《报告指导博士》PPT课件.ppt
《《报告指导博士》PPT课件.ppt》由会员分享,可在线阅读,更多相关《《报告指导博士》PPT课件.ppt(9页珍藏版)》请在装配图网上搜索。
1、,1,Outline,1. Introduction 2. Experimental procedure 3. Results and discussion 4. Conclusions,2,Introduction,Considerable progress has been made in spatially resolved solar cell characterization with camera-based techniques. Important cell and material parameters, such as recombination lifetimes, tr
2、ap densities, power losses, shunt distributions, or diffusion lengths, can be imaged in a few minutes or sometimes even seconds. We perform recombination current and series resistance imaging on large-area crystalline silicon solar cells using a combined analysis of camera-based dark lock-in thermog
3、raphy DLIT and electroluminescence EL imaging. Combining the two images pixel by pixel allows us to calculate images of the local recombination current and thelocal series resistance of the solar cell.,3,Experimental procedure,The DLIT measurements are performed using an infrared camera sensitive in
4、 the wavelength range from 3.9 to 5 m, which is mounted in a dark chamber.11 A lock-in frequency of 20 Hz is used for all images generated in this study, which corresponds to a thermal diffusion length of 1.2 mm in silicon. The EL setup uses a Si charge coupled device CCD camera and is also mounted
5、in a dark box. Correct the EL images for stray light and dark noise by subtracting a dark image recorded at equal exposure time. During both measurements we connect the cells to a bipolar power source and measure the current and voltage using a four-point contacting scheme with 22 probes on each bus
6、 bar.,4,Results and discussion,5,6,有四個重要的結論 光學效果忽略電阻與電流密度的兩種圖像,限制量測均勻的晶片只能使用光學的量測方法,不均勻的晶片需更正紅外線的發光與發射率。 他們假設DLIT忽略電流流過所產生的熱,這樣的假設會使模組的電流上升13%。 假設外加電壓,這就使N結邊緣的空間電荷會超過原本的電流密度與載子濃度,這樣就能忽略費米能階的值,但在整個模組上是很微小的。 忽略銀膠的電阻,導致會低估總電阻值,值約0.1 cm2,7,他們提出使用複合電流與串聯電組成像的方法,再利用不同特徵技術,使相機擷取光與熱的訊號。 開創不損壞以及能夠快速檢測晶片特性的分析方法;與接觸式的檢測法比較量測速度,只有非常小的差異。 如果能夠結合光與熱訊號擷取技術,就能提高量測電阻值的靈敏度。 如果考慮光的不均勻性,也能利用在檢測多晶矽晶片。,8,Conclusions,Thank you for your attention,9,
- 温馨提示:
1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 装配图网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。