QCT2591998标准英文版
《QCT2591998标准英文版》由会员分享,可在线阅读,更多相关《QCT2591998标准英文版(3页珍藏版)》请在装配图网上搜索。
1、QC/T 259-1998 PrefaceThis standard adopts the Japan Standard of JASO C614 87 as a major reference.The standard is presented by Mechanical Industry Bureau of China.The standard is under the jurisdiction of Auto Standardization Technical Committee of China.The standard is drafted by Shiyan Wheel and R
2、im Research Institute.The major draftsman: Yu Chuanming Auto Industry Standard of the P.R.C QC/T 259-1998Requirements and Test Methods on the Welding Intensity of the Wheel Rims/Wheel Spokes1 ScopeThis standard stipulated the requirement and test methods on the welding intensity of the wheel rims/wh
3、eel spokesThis standard applies to the steel wheels using 5 DC wheel rims.2 Test SamplesTest samples should finish all processing procedures, except coating.3 Intensity RequirementsUnder the test load, No tear or visible cracks should occur on the welding position of the rims or spokes.4 Test Equipm
4、entThe test equipment is showed as the following diagram: Lower tooling Spoke Upper tooling RimLoadTest equipment should meet with the following:1) The clearance between the interior side of the spoke and the upper tooling is 23mm;2) The clearance between the outside of the spoke and the lower tooli
5、ng is 23mm;3) The upper tooling and the spokes, the lower tooling and the rims should closely matched with each other 4) Load machine is hydraulic.Mechanical Industry Bureau Approved 1998-12-16 Implemented July, 1st, 1999QC/T 259 -19985 Test MethodsAs exhibited in the diagram above, the side surface
6、 of the rims should closely contact the lower tooling, and the load is on the interior side of the spokes, and the welding positions of the rims/spokes should be loaded evenly.The load should be slowly increment to the specified value as showed in the following table.6 Test LoadTest Load as per the following table: The smaller value of thickness of the plate material of the rims and spokes (mm)Load (kN/Kfg)
- 温馨提示:
1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 装配图网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。