欧洲纤维标准(EN-fiber-standards)

《欧洲纤维标准(EN-fiber-standards)》由会员分享，可在线阅读，更多相关《欧洲纤维标准(EN-fiber-standards)（69页珍藏版）》请在装配图网上搜索。

1、欧洲纤维原则(EN fiber standards)ANSI| BS| DIN| EN| GB| ISO| JIS| NF| DIC 编号中文名称英文名称EN 1013-2-1998 单层顶盖用透光齿形塑料板 第2部分：玻璃纤维增强的聚脂树脂薄板的特殊规定和实验措施 Light transmitting profiled plastic sheeting for single skin roofing - Part 2: Specific requirements and test methods for sheets of glass fibre reinforced polyester r

2、esin (GRP) EN 1094-1-1997 绝缘耐火产品 第1部分：陶瓷纤维产品术语 Insulating refractory products - Part 1: Terminology for ceramic fibre products EN 1094-3- 绝缘耐火产品 第3部分：陶瓷纤维制造的绝缘产品分类 Insulating refractory products - Part 3: Classification of insulating products made from ceramic fibres EN 1169-1999 预制混凝土制品 玻璃纤维增强水泥厂生产

3、控制的一般规则 Precast concrete products - General rules for factory production control of glass-fibre reinforced cement EN 1170-1-1997 预制混凝土制品 玻璃纤维增强水泥实验措施 第1部分：“坍塌实验”法 测量基质结实度 Precast concrete products - Test method for glass-fibre reinforced cement - Part 1: Measuring the consistency of the matrix Slump

4、 test method EN 1170-2-1997 预制混凝土制品 玻璃纤维增强水泥实验措施 第2部分：新玻璃纤维增强水泥中纤维含量的测量 冲刷实验 Precast concrete products - Test method for glass-fibre reinforced cement - Part 2: Measuring the fibre content in fresh GRC, Wash out test EN 1170-3-1997 预制混凝土制品 玻璃纤维增强水泥的实验措施 第3部分：喷射玻璃纤维增强水泥中纤维含量的测量 Precast concrete produ

5、cts - Test method for glass-fibre reinforced cement - Part 3: Measuring the fibre content of sprayed GRC EN 1170-4-1997 预制混凝土制品 玻璃纤维增强水泥的实验措施 第4部分：测定抗弯强度 简化弯曲实验法 Precast concrete products - Test method for glass-fibre reinforced cement - Part 4: Measuring bending strength, Simplified bending test me

6、thod EN 1170-5-1997 预制混凝土制品 玻璃纤维增强水泥的实验措施 第5部分：测定抗弯强度 完全弯曲实验法 Precast concrete products - Test method for glass-fibre reinforced cement - Part 5: Measuring bending strength, Complete bending test method EN 1170-6-1997 预制混凝土产品 玻璃纤维增强水泥的实验措施 第6部分：浸渍法对水吸取的测定和干密度的测定 Precast concrete products - Test meth

7、od for glass-fibre reinforced cement - Part 6: Determination of the absorption of water by immersion and determination of the dry density EN 1170-7-1997 预制混凝土制品 玻璃纤维增强水泥的实验措施 第7部分：由于湿度引起尺寸变化的极限的测定 Precast concrete products - Test method for glass-fibre reinforced cement - Part 7: Measurement of extr

8、emes of dimensional variations due to moisture content EN 12132-1-1998 羽毛和羽绒纤维羽绒透气性能的实验措施摩擦实验 Feather and down - Methods of testing the down proof properties of fabrics - Part 1: Rubbing test EN 12132-2-1998 羽毛和羽绒纤维羽绒透气性能的实验措施冲击实验 Feather and down - Methods of testing the down proof properties of fa

9、brics - Part 2: Impact test EN 12195-2- 道路车辆的货品约束装置安全第2部分：人造纤维捆绑带 Load restraint assemblies on road vehicles - Safety - Part 2: Web lashing made from man-made fibres EN 12369-1- 木基板构造设计特性值第1部分： OSB、颗粒板和纤维板 Wood-based panels - Characteristic values for structural design - Part 1: OSB, particleboards

10、and fibreboards EN 12467-+AC- 纤维胶合平板产品规格和实验措施 Fibre-cement flat sheets - Product specifications and test methods / Note: To be replaced by prEN 12467 (-08). EN 12575-1998 塑料热固模塑物料SMC中纤维浸湿限度的测定 Plastics - Thermoset moulding compounds - Determination of the degree of fibre wet out in SMC EN 12576-1998

11、 塑料纤维增强复合物SMC、BMC和DMC的压缩模制实验板的制备 Plastics - Fibre reinforced composites - Preparation of compression moulded test plates of SMC, BMC and DMC EN 12590-1999 纺织品完全或部分用合成纤维制的工业缝纫线 Textiles - Industrial sewing threads made wholly or partly from synthetic fibres EN 1261-1995 一般用途纤维绳索 大麻绳 Fibre ropes for g

12、eneral service - Hemp EN 12654-1-1998 纺织玻璃纤维纱第部分：名称 Textile glass - Yarns - Part 1: Designation EN 12654-2-1998 纺织玻璃纤维纱第部分：实验措施和一般规范 Textile glass - Yarns - Part 2: Methods of test and general specifications EN 12654-3-1998 纺织玻璃纤维纱第部分：一般应用的一般规定 Textile glass - Yarns - Part 3: General requirements fo

13、r general applications EN 12710-1999 纤维板柱桶公称容量为15升至250升的带封闭环的可移动头(开口)式桶 Fibreboard drums - Removable head (open head) drums with closing rings with a nominal capacity of 15 l to 250 l EN 12751-1999 纺织品实验用纤维、纱和织物的抽样 Textiles - Sampling of fibres, yarns and fabrics for testing EN 12763- 建筑物排水系统的纤维胶合管及

14、附件 交货尺寸和技术术语 Fibre-cement pipes and fittings for discharge systems for buildings - Dimensions and technical terms of delivery EN 12971-1-1999 加强材料 纺织玻璃纤维碎丝规范 第1部分：名称 Reinforcements - Specification for textile glass chopped strands - Part 1: Designation EN 12971-2-1999 加强材料 纺织玻璃纤维碎丝规范 第2部分：实验措施和一般规定

15、Reinforcements - Specification for textile glass chopped strands - Part 2: Test methods and general requirements EN 12971-3-1999 加强材料 纺织玻璃纤维碎丝规范 第3部分：特殊需求 Reinforcements - Specification for textile glass chopped strands - Part 3: Specific requirements EN 13002-2-1999 碳纤维纱 第2部分：实验措施和通用规范 Carbon fibre

16、 yarns - Part 2: Test methods and general specifications EN 13003-1-1999 聚酰胺纤维丝线 第1部分：名称 Para-aramid fibre filament yarns - Part 1: Designation EN 13003-2-1999 聚酰胺纤维丝线 第2部分：实验措施和通用规范 Para-aramid fibre filament yarns - Part 2: Methods of test and general specifications EN 13003-3-1999 聚酰胺纤维丝线 第3部分：技术

17、规范 Para-aramid fibre filament yarns - Part 3: Technical specifications EN 13171- 建筑物保温制品 工厂预制木质纤维（WF）制品 规范 Thermal insulation products for buildings - Factory made wood fibre (WF) products - Specification EN 13280- 单件式和预制构件拼装构造的玻璃纤维加强地上冷水蓄水池规范 Specification for glass fibre reinforced cisterns of one

18、 piece and sectional construction, for the storage, above ground, of cold water EN 13413- 弹性地板覆盖物 填充纤维底板上的聚氯乙烯地面覆盖物 规范 Resilient floor coverings - Polyvinyl chloride floor coverings on a filled fibrous backing - Specification EN 13496- 建筑物保温品 玻璃纤维网机械性能测定 Thermal insulation products for building appl

19、ications - Determination of the mechanical properties of glass fibre meshes EN 13558- 家用沐浴器底盘用冲压成形挤压聚丙烯脯纤维板规范 Specifications for impact modified extruded acrylic sheets for shower trays for domestic purposes EN 14020-1- 增强物纺织玻璃纤维纤维粗纱的规格第1部分：命名 Reinforcements - Specification for textile glass rovings

20、 - Part 1: Designation EN 14020-2- 增强物纺织玻璃纤维粗纱的规格第2部分：检查措施和一般规定 Reinforcements - Specification for textile glass rovings - Part 2: Methods of test and general requirements EN 14020-3- 增强物纺织玻璃纤维粗纱的规格第2部分：特殊规定 Reinforcements - Specification for textile glass rovings - Part 3: Specific requirements EN

21、14053- 包装由波纹或实心纤维板制造的包装材料型号和构造 Packaging - Packagings manufactured from corrugated or solid fibreboard - Types and construction EN 14118-1- 增强 纺织玻璃纤维垫规范（短切原丝薄毡和持续纤维薄毡） 第1部分：名称 Reinforcement - Specifications for textile glass mats (chopped strand and continuous filament mats) - Part 1: Designation EN

22、 14118-2- 增强 纺织玻璃纤维垫规范（短切原丝薄毡和持续纤维薄毡） 第2部分：一般规定和实验措施 Reinforcement - Specifications for textile glass mats (chopped strand and continuous filament mats) - Part 2: Methods of test and general requirements EN 14118-3- 增强 纺织玻璃纤维垫规范（短切原丝薄毡和持续纤维薄毡） 第3部分：特殊规定 Reinforcement - Specifications for textile gla

23、ss mats (chopped strand and continuous filament mats) - Part 3: Specific requirements EN 14362-2- 纺织品 从偶氨着色剂衍化的某些芳族胺的测定措施 第2部分：用萃取纤维法获得使用某些偶氮着色剂的检测 Textiles - Methods for determination of certain aromatic amines derived from azo colorants - Part 2: Detection of the use of certain azo colorants acces

24、sible by extracting the fibres EN 1444- 纤维水泥管道 现场工作实践和铺设指南 Fibre-cement pipelines - Guide for laying and on-site work practices EN 1449-1996 塑料管道系统 玻璃纤维增强热固性塑料(GRP)组件 查检水泥套管插承办合设计的实验措施 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) components - Test methods to prove the desi

25、gn of cemented socket-and-spigot joints EN 1492-1- 织物吊索 安全性 第1部分：一般用途人造纤维扁平织物吊索 Textile slings - Safety - Part 1: Flat woven webbing slings, made of man-made fibres, for general purpose use EN 1492-2- 织物吊索 安全性 第2部分：一般用途人造纤维园吊索 Textile slings - Safety - Part 2: Roundslings, made of man-made fibres, f

26、or general purpose use EN 1636-3-1997 无压力排水和污水用塑料管道系统 不饱和聚脂树脂(UP) 基玻璃纤维增强热固性塑料(GRP) 第3部分：管件 Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 3: Fittings EN 1636-5-1997 无压力排水和污水用塑料管道系统 不饱和聚脂

27、树脂(UP) 基玻璃纤维增强热固性塑料(GRP) 第5部分：针对接头 Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 5: Fitness for purpose of the joints EN 1636-6-1997 无压力排水和污水用塑料管道系统 不饱和聚脂树脂(UP) 基玻璃纤维增强热固性塑料(GRP) 第6部分：安装

28、实践 Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 6: Practices for installation EN 1787- 食物 用ESR法检测含纤维素通过辐射的食品 Foodstuffs - Detection of irradiated food containing cellulose by ESR spectr

29、oscopy EN 1813-1997 铺地织物 用研磨机器对羊毛纤维完整性的测定 Textile floor coverings - Determination of wool fibre integrity using an abrasion machine EN 23-1-1978 洗涤粉和清洁粉的包装 纤维板硬纸盒和圆筒的尺寸和体积 Packages for washing and cleaning powders; dimensions and volumes of cartons and drums from fibre board EN 2329-1993 航空航天系列 纺织玻璃

30、纤维预浸渍树脂 测定单位面积质量的实验措施 Aerospace series - Textile glass fibre preimpregnates - Test method for the determination of mass per unita area EN 2330-1993 航空航天系列 纺织玻璃纤维预浸渍树脂 测定挥发物质含量的实验措施 Aerospace series - Textile glass fibre preimpregnates - Test method for the determination of the content of volatile ma

31、tter EN 2331-1993 航空航天系列 纺织玻璃纤维预浸渍树脂 测定单位面积树脂和纤维含量及纤维质量的实验措施 Aerospace series - Textile glass fibre preimpregnates - Test method for the determination of the resin and fibre content and mass of fibre per unit area EN 2332-1993 航空航天系列 纺织玻璃纤维预浸渍树脂 测定树脂流速的实验措施 Aerospace series - Textile glass fibre pre

32、impregnates - Test method for the determination of the resin flow EN 2374-1991 航空航天系列 玻璃纤维增强模压件和夹层复合件 实验板的制备 Aerospace series - Glass fibre reinforced mouldings and sandwich composites - Production of test panels EN 2377-1989 航空航天系列 玻璃纤维增强塑料 实验措施 表观层间剪切强度测定 Aerospace series - Glass fibre reinforced

33、plastics - Test method - Determination of apparent interlaminar shear strength EN 2378-1995 航空航天系列 纤维增强塑料 通过浸渍对吸水率的测定 Aerospace series - Fibre reinforced plastics - Determination of water absorption by immersion EN 2489-1995 航空航天系列 纤维增强塑料 实验液体影响的测定 Aerospace series - Fibre reinforced plastics - Dete

34、rmination of the action of test fluids EN 2557-1997 航空航天系列碳纤维预浸渍物单位面积质量的测定 Aerospace series - Carbon fibre preimpregnates - Determination of mass per unit area EN 2558-1997 航空航天系列碳纤维预浸渍物挥发物含量测定 Aerospace series - Carbon fibre preimpregnates - Determination of the volatile content EN 2559-1997 航空航天系列

35、碳纤维预浸渍物树脂成分树脂和纤维含量及单位面积纤维质量的测定 Aerospace series - Carbon fibre preimpregnates - Determination of the resin and fibre content and the mass of fibre per unit area EN 2561-1995 航空航天系列碳纤维增强塑料单向塑料层压制品纤维方向平行抗拉实验 Aerospace series - Carbon fibre reinforced plastics - Unidirectional laminates - Tensile test

36、parallel to the fibre direction EN 2562-1997 航空航天系列碳纤维增强塑料单向层压塑料与纤维方向平行的弯曲实验 Aerospace series - Carbon fibre reinforced plastics - Unidirectional laminates - Flexural test parallel to the fibre direction EN 2563-1997 航空航天系列碳纤维增强塑料单向层压板层间表面剪切强度的测定 Aerospace series - Carbon fibre reinforced plastics -

37、 Unidirectional laminates - Determination of the apparent interlaminar shear strength EN 2564-1998 航空航天系列碳纤维叠层板材纤维、树脂含量和空隙率的测定 Aerospace series - Carbon fibre laminates - Determination of the fibre, resin and void contents EN 2597-1998 航空航天系列碳纤维增强塑料单向叠层板材垂直于纤维方向的拉伸实验 Aerospace series - Carbon fibre

38、reinforced plastics - Unidirectional laminates - Tensile test perpendicular to the fibre direction EN 2743- 航空航天系列纤维增强塑料测试材料未老化前调理的原则程序 Aerospace series - Fibre reinforced plastics - Standard procedures for conditioning prior to testing unaged materials EN 2746-1998 航空航天系列玻璃纤维增强塑料弯曲实验三点弯曲法 Aerospace

39、 series - Glass fibre reinforced plastics - Flexural test - Three point bend method EN 2747-1998 航空航天系列玻璃纤维增强塑料抗拉实验 Aerospace series - Glass fibre reinforced plastics - Tensile test EN 300-1997 定向纤维板(OSB) 定义、分类和规范 Oriented Strand Boards (OSB) - Definitions, classification and specifications EN 302-3

40、-1992 承重木构造用胶粘剂 实验措施 第3部分：通过温度和湿度循环实验测定酸性腐蚀对木纤维横向拉伸强度的影响 Adhesives for load - Bearing timber structures - Test methods - Part 3: Determination of the effect of acid damage to wood fibres by temperature and humidity cycling on the transverse tensile strength EN 316-1999 木纤维板 定义、分类和符号 Wood fibreboards

41、 - Definition, classification and symbols EN 317-1993 碎料板和纤维板 在水中浸泡后膨胀厚度的测定 Particleboards and fibreboards; determination of swelling in thickness after immersion in water EN 319-1993 碎料板和纤维板 与板平面垂直的拉伸强度的测定 Particleboards and fibreboards; determination of tensile strength perpendicular to the plane

42、of the board EN 320-1993 纤维板 抗螺钉轴向拔出力的测定 Fibreboards - Determination of resistance to axial withdrawal of screws EN 382-1-1993 纤维板 表面吸取性测定 第1部分：干燥解决纤维板实验措施 Fibreboards - Determination of surface absorption - Part 1: Test method for dry process fibreboards EN 382-2-1993 纤维板 表面吸取性测定 第2部分：硬质板实验措施 Fibre

43、boards - Determination of surface absorption - Part 2: Test method for hardboards EN 40-7- 灯柱 第7部分：纤维增强聚合物灯柱规范 Lighting columns - Part 7: Requirements for fibre reinforced polymer composite lighting columns EN 492-1994+A1-1999+AC-1996 屋面用的纤维水泥条板及其配件 产品规范和实验措施 Fibre-cement slates and their fittings f

44、or roofing; product specification and test methods / Note: To be replaced by prEN 492 (-07). EN 494-1994+A1-1999+AC-1996 屋面用的纤维水泥型板及其配件 产品规范和实验措施 Fibre-cement profiled sheets and fittings for roofing; product specification and test methods / Note: To be replaced by prEN 494 (-07). EN 50053-3-1989 使用

45、易燃材料的静电喷涂器的选择、安装和使用规定第3部分：能量极限为0.24mJ 或5mJ的手持静电纤维填料喷 Requirements for the selection, installation and use of electrostatic spraying equipment for flammable materials - Part 3: Hand - held electrostatic flock spray guns with an energy limit of 0,24 mJ or 5 mJ and their associated apparatus EN 50353-

46、绝缘油通过显微镜记数法测定纤维污染 Insulating oil - Determination of fibre contamination by the counting method using a microscope EN 512-1994+A1- 纤维水泥制品 压力管道和接头 Fibre-cement products - Pressure pipes and joints EN 588-1-1996 污水管和排水管用纤维水泥管 第1部分：重力系统用管道、管连接件和管配件 Fibre-cement pipes for sewers and drains - Part 1: Pipe

47、s, joints and fittings for gravity systems EN 588-2- 污水管和排水管用纤维水泥管 第2部分：检修孔和检查室 Fibre cement pipes for drains and sewers - Part 2: Manholes and inspection chambers EN 59-1977 玻璃纤维增强塑料 用 Barcol压痕措施测量硬度 Glass reinforced plastics - Measurement of hardness by means of a Barcol impressor EN 60249-2-1-199

48、4+A2-1994+A3-1995+A4- 印制电路用基材第2-1部分：高电气质量的酚醛纤维素纸覆铜层压板 Base materials for printed circuits; part 2: specifications; specification No. 1: phenolic cellulose paper copper-clad laminated sheet, high electrical quality (IEC 60249-2-1:1985 + A1:1989) EN 60249-2-14-1994+A3-1994+A4-1995+A5- 印制电路用基材第2-14部分：规

49、范阻燃型酚醛纤维素纸覆铜层压板（垂直燃烧实验）经济型 Base materials for printed circuits; part 2: specifications; specification no. 14: phenolic cellulose paper copper-clad laminated sheet of defined flammability (vertical burning test), economic quality (IEC 60249-2-14:1988 + A2:1990) EN 60249-2-2-1994+A3-1994+A4-1995+A5- 印

50、制电路用基材第2-2部分：规范酚醛纤维素纸覆铜箔层压板经济型 Base materials for printed circuits; part 2: specifications; specification No. 2: phenolic cellulose paper copper-clad laminated sheet, economic quality (IEC 60249-2-2:1985 + A2:1990) EN 60249-2-3-1994+A2-1994+A3-1995+A4- 印制电路用基材第2-3部分：规范阻燃型环氧化物纤维素纸覆铜层压板（垂直燃烧实验） Base m

51、aterials for printed circuits; part 2: specifications; specification No. 3: epoxide cellulose paper copper-clad laminated sheet of defined flammability (vertical burning test) (IEC 60249-2-3:1987 + A1:1989) EN 60249-2-6-1994+A3-1994+A4-1995+A5- 印制电路用基材第2-6部分：规范阻燃型酚醛纤维素纸覆铜层压板（水平燃 烧实验） Base materials

52、for printed circuits; part 2: specifications; specification No. 6: phenolic cellulose paper copper-clad laminated sheet of defined flammability (horizontal burning test) (IEC 60249-2-6:1985 + A1:1989) EN 60249-2-7-1994+A3-1994+A4-1995+A5- 印制电路用基材第2-7部分：规范阻燃型酚醛纤维素纸覆铜层压板（垂直燃烧实验） Base materials for pri

53、nted circuits; part 2: specifications; specification No. 7: phenolic cellulose paper copper-clad laminated sheet of defined flammability (vertical burning test) (IEC 60249-2-7:1987 + A1:1989) EN 60249-2-9-1994+A3-1994+A4-1995+A5- 印制电路用基材第2-9部分：规范阻燃型环氧化物纤维素纸芯、环氧化物玻璃布表面覆铜层压板（垂直燃烧试 Base materials for p

54、rinted circuits; part 2: specifications; specification No. 9: epoxide cellulose paper core, epoxide glass cloth surfaces copper-clad laminated sheet of defined flammability (vertical burning test) (IEC 60249-2-9:1987 + A1:1989 + A2:19 EN 60454-3-10-1995 电工用压敏粘带 第3部分：单项材料规范 活页10：涂橡胶热固性粘合剂的乙酸丁酸纤维素薄膜胶粘

55、带的规定 Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials - Sheet 10: Requirements for cellulose-acetate-butyrate film tapes with rubber thermosetting adhesive (IEC 60454-3-10:1995) EN 60454-3-11-1998 电气用压敏胶粘带 第3部分：单项材料规范 活页11：涂橡胶热固性粘合剂的纤维素皱纹纸与聚

56、对苯二甲酸乙二 Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials - Sheet 11: Combined tapes made of creped cellulosic paper and polyethylene terephthalate film with rubber thermosetting adhesive (IEC 60454-3-11) EN 60454-3-13-1995 电工用压敏粘带 第3部分：单项材料规

57、范 活页13：一面涂覆热塑材料、另一面涂橡胶热固性粘合剂的复合纤维 Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials - Sheet 13: Requirements for combined cellulose-viscose woven fabric tapes, on side covered with a thermoplastic material, the other side with rub EN 60454-3-

58、4-1998 电气用压敏粘带 第3部分：单项材料规范 活页4：涂橡胶执固性粘合剂的纤维素皱纹纸 Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials - Sheet 4: Cellulosic paper, creped, with rubber thermosetting adhesive (IEC 60454-3-4:1998) EN 60454-3-5-1998 电气用压敏胶粘带 第3部分：单项材料规范 活页5：涂橡胶热固性粘合

59、剂的纤维素非皱纹纸 Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials - Sheet 5: Cellulosic paper, non-creped, with rubber thermosetting adhesive (IEC 60454-3-5:1998) EN 60454-3-9-1998 电气用压敏感胶粘带 第3部分：单项材料规范 活页9：涂橡胶热固性粘合剂的醋酯纤维素织布带 Pressure-sensitive adh

60、esive tapes for electrical purposes - Part 3: Specifications for individual materials - Sheet 9: Cellulose acetate woven fabric tapes with rubber thermosetting adhesive (IEC 60454-3-9:1998) EN 60554-2- 电学用的纤维纸第2部分：实验措施 Cellulosic papers for electrical purposes - Part 2: Methods of test (IEC 60554-2:

61、) EN 60601-2-4- 医疗电气设备第2-4部分：心脏除纤维颤抖器安全性的特殊规定 Medical electrical equipment - Part 2-4: Particular requirements for the safety of cardiac defibrillators (IEC 60601-2-4:) / Note: Endorsement notice EN 60684-3-300- 绝缘软套管第3部分：多种型号套管规范活页300：无涂层的玻璃纤维编织套管 Flexible insulating sleeving - Part 3: Specificatio

62、ns for individual types of sleeving; Sheet 300: Glass textile fibre sleeving, braided, uncoated (IEC 60684-3-300:) / Note: Endorsement notice EN 60684-3-400 bis 402- 绝缘软套管第3部分：多种型号套管规范活页400至402：有硅橡胶涂层的玻璃纤维纺织套管 Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving; Sh

63、eets 400 to 402: Glass textile sleeving with silicone elastomer coating (IEC 60684-3-400 to 402:) / Note: Endorsement notice EN 60684-3-403 bis 405- 绝缘软套管第3部分：多种型号套管规范活页403-405：丙烯酸脂玻璃纤维编织套管 Flexible insulating sleeving - Part 3: Specification for individual types of sleeving; Sheets 403 to 405: Glas

64、s textile sleeving with acrylic based coating (IEC 60684-3-403 to 405:) / Note: Endorsement notice EN 60684-3-406 bis 408- 绝缘软套管第3部分：多种型号套管规范活页406-408：有PVC涂层的玻璃纤维纺织套管 Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving; Sheets 406 to 408: Glass textile sleeving with PVC