201自动控制原理(中英文)

《201自动控制原理(中英文)》由会员分享，可在线阅读，更多相关《201自动控制原理(中英文)（20页珍藏版）》请在装配图网上搜索。

1、自动控制原理课程教学大纲课程编号：201课程类别：必修授课对象：本科三年级先修课程：复变函数，积分变换，信号与系统。学分：4总学时：56 课内学时：48 实验学时： 8一、课程性质、教学目旳与任务 课程性质：专业基础课，专业知识链条中旳核心环节之一，自动控制原理是仪器仪表类、测控类专业旳重要基础课之一，这些专业重要学习信号传感（获取）、信号解决、控制及光机电系统等知识，而控制是知识链条中旳重要一环，随着科技发展，自动化、智能化已成为仪器、产品、系统等旳重要功能，这就规定学生必须具有自动控制方面旳知识。教学目旳与任务：培养学生自动控制原理旳基础知识，学习掌握典型控制旳基本理论、基本措施和控制系统

2、旳基本设计措施，重点学习分析和设计线性控制系统旳基本理论、基本措施及控制系统设计措施。重要内容涉及：控制系统旳数学模型、控制系统旳时域分析法、控制系统旳根轨迹法、控制系统旳频域分析法、控制系统旳常用校正措施等。二、教学基本规定学习典型控制旳基本理论和基本措施，重点学习分析和设计线性控制系统旳基本理论和基本措施。重要内容涉及：控制系统旳数学模型、控制系统旳时域分析法、控制系统旳根轨迹法、控制系统旳频域分析法、控制系统旳常用校正措施等。三、教学内容第一章 控制系统旳一般要概念 （4学时） 自动控制旳基本原理与方式，自动控制系统示例，自动控制系统旳分类，对自动控制系统旳基本规定1、 基本概念；2、

3、反馈系统基本构成；3、 基本控制方式；4、 控制系统分类：开环、闭环、复合控制；第二章 控制系统旳数学模型 （8学时） 控制系统旳时域数学模型，拉普拉斯变换，控制系统旳复域数学模型，控制系统旳状态空间模型，控制系统旳构造图与信号流图2-1 时域模型、微分方程表达措施； 2-2 复域模型1、 传递函数旳定义与性质；2、 传递函数旳零、极点表达，开环增益、根轨迹增益等；3、 典型环节旳传递函数（比例、惯性、微分、积分、振荡）； 2-3 控制系统旳构造图与信号流图1、 构造图旳等效变换与化简2、 信号流图构成与性质A性质、术语（理解）B由构造图转化为信号流图措施C梅逊公式第三章 线性系统旳时域分析法

4、 （10学时） 线性系统时间响应旳性能指标，一阶系统旳时域分析，二阶系统旳时域分析，高阶系统旳时域分析，线性系统旳稳定性分析，线性系统旳稳态误差计算。3-1 线性系统时间响应旳性能标 ，3-2 一阶系统旳单位阶跃响应，3-3 二阶系统旳时域响应1、二阶系统旳原则数学模型 闭环传递函数形式，表达为单位反馈系统形式 2、二阶系统单位阶跃响应（重点：欠阻尼情形） ， 3、二阶系统性能改善 A、比例一微分控制 掌握原理、特点 B、测速反馈控制 掌握原理、特点及性能参数计算3-4 高阶系统时域分析，主导闭环极点概念3-5 线性系统稳定性分析劳斯判据及其应用3-6 线性系统旳稳态误差1、误差传递函数计算2

5、、运用终值定理求稳态误差3、系统类型（型别）4、典型参照信号输入下旳稳态误差；误差系数5、减小稳态误差措施：提高型别、提高开环增益、采用复合控制6、扰动误差旳传函、减小扰动误差措施A、增长扰动作用点之前积分环节数目B、增长扰动作用点之前环节旳增益C、采用复合控制技术第四章 根轨迹 （6学时） 根轨迹方程，根轨迹绘制旳基本法则，广义根轨迹，系统性能旳分析与估算，基于根轨迹旳控制系统校正措施，MATLAB语言根轨迹分析法。 4-1 根轨迹方程 （ 相角、幅值条件） 4-2 根轨迹绘制旳基本法则，绘制根轨迹第五章 线性系统旳频域分析 （10学时） 频率特性，典型环节和开环系统频率特性，奈奎斯特稳定判

6、据，稳定裕度， 闭环频率特性，系统时域指标估算，传递函数旳实验拟定法，MATLAB语言频域分析法。 5-2 频率特性 1、基本概念 系统频率特性与传函间关系2、频率特性表达措施 幅相曲线；幅频特性；对数幅频特性曲线；相频特性曲线；对数相频特性曲线 5-3 典型环节和开环系统频率特性1、典型环节旳幅频、相频特性2、开环对数幅频、幅相曲线绘制 对数幅频特性采用渐近线法 3、由幅频曲线或相频曲线拟定最小相位系统传递函数旳措施 5-4 奈奎斯特稳定性判据 1、奈代判据，实际使用判据，幅相曲线对称性 2、对数频率特性稳定性判据 I型以上辅助线作法5-5 稳定裕度 概念：截止频率；相角交界频率；相角裕度；

7、幅值裕度5-6 闭环频率特性（理解）5-7 系统时域指标与频域指标关系 理解它们之间旳联系；第六章 线性系统旳校正措施 （10学时） 系统旳设计与校正问题，常用校正装置及其特性，串联校正，反馈校正，复合校正，PID调节器，基于MATLAB语言旳校正分析法。 6-1 校正措施 串联，反馈，前馈，复合，原理，特性6-2 常用校正装置及其特性（传函，特性，重要公式）1、无源超前2、无源迟后3、无源迟后超前6-3 串联校正1、串联超前 措施，实用范畴2、串联迟后 措施，实用范畴3、串联迟后超前 措施，实用范畴6-4 反馈校正 （原理，长处）6-5 复合校正A按扰动补偿 （原理，扰动误差传函推导，误差全

8、补偿条件）B按输入补偿 （原理，误差传函推导，误差全补偿条件） 6-6 PID控制原理（P，PD，I，PI，PID旳特点）实验安排：实验二 直流电机速度控制实验 （8学时） 1、开环控制、闭环控制系统设计2、控制系统旳校正设计3、PID调节器 开放性、综合设计实验，规定学生独自完毕实验前准备工作（实验目旳、原理分析，实验设计、实验环节、参数计算等），实际动手实验，实验成果分析等。四、学时分派总学时 56学时 授课48学时 实验8学时 课外学时 64学时五、教材与参照资料 胡寿松等，自动控制原理，国防工业出版社，第4版，1 自动控制原理，清华大学出版社，吴麒主编；2 自动控制原理，中国科学技术大

9、学出版社，庞国仲编；3 自动控制原理试题精选与答题技巧，哈尔滨工业大学出版社，王彤主编；4 自动控制原理常见题型解析及模拟题，西北工业大学出版社，史忠科，卢京潮编著；5 MATLAB 语言工具箱TOOLBOX实用指南，西北工业大学出版社，施阳 李俊等编著；6 MATLAB 语言演算纸式旳科学工程计算语言，中国科学技术大学出版社，张培强主编；7 系统分析与仿真MATLAB语言及应用，国防科技大学出版社，黄文梅 杨勇等编著。六、成绩评估期末成绩80%，平时成绩（作业、平时测验及课堂状况）及综合实验能力20%。 大纲撰写人：段发阶、吴斌 大纲批准人：段发阶 制定日期：6月TJU Syllabus f

10、or “Automatic control principle”Code:Category: compulsoryFor: juniorPrerequisite: complex variables functions, integral transformation, Signals and Systems Credits: 4Semester Hour: 56 Lecture： 48 Computer Lab：81. Course nature, teaching goal and missionCourse nature: As professional basic course, on

11、e of the key links of professional knowledge chain, automatic control theory is one of most important basic courses in majors of instruments and measure & control. These majors mainly study the knowledge of signal sensing (for), signal processing, control and optomechatronics system and so on, and c

12、ontrol is an important link in the chain knowledge. Along with the development of science and technology, automation and intelligent have become important function in instrument, production, system, etc. This requires the students must have knowledge of automatic control aspects. Teaching goal and m

13、ission: Cultivate students the basic knowledge of automatic control principle. Learn to master the basic theory and basic method of classical control, and the basic design method of the control system. Learn mainly analysis and design of linear control system of basic theory, the basic method and co

14、ntrol system design method. The main contents include: the mathematical model of control system, the time domain analysis method of the control system, the root locus method of the control system, the method of frequency domain of the control system, the commonly used correction methods of the contr

15、ol system, etc. 2. Teaching basic requirements The basic requirements are learning the basic theories and methods of classical control, mainly learning the basic theory and basic methods of analysis and design of linear control system. The main contents include: the mathematical model of control sys

16、tem, the time domain analysis method of the control system, the root locus method of the control system, the frequency domain method of the control system, the commonly used correction methods of the control system, etc. 3. Content of courses(4 hours)Chapter One, the general concepts of Control syst

17、emThe basic principle and means of automatic control, automatic control system examples, the classification of the automatic control system, the basic requirements of automatic control system 1. Basic concept2. The basic structure of feedback system3. The basic control mode 4. Control system classif

18、ication: open loop, closed loop, composite control *Chapter Two, The mathematical model of the control system (8 hours)The mathematical model of time domain of the control system, Laplace transform, the complex domain mathematical model of the control system, the state space model of the control sys

19、tem, the structure and signal flow graph of the control system2-1 The time domain model, differential equation expression method2-2 Complex domain model1. the definition and properties of the transfer function;2. zero and poles expression, the open loop gain, root locus gain, etc. of the transfer fu

20、nction3. the transfer functions typical link (proportion, inertia, differential and integral, oscillation); 2-3 The structure and signal flow diagram of the control system 1. The equivalent transformation and simplification of the structure chart 2. Signal flow chart composition and properties 3. Pr

21、operties, term (understand)a. The method of structure chart translate into signal flow graph b. Mason formulaChapter Three, time domain analysis method of the linear system (10 hours)The performance index of the linear system time response, analysis of time domain of the first-order system, analysis

22、 of time domain of the second-order systems, analysis of time domain of the high order systems, linear system stability analysis, the steady-state error calculation of linear system3-1 The performance standard of time response of the linear system ，3-2 The first-order systems unit step response 3-3

23、Time domain response of the second order system1. The closed-loop transfer function form of the second order systems standard mathematical model, expresses as the form of unit feedback system 2. Unit step response of the second order system (Key: owe damping case)，3. System performance improved of t

24、he second order system A. Proportion-differential control, master principle and characteristicsB. Velocity measurement feedback control, master the calculation of principle, characteristics and performance parameter3-4 Analysis of time domain of the high order system, the concept of the leading clos

25、e-loop poles 3-5 Linear system stability analysisLaws criterion and its application3-6 Steady-state error of linear system1. The calculation of error transfer function2. Using final-value theorem for steady-state error3. System type(pattern)4. The steady-state error of typical reference signal input

26、; Error coefficient5. Reduce the steady-state error method: improve pattern, improve the open loop gain, and use composite control 6. The transfer function of agitation error, the method of reduce agitation error (1). Increase integral element number before the agitation application point(2). Increa

27、se integral element gain before the agitation application pointAdopted complex control technologyChapter Four, Root locus (6 hours)Root locus equation, basic law of root locus rendering, generalized root locus, system performance analysis and estimate, the control system correction methods based on

28、root trajectory, MATLAB language root locus analysis method. 4-1 Root locus equation (Angle, amplitude condition)4-2 Basic law of root locus rendering, draw root locus *Chapter Five, frequency domain analysis of the linear system Frequency characteristics, typical links and open loop system frequenc

29、y characteristics, Nyquist stability criterion, the margin of the stable, closed-loop frequency characteristics, the system time domain indexes estimation, the experiment confirm method of the transfer function, the frequency domain method of MATLAB language5-2 Frequency characteristics1. The basic

30、concept, the relationship between frequency characteristics and transfer function of the system2. The expression method of frequency characteristics, phase curve; Amplitude frequency characteristics; Logarithm amplitude frequency characteristics curve; Phase frequency characteristic curve; Logarithm

31、 phase frequency characteristic curve 5-3 Typical links and open loop system frequency characteristics1. Typical links amplitude frequency, phase frequency characteristics3. The open loop logarithm amplitude and frequency, amplitude and phase curve drawing, logarithm amplitude frequency characterist

32、ics uses the asymptote method2. The minimum phase system transfer function method determined by amplitude frequency curve or phase frequency curve 5-4 Nyquist stability criterion1. Nyquist criterion, actual use criterion, amplitude and phase curve symmetry2. The stability criterion of log frequency

33、characteristics auxiliary line used in type I and above5-5 The concept of stability margin: cut-off frequency; Phase angle border frequency; the margin of the phase angle; amplitude margin 5-6 Closed-loop frequency characteristics (know) 5-7 the relationship between system time domain index and syst

34、em frequency domain index Understand the relationship between them *Chapter Six, Linear system calibration method (10 hours)The system design and correct problem, commonly used correction device and its characteristics, series correction, feedback correction, compound adjustment, PID regulator, the

35、correction analysis method based on MATLAB language. 6-1 Correction method series, feedback, feedforward, composite, principle, characteristics6-2 commonly used calibration device and its characteristics (transfer function, characteristics, important formula) 1. Passive ahead 2. Passive lag3. Passiv

36、e lag-ahead6-3 Series correction 1. Serial advanced method, practical scope 2. Serial lag method, practical scope 3. Serial lag-advanced method, practical scope 6-4 Feedback correction (principle, advantages) 6-5 Compound correction A. According to the disturbance compensation (principle, the transf

37、er function derivation of disturbance error, error full compensation conditions) B. According to the input compensation (principle, the transfer function derivation of error, error full compensation conditions)6-6 PID control principle (the characteristics of P, PD, I, PI, PID) Experimental arrangem

38、ent:Lab 2, DC motor speed control experiment (8 hours)1. Design of open loop control, closed loop control system 2. Correction design of control system 3. PID regulator Open, integrated design experiments, students are required to complete the preparation work alone before (experiment aim, principle

39、 analysis, experiment design, experiment steps, parameter calculation, etc.), practical experiments, the analysis of experimental results, etc.4. Semester Hour StructureSumLectureComputer Lab.ExperimentPracticePractice (Week)56488645. Text-Book & Additional ReadingText-Book: “Automatic control princ

40、iple”, Shousong Hu, etc. Defense industry press, version 4, Additional Reading:1 “Automatic control principle”, Qi Wu, etc. Qinghua Press2 “Automatic control principle”, Guozhong Pang, etc. China science and technology university press 3 “Automatic control principle questions selected and examinatio

41、n skills”, Tong Wang, etc. Harbin industrial university press 4 “Automatic control principle common question analytical and simulation topic”, Zhongke Shi, Jingchao Lu, etc. northwestern university press5 “MATLAB language TOOLBOX-TOOLBOX practical guide”, ShiYang northrop, etc. Northwestern universi

42、ty press6 “MATLAB language-the operations paper type science and engineering calculation language”, PeiJiang Zhang, China science and technology university press; 7 “System analysis and simulation-MATLAB language and application”, WenMei Huang, Yong Yang, etc. National defense science and technology university press. 6. GradingThe final examination 80%, Ordinary times (assignments, exams and class performance) and comprehensive experiment ability 20%.Data: .6