单片机毕业论文外文翻译1

《单片机毕业论文外文翻译1》由会员分享，可在线阅读，更多相关《单片机毕业论文外文翻译1（9页珍藏版）》请在装配图网上搜索。

1、英文文献Single-chipSCM is also known as micro-controller (Microcontroller Unit), commonly used letters of the acronym MCU that it was first used in industrial control.Only a single chip by the CPU chip developed from a dedicated processor. The first design is by a large number of peripherals and CPU on

2、a chip in the computer system, smaller, more easily integrated into a complex and demanding on the volume control device which. INTELsZ80 is the first designed in accordance with this idea processor, then on the development of microcontroller and dedicated processors have parted ways.Are 8-bit micro

3、controller early or4 bits. One of the most successful is the INTEL 8031, for a simple, reliable and good performance was a lot of praise. Then developed in 8031 out of MCS51 MCU Systems. SCM systems based on this system until now is still widely used. With the increased requirements of industrial co

4、ntrol field, began a 16-bit microcontroller, because the cost is not satisfactory but have not been very widely used. After 90 years with the great development of consumer electronics, microcontroller technology has been a huge increase. With INTEL i960 series, especially the later series of widely

5、used ARM, 32-bit microcontroller quickly replace high-end 16-bit MCU status and enter the mainstream market. The traditional 8-bit microcontroller performance have been the rapid increase capacity increase compared to 80 the number of times. Currently, high-end 32-bit microcontroller clocked over 30

6、0MHz, the performance catching the mid-90s dedicated processor, while the average model prices fall to one U.S. dollars, the most high-end model only 10 dollars.Modern SCM systems are no longer only in the development and use of bare metal environment, a large number of proprietary embedded operatin

7、g system is widely used in the full range of SCM. The handheld computers and cell phones as the core processing of high-end microcontroller can even use a dedicated Windows and Linux operating systems.SCM is more suitable than the specific processor used in embedded systems, so it was up to the appl

8、ication. In fact the number of SCM is the worlds largest computer. Modern human life used in almost every piece of electronic and mechanical products will be integrated single chip.Phone, telephone, calculator, home appliances, electronic toys, handheld computers and computer accessories such as a m

9、ouse with a 1-2 in both the Department of SCM. Personal computer will have a large number of SCM in the work. General car with more than 40 SCM, complex industrial control systems may even have hundreds of SCM in the same time work! SCM is not only far exceeds the number of PC and other computing th

10、e sum, or even more than the number of human beingsSingle chip, also known as single-chip microcontroller, it is not complete a certain logic chips, but to a computer system integrated into a chip.Equivalent to a micro-computer, and computer than just the lack of a microcontroller I / O devices. Gen

11、eral talk: a chip becomes a computer. Its small size, light weight, cheap, for the study, application and development of facilities provided. At the same time, learning to use the MCU is to understand the principle and structure of the computer the best choice.SCM and the computer functions internal

12、ly with similar modules, such as CPU, memory, parallel bus, the same effect as well, and hard disk memory devices, and different is its performance of these components were relatively weak many of our home computer, but the price is low , usually not more than 10 yuan you can do with it . some contr

13、ol for a class is not very complicated electrical work is enough of. We are using automatic drum washing machine, smoke hood, VCD and so on appliances which could see its shadow! It is primarily as a control section of the core componentsIt is an online real-time control computer, control-line is th

14、at the scene is needed is a stronger anti-jamming ability, low cost, and this is, and off-line computer (such as home PC), the main difference.MCU is through running, and can be modified. Through different procedures to achieve different functions, in particular special unique features, this is anot

15、her device much effort needs to be done, some great efforts are very difficult to do. A not very complex functions if the 50s with the United States developed 74 series, or the 60s CD4000 series of these pure hardware buttoned, then the circuit must be a large PCB board! But if the United States if

16、the 70s with a series of successful SCM market, the result will be a drastic change! Just because you are prepared by microcomputer programs can achieve high intelligence, high efficiency and high reliability!As the microcontroller on the cost-sensitive, so now the dominant software or the lowest le

17、vel assembly language, which is the lowest level in addition to more than binary machine code language, and as so low why is the use? Many high-level language has reached the level of visual programming Why is not it? The reason is simply that there is no home computer as a single chip CPU, not as h

18、ard as a mass storage device.A visualization of small high-level language program which even if only one button, will reach tens of K of size! For the home PCs hard drive in terms of nothing, but in terms of the MCU is not acceptable. SCM in the utilization of hardware resources to be very high for

19、the job so although the original is still in the compilation of a lot of use. The same token, if the giant computer operating system and applications run up to get home PC, home PC, also can not afford to.Can be said that the twentieth century across the three power era, that is, the age of electric

20、ity, the electronic age and has entered into the computer age. However, this computer, usually refers to the personal computer, referred to as PC. It consists of the host, keyboard, monitor and other components. Another type of computer, most people do not know how. This computer is to give all kind

21、s of intelligent machines single chip (also known as micro-controller). As the name suggests, this computer system took only a minimal integrated circuit, can be a simple operation and control. Because it is small, usually hidden in the charged mechanical stomach in. It is in the device, like the hu

22、man brain plays a role, it goes wrong, the whole plant was paralyzed. Now, this microcontroller has a very broad field of use, such as smart meters, real-time industrial control, communications equipment, navigation systems, and household appliances. Once all kinds of products were using SCM, can se

23、rve to upgrade the effectiveness of products, often in the product name preceded by the adjective - intelligent, such as intelligent washing machines. Now some technical personnel of factories or other amateur electronics developers to engage in out of certain products, not the circuit is too compli

24、cated, that function is too simple and can easily be copied. The reason may be stuck in the product did not use a microcontroller or other programmable logic device.The six important part of studying MCU: First, Bus:We know that a circuit is always made by the devices connected by wires, in analog c

25、ircuits, the connection does not become a problem because the device is a serial relationship between the general, the device is not much connection between the , but the computer is not the same circuit, it is a microprocessor core, the device must be connected with the microprocessor, the device m

26、ust be coordination between, so they need to connect on a lot, as if still analog circuit like the microprocessor and devices in the connection between the individual, the number of lines will be a little more surprising, therefore the introduction of the microprocessor bus Zhong Each device Gongton

27、g access connections, all devices 8 Shuju line all received eight public online, that is the equivalent of all devices together in parallel, but only this does not work, if there are two devices send data at the same time, a 0, a 1, then, whether the receiver received what is it? This situation is n

28、ot allowed, so to be controlled by controlling the line, time-sharing the device to work at any time only one device to send data (which can have multiple devices to receive both). Devices data connection is known as the data bus, the device is called line of control all the control bus. Internal or

29、 external memory in the microcontroller and other devices have memory cells, the memory cell to be assigned addresses, you can use, distribution, of course, to address given in the form of electrical signals, and as more memory cells, so, for the address allocation The line is also more of these lin

30、es is called the address bus.Second, data, address, command.The reason why these three together because of the nature of these three are the same - the number, or are a string of 0 and 1 form the sequence. In other words, addresses, instructions are also data. Instruction: from single chip designer

31、provides a number of commonly used instructions with mnemonic we have a strict correspondence between the developer can not be changed by the MCU. Address: the search for MCU internal, external storage units, input and output port based on the address of the internal unit value provided by the chip

32、designer is good, can not be changed, the external unit can be single chip developers to decide, but there are a number of address units is a must. Third, P0 port, P2 and P3 of the second function I use: Beginners often on the P0 port, P2 and P3 port I use the second function puzzled that the second

33、 function and have a switch between the original function of the process, or have a directive, in fact, the port The second feature is automatic, do not need instructions to convert. Such as P3.6, P3.7 respectively WR, RD signal, when the microchip processing machines external RAM or external I / O

34、port, they are used as a second function, not as a general-purpose I / O port used, so long as a A microprocessor implementation of the MOVX instruction, there will be a corresponding signal sent from the P3.6 or P3.7, no prior use of commands. In fact not as a general-purpose I / O port use is also

35、 not a no but (user) not as a general-purpose I / O port to use. You can arrange the order of a SETB P3.7s instructions, and when the MCU execution to the instruction, the also make P3.7 into a high, but users will not do so because this is usually will cause the system to collapse.Fourth, the progr

36、ams implementation:Reduction in power after the 8051 microcontroller within the program counter (PC) in the value of 0000 , the process is always from the 0000 units started, that is: the system must exist in ROM 0000 this unit , and in 0000 unit must be stored in a single instruction. Five, the sta

37、ck: Stack is a region, is used to store data, there is no special about the region itself is a part of internal RAM, special access to its data storage and the way that the so-called advanced post out backward first out , and the stack has a special data transmission instructions that PUSH and POP ,

38、 has a special expertise in its services unit, that is, the stack pointer SP, whenever a PUSH instruction execution, SP on (in the Based on the original value) automatically add 1, whenever the implementation of a POP instruction, SP will (on the basis of the original value) automatically by 1. As t

39、he SP values can be changed with the instructions, so long as the beginning of the process to change the value of the SP, you can set the stack memory unit required, such as the program begins, with an MOV SP, # 5FH instructions When set on the stack starting from the memory unit 60H unit. There is

40、always the beginning of the general procedure with such a directive to set the stack pointer, because boot, SP initial value of 07H, 08H This unit from the beginning to stack next, and 08H to 1FH 8031 is the second in the region, three or four working register area, often used, this will lead to con

41、fusion of data. Different authors when writing programs, initialize the stack is not exactly the same directive, which is the authors habit. When set up the stack zone, does not mean that the region become a special memory, it can still use the same memory region as normal, but generally the program

42、mer does not regard it as an ordinary memory used.中文翻译单片机单片机也被称为微控制器（Microcontroller Unit），常用英文字母的缩写MCU表示单片机，它最早是被用在工业控制领域。单片机由芯片内仅有CPU的专用处理器发展而来。最早的设计理念是通过将大量外围设备和CPU集成在一个芯片中，使计算机系统更小，更容易集成进复杂的而对体积要求严格的控制设备当中。INTEL的Z80是最早按照这种思想设计出的处理器，从此以后，单片机和专用处理器的发展便分道扬镳。 早期的单片机都是8位或4位的。其中最成功的是INTEL的8031，因为简单可靠而

43、性能不错获得了很大的好评。此后在8031上发展出了MCS51系列单片机系统。基于这一系统的单片机系统直到现在还在广泛使用。随着工业控制领域要求的提高，开始出现了16位单片机，但因为性价比不理想并未得到很广泛的应用。90年代后随着消费电子产品大发展，单片机技术得到了巨大提高。随着INTEL i960系列特别是后来的ARM系列的广泛应用，32位单片机迅速取代16位单片机的高端地位，并且进入主流市场。而传统的8位单片机的性能也得到了飞速提高，处理能力比起80年代提高了数百倍。目前，高端的32位单片机主频已经超过300MHz，性能直追90年代中期的专用处理器，而普通的型号出厂价格跌落至1美元，最高端的

44、型号也只有10美元。当代单片机系统已经不再只在裸机环境下开发和使用，大量专用的嵌入式操作系统被广泛应用在全系列的单片机上。而在作为掌上电脑和手机核心处理的高端单片机甚至可以直接使用专用的Windows和Linux操作系统。 单片机比专用处理器更适合应用于嵌入式系统，因此它得到了最多的应用。事实上单片机是世界上数量最多的计算机。现代人类生活中所用的几乎每件电子和机械产品中都会集成有单片机。手机、电话、计算器、家用电器、电子玩具、掌上电脑以及鼠标等电脑配件中都配有1-2部单片机。而个人电脑中也会有为数不少的单片机在工作。汽车上一般配备40多部单片机，复杂的工业控制系统上甚至可能有数百台单片机在同时

45、工作！单片机的数量不仅远超过PC机和其他计算的总和，甚至比人类的数量还要多。 单片机又称单片微控制器,它不是完成某一个逻辑功能的芯片,而是把一个计算机系统集成到一个芯片上。相当于一个微型的计算机，和计算机相比，单片机只缺少了I/O设备。概括的讲：一块芯片就成了一台计算机。它的体积小、质量轻、价格便宜、为学习、应用和开发提供了便利条件。同时，学习使用单片机是了解计算机原理与结构的最佳选择。 单片机内部也用和电脑功能类似的模块，比如CPU，内存，并行总线，还有和硬盘作用相同的存储器件，不同的是它的这些部件性能都相对我们的家用电脑弱很多，不过价钱也是低的，一般不超过10元即可.用它来做一些控制电器一

46、类不是很复杂的工作足矣了。我们现在用的全自动滚筒洗衣机、排烟罩、VCD等等的家电里面都可以看到它的身影！它主要是作为控制部分的核心部件。 它是一种在线式实时控制计算机，在线式就是现场控制，需要的是有较强的抗干扰能力，较低的成本，这也是和离线式计算机的（比如家用PC）的主要区别。 单片机是靠程序运行的，并且可以修改。通过不同的程序实现不同的功能，尤其是特殊的独特的一些功能，这是别的器件需要费很大力气才能做到的，有些则是花大力气也很难做到的。一个不是很复杂的功能要是用美国50年代开发的74系列，或者60年代的CD4000系列这些纯硬件来搞定的话，电路一定是一块大PCB板！但是如果要是用美国70年代

47、成功投放市场的系列单片机，结果就会有天壤之别！只因为单片机的通过你编写的程序可以实现高智能，高效率，以及高可靠性！ 由于单片机对成本是敏感的，所以目前占统治地位的软件还是最低级汇编语言，它是除了二进制机器码以上最低级的语言了，既然这么低级为什么还要用呢？很多高级的语言已经达到了可视化编程的水平为什么不用呢？原因很简单，就是单片机没有家用计算机那样的CPU，也没有像硬盘那样的海量存储设备。一个可视化高级语言编写的小程序里面即使只有一个按钮，也会达到几十K的尺寸！对于家用PC的硬盘来讲没什么，可是对于单片机来讲是不能接受的。 单片机在硬件资源方面的利用率必须很高才行，所以汇编虽然原始却还是在大量使

48、用。一样的道理，如果把巨型计算机上的操作系统和应用软件拿到家用PC上来运行，家用PC的也是承受不了的。 可以说，二十世纪跨越了三个“电”的时代，即电气时代、电子时代和现已进入的电脑时代。不过，这种电脑，通常是指个人计算机，简称PC机。它由主机、键盘、显示器等组成。还有一类计算机，大多数人却不怎么熟悉。这种计算机就是把智能赋予各种机械的单片机（亦称微控制器）。顾名思义，这种计算机的最小系统只用了一片集成电路，即可进行简单运算和控制。因为它体积小，通常都藏在被控机械的“肚子”里。它在整个装置中，起着有如人类头脑的作用，它出了毛病，整个装置就瘫痪了。现在，这种单片机的使用领域已十分广泛，如智能仪表、

49、实时工控、通讯设备、导航系统、家用电器等。各种产品一旦用上了单片机，就能起到使产品升级换代的功效，常在产品名称前冠以形容词“智能型”，如智能型洗衣机等。现在有些工厂的技术人员或其它业余电子开发者搞出来的某些产品，不是电路太复杂，就是功能太简单且极易被仿制。究其原因，可能就卡在产品未使用单片机或其它可编程逻辑器件上。 单片机学习的六大重要部分：一、总线：我们知道，一个电路总是由元器件通过电线连接而成的，在模拟电路中，连线并不成为一个问题，因为各器件间一般是串行关系，各器件之间的连线并不很多，但计算机电路却不一样，它是以微处理器为核心，各器件都要与微处理器相连，各器件之间的工作必须相互协调，所以需

50、要的连线就很多了，如果仍如同模拟电路一样，在各微处理器和各器件间单独连线，则线的数量将多得惊人，所以在微处理机中引入了总线的概念，各个器件共同享用连线，所有器件的8根数据线全部接到8根公用的线上，即相当于各个器件并联起来，但仅这样还不行，如果有两个器件同时送出数据，一个为0，一个为1，那么，接收方接收到的究竟是什么呢？这种情况是不允许的，所以要通过控制线进行控制，使器件分时工作，任何时候只能有一个器件发送数据（可以有多个器件同时接收）。器件的数据线也就被称为数据总线，器件所有的控制线被称为控制总线。在单片机内部或者外部存储器及其它器件中有存储单元，这些存储单元要被分配地址，才能使用，分配地址当

51、然也是以电信号的形式给出的，由于存储单元比较多，所以，用于地址分配的线也较多，这些线被称为地址总线。 二、数据、地址、指令：之所以将这三者放在一起，是因为这三者的本质都是一样的数字，或者说都是一串0和1组成的序列。换言之，地址、指令也都是数据。指令：由单片机芯片的设计者规定的一种数字，它与我们常用的指令助记符有着严格的一一对应关系，不可以由单片机的开发者更改。地址：是寻找单片机内部、外部的存储单元、输入输出口的依据，内部单元的地址值已由芯片设计者规定好，不可更改，外部的单元可以由单片机开发者自行决定，但有一些地址单元是一定要有的。 三、P0口、P2口和P3的第二功能用法：初学时往往对P0口、P

52、2口和P3口的第二功能用法迷惑不解，认为第二功能和原功能之间要有一个切换的过程，或者说要有一条指令，事实上，各端口的第二功能完全是自动的，不需要用指令来转换。如P3.6、P3.7分别是WR、RD信号，当微片理机外接RAM或有外部I/O口时，它们被用作第二功能，不能作为通用I/O口使用，只要一微处理机一执行到MOVX指令，就会有相应的信号从P3.6或P3.7送出，不需要事先用指令说明。事实上不能作为通用I/O口使用也并不是不能而是（使用者）不会将其作为通用I/O口使用。你完全可以在指令中按排一条SETB P3.7的指令，并且当单片机执行到这条指令时，也会使P3.7变为高电平，但使用者不会这么去做

53、，因为这通常会导致系统的崩溃。四、程序的执行过程：单片机在通电复位后8051内的程序计数器（PC）中的值为0000，所以程序总是从0000单元开始执行，也就是说：在系统的ROM中一定要存在0000这个单元，并且在0000单元中存放的一定是一条指令。 五、堆栈：堆栈是一个区域，是用来存放数据的，这个区域本身没有任何特殊之处，就是内部RAM的一部份，特殊的是它存放和取用数据的方式，即所谓的先进后出，后进先出，并且堆栈有特殊的数据传输指令，即PUSH和POP，有一个特殊的专为其服务的单元，即堆栈指针SP，每当执一次PUSH指令时，SP就（在原来值的基础上）自动加1，每当执行一次POP指令，SP就（在

54、原来值的基础上）自动减1。由于SP中的值可以用指令加以改变，所以只要在程序开始阶段更改了SP的值，就可以把堆栈设置在规定的内存单元中，如在程序开始时，用一条MOV SP，#5FH指令，就时把堆栈设置在从内存单元60H开始的单元中。一般程序的开头总有这么一条设置堆栈指针的指令，因为开机时，SP的初始值为07H，这样就使堆栈从08H单元开始往后，而08H到1FH这个区域正是8031的第二、三、四工作寄存器区，经常要被使用，这会造成数据的混乱。不同作者编写程序时，初始化堆栈指令也不完全相同，这是作者的习惯问题。当设置好堆栈区后，并不意味着该区域成为一种专用内存，它还是可以象普通内存区域一样使用，只是一般情况下编程者不会把它当成普通内存用了。