【BS英国标准】BS EN 76432002 pressure equipment Part 3 Definition of parties involved

《【BS英国标准】BS EN 76432002 pressure equipment Part 3 Definition of parties involved》由会员分享，可在线阅读，更多相关《【BS英国标准】BS EN 76432002 pressure equipment Part 3 Definition of parties involved（9页珍藏版）》请在装配图网上搜索。

1、BRITISH STANDARDBS EN764-3:2002Pressure equipment Part 3: Definition of parties involvedThe European Standard EN 764-3:2002 has the status of aBritish StandardICS 01.040.23; 23.020.30NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 764-3:2002National forewordThis British S

2、tandard is the official English language version ofEN 764-3:2002.The UK participation in its preparation was entrusted to Technical CommitteePVE/1, Pressure vessels, which has the responsibility to:aid enquirers to understand the text;present to the responsible international/European committee any e

3、nquiries on the interpretation, or proposals for change, and keep the UK interests informed;monitor related international and European developments and promulgate them in the UK.A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe Brit

4、ish Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Onl

5、ine.This publication does not purport to include all the necessary provisions of a contract. Users of this publication are responsible for their correct application.Compliance with a British Standard does not of itself confer immunity from legal obligations.This British Standard, having been prepare

6、d under the direction of the Engineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 13 June 2002 BSI 13 June 2002ISBN 0 580 39864 1Summary of pagesThis document comprises a front cover, an inside front cover, the EN title

7、 page,pages 2 to 5 and a back cover.The BSI copyright date displayed in this document indicates when the document was last issued.Amd. No.DateCommentsAmendments issued since publicationEUROPEAN STANDARD NORME EUROPENNEEUROPISCHE NORMEN 764-3May 2002ICS 01.040.23; 23.020.30English versionPressure equ

8、ipment - Part 3: Definition of parties involvedEquipements sous pression - Partie 3: Dfinition des parties impliquesDruckgerte - Teil 3: Definition der beteiligten ParteienThis European Standard was approved by CEN on 29 April 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regula

9、tions which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member.This Europe

10、an Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions.CEN members are the national

11、standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATION C O M I T EUR O P EN DE NOR M A L I S A TI

12、ON EUR O P I S C H ES KOM I TEE F R NOR M UNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2002 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members.Ref. No. EN 764-3:2002 EEN 764-3:2002 (E)ContentspageForeword .31Scope .42Terms and definit

13、ions.45ForewordThis document EN 764-3:2002 has been prepared by Technical Committee CEN/TC 54 Unfired pressure vessels, the secretariat of which is held by BSI.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at th

14、e latest by November 2002, and conflicting national standards shall be withdrawn at the latest by November 2002.This document has been prepared under a mandate given to CEN by the European Commission (EC) and theEuropean Free Trade AssociationThis European Standard consists of seven parts which are:

15、 Part 1Definitions of pressure, temperature and volume; Part 2Quantities, symbols and units;Part 3Definition of parties involved;Part 4Establishment of technical delivery conditions for metallic materials;Part 5Inspection documentation of metallic materials and compliance with the material specifica

16、tion; Part 6Operating instructions;Part 7Safety systems for unfired pressure equipment.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,

17、 France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.1ScopeThis European Standard defines terms and definitions of parties involved in the design, manufacture, testing and inspection of pressure equipme

18、nt and assemblies addressed by the European Directive 97/23/EC.2Terms and definitions2.1material manufacturerindividual or organisation that produces material in the basic product forms used in the manufacture of pressure equipment2.2material supplierindividual or organisation, that may or may not b

19、e the material manufacturer, who supplies material or parts used in the manufacture of pressure equipment and assemblies2.3 manufacturerindividual or organisation that is responsible for the design, fabrication, testing, inspection, installation of pressure equipment and assemblies where relevantNOT

20、E 1The manufacturer can subcontract one or more of the above mentioned tasks under its responsibility.NOTE 2In EU member states the manufacturer is responsible for compliance with the Pressure Equipment Directive97/23/EC. For those manufacturers outside of the EU their authorized representative insi

21、de the EU assumes this responsibility.2.4designer, fabricator and/or installer, subcontractor of the manufacturerindividual or organisation that respectively performs design, fabrication, testing, installation where relevant, of pressure equipment under contract to the manufacturer2.5first partyindi

22、vidual or organisation that designs, manufactures or supplies the pressure equipment or the assembly2.6second partyindividual or organisation that uses and/or operates the pressure equipment or the assembly2.7third partyindividual or organisation independent of the first and second partyNOTEInspecto

23、rs of the suppliers of material, manufacturers, fabricators/installers or their subcontractors are not third party inspectors.2.8user and/or operatorindividual or organisation that uses and/or operates pressure equipment or assemblies2.9 purchaserindividual or organisation that buys pressure equipme

24、nt, assemblies or pressure parts on behalf of the user and/or operator or for its own use2.10 inspectorindividual who is independent from production responsible for carrying out inspections to verify that the requirements of the technical specification(s) are met2.11responsible authoritycompetent or

25、ganisation which is independent of the manufacturer. For application within the jurisdiction of the European Union this organisation may be a notified body, a recognised third-party organisation or an user inspectorate. For application outside the jurisdiction of the European Union this organisation

26、 may be a government regulating body or an independent inspection authority. For the purpose of this standard all these organisations have been collectively termed responsible authority (RA)2.12notified bodyorganisation according to the Article 12 of the Pressure Equipment Directive 97/23/ECNOTEThe

27、names and tasks of the notified bodies are published in the Official Journal of the European Communities.2.13recognized third-party organizationorganisation according to the Article 13 of the Pressure Equipment Directive 97/23/ECNOTEThe names and tasks of the recognised third-party organisations are

28、 published in the Official Journal of theEuropean Communities.2.14user inspectorateorganisation according to the Article 14 of the Pressure Equipment Directive 97/23/ECA user inspectorate acts exclusively for the group of which it is part. The names and tasks of the user inspectorate are not publish

29、ed in the Official Journal of the European Communities. The designation of an user inspectorate is optional for the Member States.BS EN 764-3:2002BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparingBritish Standards. It

30、presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users ofBritish Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BS

31、I to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover.Tel: +44 (0)20 89

32、96 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer S

33、ervices. Tel: +44 (0)20 8996 9001.Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are alsoavailable from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standard

34、s, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all i

35、ts products and services. Contact the Information Centre.Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other

36、 benefits contact Membership Administration.Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001.Email: membershipbsi-.Information regarding online access to British Standards via British StandardsOnline can be found at http:/www.bsi-Further information about BSI is available on the BSI website at htt

37、p:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system

38、or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553.Email: copyrightbsi-.国内外标准大全豆丁网国内外标准下载地址