Upper torso LT.of Skipper左上身Upper torso RT.of Skipper右上身Middle torso LT.of Skipper左中身Middle torso RT.of Skipper右中身Lower torso LT.of Skipper左下身Lower torso RT.of Skipper右下身Head of Skipper頭Shoulder LT. of Skipper左肩Shoulder RT. of Skipper右肩Upper arm LT. of Skipper左上臂Uppe

16、r arm RT. of Skipper右上臂Elbow LT. of Skipper左手肘Elbow RT. of Skipper右手肘Lower arm LT. of Skipper左下臂Lower arm RT. of Skipper右下臂Hand LT. of Skipper左手LT. upper leg up of Skipper左上腿上RT. upper leg up of Skipper右上腿上LT. upper leg low of Skipper左上腿下RT. upper leg low of Skipper右上腿下LT. knee of Skipper左膝RT. Knee

17、of Skipper右膝LT. lower leg up of Skipper左下腿上RT. lower leg up of Skipper右下腿上LT. lower leg low of Skipper左下腿下RT. lower leg low of Skipper右下腿下LT. foot of Skipper左腳RT. foot of Skipper右腳LT. toe of Skipper左腳趾RT. toe of Skipper右腳趾LT. sole cover of Skipper左鞋底盖RT. sole cover of Skipper右鞋底盖Vest of Skipper长袍Nec

18、klace of Skipper项链Neck joints of Skipper頸较Arm joints of Skipper手臂较Upper arm rivets of Skipper上臂釘Lower arm rivets of Skipper下臂釘Hand rivets of Skipper手釘leg joints of Skipper腿较Upper leg rivets of Skipper上腿釘Lower leg rivets of Skipper下腿釘Foot joints of Skipper腳较Foot rivets of Skipper腳釘Toe rivets of Skipp

19、er脚趾钉Upper waist joints of Skipper上腰接件Lower waist joints of Skipper下腰接件Ladder LT. 左梯Ladder RT.右梯ladder hinge梯鉸鏈Sound Module发声盒Submit 提交 服从 顺从 specify指定 详细说明列入清单Blow molding吹气模国家名称：哥斯达黎加Costa Rica 立陶宛Lithuania 捷克Czech 厄瓜多尔Ecuador危地马拉Guatemala 塞浦路斯 Cyprusreference sample 基准样品（标准样品） comment注释 评论 意见pain

20、t master 油色办Propeller螺旋桨Helicopter bottom 机底Handle housing LT 手摯左Handle cover LT 手柄片左Ripcord 拉条Ripcord handle left 拉条手柄左Gear牙仔Bush 套筒Body机身2-ply (厚度, 板层, 褶) corrugated carton sealed with 2.5-3tape at H shape双坑纸箱，用2.5-3” 胶纸封箱呈H形状Bar code must be printed on the master carton卡通箱必须印上条形码（bar code）Master

21、carton must be complied with ToyBiz or PO mentioned requirement卡通箱必须遵照ToyBiz 或 PO规定的要求package marking 包装标记location-on back panel背面Name and address of the supplier as defined by ASTM F963-96a Section 7供应商的名称和地址按ASTM F963 96a 第七章Statement of conformity i.e. “meet or exceed all safety requirements of t

22、he product safety code ASTM F963”正确性说明：产品安全性代码符合或超出安全条例ASTM F 963-96acorrect UPC code as below; 正确的通用UPC代码location on main panel 正面Warning statement in accordance with ASTM final rule警告性说明按ASTM F963-96a最终规则age grading : age 6&up 年龄等级 ：6岁及以上individual packing 独立包装each product is packed as blister 吸塑包

23、装12pieces per master carton 每个卡通箱装12pcsRemark: this assortment ration is in product development stage for reference. The detailed assortment ration must be referred to PO mentioned.备注；分类比率应参考产品发展进程。详细分类情况应查询PO之说明。Sample plan 抽样规则Product sampling 产品抽样The quantity of inspection samples should be selec

24、ted according to the sampling plan-MIL STD 105E,single sampling. level II检验样品必须按照规则-MIL-STD-105E从每个箱中抽取单式抽样级别II。Critical/safety AQL=0 极严重/安全性Major 严重AQL=1.5Minor轻微Aesthetic requirements 外观要求The open tray boxed must not be unsealed, scratched, wrinkled and damaged彩盒不能变形皱或破损The product must be packed

25、in an assigned orientation as per the signed sample.产品必须根据签板包装。There must not be any scratch, foreign pain, flow mark on the product and package that is seen clearly at a distance 20 away from the product.在距离产品20的地方查看产品和包装不能有擦花，变形，缩水。Evaluate the colors, styles and sizes of the product must be match

26、ed per signed sample. 颜色，款式和规格必须与签板符合。Unintentional gaps and seam mismatches between factory-assembly parts must not exceed 0.010 note: this does not include necessary clearance between moving parts装配部件非人为间隙不超过0.010注意：不包括活动部位必要的空隙。The gap between moving parts should be mot exceeding 0.025 inch.操作部件的

27、间隙不能超过0.025英寸。Functional requirements 功能要求General一般The product and its accessories can hold intended position during functional testing and in normal use mold, before or aging test.老化前后产品必须持位All accessories (except for spider man) must stand upright on a flat surface.必须能够直立于平台The exposed magnet on s

28、pider man s hand shouldnt exceeding 1.5mm, and should withstand the weight a minimum of 450g when hand stick the weight vertically.蜘蛛侠手上的磁石露出部分不能超过1.5毫米，能在垂直方向粘起至少450克的砝码。Evaluating coating on product per approval standard for coverage, color and position.产品颜色，颜色位置参照签办。Accessory assembly force must

29、not exceed the values below产品装拆力度不能超过以下值A 8lbs to attach/detach the accessories 装拆活动配件的力度为8B 2lbs to attach/detach umbrella (72414)装拆伞的力度为C 2lbs to attach/detach web trap (72412)All labels must be in their intended position without lifted edges or blister areas.贴纸须在指定的位置且不能有翘起，起泡现象。product must can

30、perform as below function:产品必须有以下功能Classification of defects缺陷分析Critical/safety classification 极严重/安全性分类Any accessible sharp points or sharp edges as defined in ASTM任何配件的尖点或利边参阅ASTM。Any dead or alive insect attached to the inside of the packages or the product,任何死亡或活的昆虫俯在包装内或产品上面Any stain on the pro

31、duct incurred by human or insect任何人或昆虫导致的污迹残留在产品上Any cutlery left in the package or product任何遗留在包装或产品内的刀具Any projectiles must not be small parts as record or /and after abuse任何射弹不准许滥用Any metal/plastic fasten has a sharp point is not allowed任何金属/塑料不允许有尖点All rigid projectiles shall have a tip radius o

32、f not less than 2mm.所有刚性射弹物不能有半径小于2毫米的尖头。The launcher mustnt discharge projectiles other than those provide with the toy.(ball pen, pencil cobblestone, needle, marble, correction pen.ect.) 发射器不能发射子弹以外的物体如圆珠笔铅笔圆石针校正笔等Functional defective classification功能缺陷分类Aesthetically defective classification外观缺陷分

33、类Please refer to appendix A of this specification请参照附录A外观检验规格Product drop test产品跌落试验Safety安全性Frequency: every shipment inspection周期：每批装运检验Sample size: 5 pieces each type; accept 0 defect抽样数每款5pcs;可接受0缺陷Method: 36.5inchesx4times 方法 36.5英寸x4次Failure: any findings violate ASTM F963-96a失败所有违反ASTM F 963-

34、96a 之结果Reliability 可靠性Frequency every shipment inspection周期：每批装运检验Sample size 5 pieces each type; accept 0 defect抽样数 每款5pcs;可接受0缺陷Method 30inchesx4times 方法 30英寸x4次Failure: any finding violate ASTM F963-96a or breakage or functional failure as defined in section 4.0 任何违反ASTM F963-96a 或损害或如4.0节中定义的功能失

35、败Torque and tension tests扭力/拉力试验Safety安全性Frequency: every shipment inspection周期：每批装运检验Sample size: 5 pieces each type; accept 0 defect抽样数每款5pcs;可接受0缺陷Component test: all graspable parts which safety hazard may be revealed。Method:1) apply 4.2in-lb.or rotate 180 and hold for 10seconds2).apply 15.5lb.t

36、ension hold for 10seconds in both perpendicular and parallel directions部件测试:所有可能产生安全危险的可被抓握的部件方法:1 施加4.2in-lb扭力或扭转180度，维持10秒3. 在水平和垂直方向上施加15.5lb拉力维持10秒Failure: any findings violate ASTM F963-96a失败所有违反ASTM F 963-96a 之结果Reliability可靠性Frequency: every shipment inspection周期：每批装运检验Sample size: 5 pieces e

37、ach type; accept 0 defect抽样数每款5pcs;可接受0缺陷Component test: all graspable parts which safety hazard may be revealed。Method方法1 apply 3in-lb or rotate 180and hold for 10second2.apply 12lb tension and seam tension hold for 10 seconds in both perpendicular and parallel directions1. 施加3in-lb扭力或扭转180度，维持10秒2

38、. 在水平和垂直方向上施加12lb拉力维持10秒Failure: any finding violate ASTM F963-96a or breakage or functional failure as defined in section 4.0 任何违反ASTM F963-96a 或损害或如4.0节中定义的功能失败Aging test老化试验Samples are left in an oven at 130+-5 for 48 hours and then equilibrate to room temperature 130烤箱中保持48小时然后移置于室温下Evaluation:评

39、估No safety hazards & functional damage 无安全危害及功能损害No rusting on the screw, chain& the metal parts 螺丝链条及金属部件未生锈No peeling off the label foil. Coating, glitter or metalizing (n.金属喷镀法),should be allowed after环境实验后无金属铂贴纸，涂层 发光物或金属剥落Cold storage test 冷藏测试Place sealed master carton in chamber or freezer at

40、 0+_5F for 1hour and then equilibrated(使平衡使相称 平均平衡) to room temperature将密封的卡通箱冷藏于0+-5F维持24+-1小时，然后移置于室温下EvaluationSurface coating adhesion test 涂层界油试验Frequency: every shipment inspection周期：每批装运检验Sample size 2 pieces each type; accept 0failure 每款2个， 可接受0缺陷Area: on all surface coating area面积: 所有涂层面积（面

41、积小于100mm2可不需进行此试验）Equipment 3M #810tape 仪器 3M#810胶纸Method: cut 9 straight and parallel lines, each square should be about 1mm2(area less than100mm2 does not need to apply) a stripe（条纹） of tape is applied on the coating surface and is pressed down thoroughly to remove all air bubbles, then pull the t

42、ape up in the direction perpendicular to the testing surface immediately,方法: 将涂层表面横竖各界9格，每格约为1mm2，将胶纸附在涂层表面并完全压平以挤出气泡，90+-30秒后将胶带以垂直方向迅速掀起。Failure: more than 5% substrate exposed 失败超出5%露出底色Transportation test 运输测试Transit test 运输测试Frequency： every shipment 周期每批装运检验Sample size 2cartons 抽样数 2箱Method: p

43、lace the master carton onto a shaker, shake for 2 hours方法: 震箱2小时Frequency of vibration 237rpm 震动频率237rpmDouble amplitude of vibration 1inch 振幅 1英寸Duration of vibration 120 minutes 持续时间120分钟Failure: any defects as described in section 4.0and any color migration, scuff mark and damage on packing.失败: 任

44、何如4.0节中所述之缺陷或任何色彩 擦花及包装损坏Carton drop投箱Frequency: every shipment inspection 周期: 每批装运检验Sample size: 2 cartons 抽样数 :2箱Method: 30 inches drop of 1 corner, 3 edges & 6 faces 方法30英寸1角x3边6面Failure: any findings violate ASTM F963 or breakage or functional failure as defined in section 4.0 失败: 所有ASTM F963 96

45、a 或损坏或如5.2节中的功能失败之结果Life testing 寿命Function life功能寿命测试Consecutive 6 phrases is one cycle 持续6节为一个周期When one cycle finish after 5 second process second cycle当一个周期完成5秒后再继续下一个周期Perform 2ooo cycles to the items basic function which was stated in section 4.0按照4.0所描述的基本功能直性2000周Sound testing 声音测试Area vocal

46、 test sample面积 有声音的测试样板Sample size 5 抽样数5Equipment: sound level meter& tunnel仪器: 声音分贝表管道Method: unit placed at 9.8 inches form the sound level meter in a sound insulation tunnel 方法: 单位放置在离声级分贝表9.8英寸的隔声管道中?Failure: any sample deviate from functional and safety requirement. Functional requirement: per

47、 section4.0失败: 任何违反功能及安全的要求Safety requirement :any unit its sound level smaller than 90Db 安全要求: 声级小于90DbRot molded PVC curing testing 搪胶PVC固化测试Area: rot molded PVC面积:? 搪胶PVCSample size 5 抽样数 5Equipment acetone仪器 丙酮Method 方法1. Sample preparation- select the thickest area or the position likely to hav

48、e to have cracking准备样板-选择最厚的面积或破裂的位置2. Bend the test sample so that the inner surface is shown outside弯曲测试样板以便从外面可以看到内里面3. Hold the bent sample in position with a locking clamp用灯将弯曲的样板锁定4. Add a layer (about 2-3droplets) of solution (100%acetone) on the inner surface of the test sample at the fold l

49、ine涂一层（大约2-3滴溶液（100%丙酮）在折叠样板的内里面5. Wait for 3 minutes and check the testing surface of rotomolded PVC等候3分钟再检查搪胶PVC的测试面Failure: a potential hazard caused by cracking or degrading of rotomolded PVC after a long period due to insufficient curring失败:破裂或失真的搪胶PVC长期固化后有潜在危险产生的可能date code marking日期印标记Date c

50、ode shall be appear on the product (except figures), the packing and the master carton.日期印必须标明于产品（公仔除外），包装及卡通箱上Date code format day & the year the item was produced i.e.14603: May 26 of 2003日期印编排的方式：产品生产的日/年，如：14603表示2003年5月26日note: compare any questionable units with the signed sample.附注:如有疑问请与洋行签板

51、对照wrong shipping mark 箱唛错误deviated printing and excessive contamination 印刷偏差或过于污染inspection for individual package 独立包装检验printing is deviated more than 1mm印刷偏差超过1mm污槽stain markany package which is peeled off or damaged more than 10mm is not acceptable 包装翘角或损坏超过100mm是不能接受的color uneven/different 颜色不均有

52、异scratch 刮花wrong wording on packaging 包装上有错误字母unripe of material 材料不全color deviated among all limbs 颜色有偏差soil 油渍discoloration &deformation as compared to the signed sample 与签板颜色偏差/变形inspection for plush (长毛绒,长毛绒做的, 豪华的, 舒服的)product 毛绒产品的检验the weight and product shall not be lighter with the signed s

53、ample产品重量与洋行签板不同tear of seam & cloth布/缝合处撕烂length of fray(磨损或散口) over 10mm磨损长度超过10mmwhite mark 顶白flow mark 气纹凹纹 sink mark披锋flushflush easily peel off or from 5 to 10 mm披锋易翘角或在5-10mm之间any burrs with sharp point or sharp edge 有利边或利尖安全的毛边deformation at any location 某些部位变形color varied from the signed sa

54、mple颜色与签板有异No detachable & broken parts which consider having safety hazard, such as sharp point and sharp edge, is allow under21lbs tension hold for 10 seconds or 4.2in-lbs or rotate 180 torque hold for 10 second test, but those without having safety hazard should conform to the requirements in att

55、achments,施加21lbs拉力或4.2in-lbs扭力或扭转180维持十秒，无被认为有安全危害的部件脱落或损坏，如利边和利角。但是无安全危害的部件应该和附件里的要求一致。Flexure跷曲Statement of conformity i.e. ”meets or exceed all safety requirements of the product safety code ASTM F963” 确定性说明：产品安全性代码符合或超出安全条例ASTM F963 96a/超出或符合产品安全代码ASTM F 963所有安全要求Correct UPC code 正确的UPC代码Individ

56、ual packing 独立包装Each product is to be window box pack 窗口盒包装Each window box pack included on piece instruction sheet 每个窗口盒中有说明书4 pieces per master carton 每箱装4pcsany product with wrong packing is not allowed 任何产品不允许包装错误This assortment ration is in product development stage for reference. The detailed

57、assortment ration must be referred to PO mentioned包装比率应参考产品发展的进程。详细分类情况查阅PO 之说明.-Lower torso LT. Of skipper左下身Shoulder LT. Of skipper左肩Lower arm LT. Of skipper 左下臂Hand LT. Of skipper左手RT. Upper leg low of skipper 右上腿下LT. Lower leg up of skipper 左下腿上Vest of skipper 长袍Neck joints of skipper颈较Lower leg

58、 rivets of skipper下腿钉Upper waist joints of skipper上腰较件Sound module发声盒试产(PP)PS正式生产 孩之宝要落货 ，其他公司不用？ 要签板？EP1第一次试模pre-production生产PS正式/开始生产最后工程办 (FEP) final engineering pilot安全试验及 QA sampleDECOA装饰/图案图-手板-模-生产please submit quotation accordingly. 请提出报价。搪胶植毛不良poor lockingdisposition 布置, 配置, 安排; 部署assortmen

59、t ratio 混装比例12pcs per TOY BIZ master carton每箱装12pcsassortment ratio per master carton 3sets per carton 每个卡通箱混装比例：每款3套。Look forward:向上移Except as provided herein, no right or license whatsoever, either expressed or implied, is granted to either party pursuant to this Agreement under any patent, patent

60、 application, or other proprietary right now or hereafter owned or controlled by the other party, and neither party shall be obligated by this Agreement to enter into any further agreement. 出来以上提到的信息，没有书面的或是暗指的权利或许可准予给任何一方依照此协议在任何专利，专利申请或其他所有权现在或以后被另一方拥有或控制，任何一方Outside lab report 公正行报告Ship mark外箱箱唛Product line flow chart 生产排位表Part list 塑料零件表