角钢钢材检测报告
《角钢钢材检测报告》由会员分享,可在线阅读,更多相关《角钢钢材检测报告(23页珍藏版)》请在装配图网上搜索。
1、 WORD格式 编辑整理 钢材检测报告Steel Test Report样品名称 角钢 建设单位 无锡明阗通用设备制造 报告编号 B00042170900831a Sample name: Angle steel Construction unit: Wuxi Mingtian General Equipment Manufacturing Co., Ltd Report number: B00042170900831a 委托单位 无锡明阗通用设备制造 施工单位 - 检测类别 委托检测 Client: Wuxi Mingtian General Equipment Manufacturing
2、Co., Ltd Construction unit: Test category: Entrusted Test工程名称 JMR2x60t/h燃煤锅炉工程 监理单位 - 样品状态 可检 Project name : JMR2x60t/h coal-fired boiler project Supervision unit: Sample status: Detectable 检测依据 GB/T706-2008热轧型钢 检测环境 20OC 检测日期 2012-11-28 Test Standard: GB/T706-2008 hot-rolled steel section Testing e
3、nvironment: 20OC Inspection date: November 28, 2012表1 化学成分Table1. Chemical composition牌号Marks化 学 成 分 %Chemical compositions %CMnSiPS检测结论 Test conclusionQ235B0.160.480.290.0400.025该样品经检验,按GB/T706-2008标准评定:化学成分分析合格After the sample inspection, the analysis of chemical composition is acceptable in accor
4、dance with GB/T706-2008 Standard.牌号Marks规格Specification(mm)计算重量Calculated weight(t)拉伸弯曲试验Bending Test(180O)代表数量Representative quantity(t)生产厂家Manufacturer质保书编号Warranty number构造部位Sructural part检测结论Test conclusion屈服点sYield points(MPa)抗拉强度bTensile Strengthb(MPa)伸长率5Elongation5(%)Q235BL50502.52704203227.
5、52.5马鞍山钢铁股份Maanshan Iron & Steel Co., LtdZ23060950005烟风道Flue and air duct该样品经检验,按GB/T706-2008标准评定:机械性能合格After the sample inspection, mechanical properties are acceptable in accordance with GB/T706-2008 Standard.表2 机械性能 Table 2. Mechanical properties检测报告说明:1.假设对报告有异议,应于收到报告之日期起十五日内,以书面形式向检测单位提出,逾期视为对
6、报告无异议。 2.送样检测,检测结果仅对来样负责。 3.报告及其复印件未加盖本单位检测报告专用章,报告无效。Notes for test report: 1. In case of test discrepancy, objections should be filed within 15 days after the receipt of the test report, meanwhile, the objections shall be submitted in written form to the inspection unit, otherwise overdue objectio
7、ns shall be waived. 2. For entrusted tests, the test results presented in this report relate only to the samples delivered. 3. This report and the copies of it are not valid unless stamped by the inspection unit. 检测单位:无锡市建筑工程质量检测中心 Test unit: Wuxi Inspection Center for Construction Quality负责人: 审核人:
8、试验人: 单位地址:江苏省无锡市新区新辉环路8号 Address: No. 8 Xinhui Ring Road, Wuxi New District, Jiangsu Director Reviewer: Tester: 报告日期: 2012-11-28 Report date: November 28, 2012上岗证号: B0035 B0322 B0377 电 话: 0510-88156786, :0510-88156786 Telephone: 0510-88156786 Fax No.:0510-88156786Certificate No. B0035 B0322 B0377 邮
9、编: 214028 Zip Code: 214028钢材检测报告Steel Test Report样品名称 角钢 建设单位 无锡明阗通用设备制造 报告编号 B00042170900832a Sample name: Angle steel Construction unit: Wuxi Mingtian General Equipment Manufacturing Co., Ltd Report number: B00042170900832a 委托单位 无锡明阗通用设备制造 施工单位 - 检测类别 委托检测 Client: Wuxi Mingtian General Equipment M
10、anufacturing Co., Ltd Construction unit: Test category: Entrusted Test工程名称 JMR2x60t/h燃煤锅炉工程 监理单位 - 样品状态 可检 Project name : JMR2x60t/h coal-fired boiler project Supervision unit: Sample status: Detectable 检测依据 GB/T706-2008热轧型钢 检测环境 20OC 检测日期 2012-11-28 Test Standard: GB/T706-2008 hot-rolled steel sect
11、ion Testing environment: 20OC Inspection date: November 28, 2012表1 化学成分Table1. Chemical composition牌号Marks化 学 成 分 %Chemical compositions %CMnSiPS检测结论Test conclusionQ235B0.130.550.230.0300.020该样品经检验,按GB/T706-2008标准评定:化学成分分析合格After the sample inspection, the analysis of chemical composition is accepta
12、ble in accordance with GB/T706-2008 Standard.牌号Marks规格Specification(mm)计算重量Calculated weight(t)拉伸弯曲试验Bending Test(180O)代表数量Representative quantity(t)生产厂家Manufacturer质保书编号Warranty number构造部位Sructural part检测结论Test conclusion屈服点sYield points(MPa)抗拉强度bTensile Strengthb(MPa)伸长率5Elongation5(%)Q235BL8083.2
13、2854352927.52.5马鞍山钢铁股份Maanshan Iron & Steel Co., Ltd09041256煤斗Coal hopper该样品经检验,按GB/T706-2008标准评定:机械性能合格After the sample inspection, mechanical properties are acceptable in accordance with GB/T706-2008 Standard.表2 机械性能 Table 2. Mechanical properties检测报告说明:1.假设对报告有异议,应于收到报告之日期起十五日内,以书面形式向检测单位提出,逾期视为对
14、报告无异议。 2.送样检测,检测结果仅对来样负责。 3.报告及其复印件未加盖本单位检测报告专用章,报告无效。Notes for test report: 1. In case of test discrepancy, objections should be filed within 15 days after the receipt of the test report, meanwhile, the objections shall be submitted in written form to the inspection unit, otherwise overdue objectio
15、ns shall be waived. 2. For entrusted tests, the test results presented in this report relate only to the samples delivered. 3. This report and the copies of it are not valid unless stamped by the inspection unit. 检测单位:无锡市建筑工程质量检测中心 Test unit: Wuxi Inspection Center for Construction Quality负责人: 审核人:
16、试验人: 单位地址:江苏省无锡市新区新辉环路8号 Address: No. 8 Xinhui Ring Road, Wuxi New District, Jiangsu Director Reviewer: Tester: 报告日期: 2012-11-28 Report date: November 28, 2012上岗证号: B0035 B0322 B0377 电 话: 0510-88156786, :0510-88156786 Telephone: 0510-88156786 Fax No.:0510-88156786Certificate No. B0035 B0322 B0377 邮
17、编: 214028 Zip Code: 214028钢材检测报告Steel Test Report样品名称 角钢 建设单位 无锡明阗通用设备制造 报告编号 B00042170900833a Sample name: Angle steel Construction unit: Wuxi Mingtian General Equipment Manufacturing Co., Ltd Report number: B00042170900833a 委托单位 无锡明阗通用设备制造 施工单位 - 检测类别 委托检测 Client: Wuxi Mingtian General Equipment M
18、anufacturing Co., Ltd Construction unit: Test category: Entrusted Test工程名称 JMR2x60t/h燃煤锅炉工程 监理单位 - 样品状态 可检 Project name : JMR2x60t/h coal-fired boiler project Supervision unit: Sample status: Detectable 检测依据 GB/T706-2008热轧型钢 检测环境 20OC 检测日期 2012-11-28 Test Standard: GB/T706-2008 hot-rolled steel sect
19、ion Testing environment: 20OC Inspection date: November 28, 2012表1 化学成分Table1. Chemical composition牌号Marks化 学 成 分 %Chemical compositions %CMnSiPS检测结论Test conclusionQ235B0.190.500.290.0400.028该样品经检验,按GB/T706-2008标准评定:化学成分分析合格After the sample inspection, the analysis of chemical composition is accepta
20、ble in accordance with GB/T706-2008 Standard.牌号Marks规格Specification(mm)计算重量Calculated weight(t)拉伸弯曲试验Bending Test(180O)代表数量Representative quantity(t)生产厂家Manufacturer质保书编号Warranty number构造部位Sructural part检测结论Test conclusion屈服点sYield points(MPa)抗拉强度bTensile Strengthb(MPa)伸长率5Elongation5(%)Q235BL6361.8
21、2553702727.51.8马鞍山钢铁股份Maanshan Iron & Steel Co., LtdZ33060940301灰库渣库Ash and slag silo该样品经检验,按GB/T706-2008标准评定:机械性能合格After the sample inspection, mechanical properties are acceptable in accordance with GB/T706-2008 Standard.表2 机械性能 Table 2. Mechanical properties检测报告说明:1.假设对报告有异议,应于收到报告之日期起十五日内,以书面形式向
22、检测单位提出,逾期视为对报告无异议。 2.送样检测,检测结果仅对来样负责。 3.报告及其复印件未加盖本单位检测报告专用章,报告无效。Notes for test report: 1. In case of test discrepancy, objections should be filed within 15 days after the receipt of the test report, meanwhile, the objections shall be submitted in written form to the inspection unit, otherwise over
23、due objections shall be waived. 2. For entrusted tests, the test results presented in this report relate only to the samples delivered. 3. This report and the copies of it are not valid unless stamped by the inspection unit. 检测单位:无锡市建筑工程质量检测中心 Test unit: Wuxi Inspection Center for Construction Quali
24、ty负责人: 审核人: 试验人: 单位地址:江苏省无锡市新区新辉环路8号 Address: No. 8 Xinhui Ring Road, Wuxi New District, Jiangsu Director Reviewer: Tester: 报告日期: 2012-11-28 Report date: November 28, 2012上岗证号: B0035 B0322 B0377 电 话: 0510-88156786, :0510-88156786 Telephone: 0510-88156786 Fax No.:0510-88156786Certificate No. B0035 B0
25、322 B0377 邮 编: 214028 Zip Code: 214028钢材检测报告Steel Test Report样品名称 角钢 建设单位 无锡明阗通用设备制造 报告编号 B00042170900834a Sample name: Angle steel Construction unit: Wuxi Mingtian General Equipment Manufacturing Co., Ltd Report number: B00042170900834a 委托单位 无锡明阗通用设备制造 施工单位 - 检测类别 委托检测 Client: Wuxi Mingtian General
26、 Equipment Manufacturing Co., Ltd Construction unit: Test category: Entrusted Test工程名称 JMR2x60t/h燃煤锅炉工程 监理单位 - 样品状态 可检 Project name : JMR2x60t/h coal-fired boiler project Supervision unit: Sample status: Detectable 检测依据 GB/T706-2008热轧型钢 检测环境 20OC 检测日期 2012-11-28 Test Standard: GB/T706-2008 hot-rolle
27、d steel section Testing environment: 20OC Inspection date: November 28, 2012表1 化学成分Table1. Chemical composition牌号Marks化 学 成 分 %Chemical compositions %CMnSiPS检测结论Test conclusionQ235B0.170.430.210.0400.038该样品经检验,按GB/T706-2008标准评定:化学成分分析合格After the sample inspection, the analysis of chemical compositio
28、n is acceptable in accordance with GB/T706-2008 Standard.牌号Marks规格Specification(mm)计算重量Calculated weight(t)拉伸弯曲试验Bending Test(180O)代表数量Representative quantity(t)生产厂家Manufacturer质保书编号Warranty number构造部位Sructural part检测结论Test conclusion屈服点sYield points(MPa)抗拉强度bTensile Strengthb(MPa)伸长率5Elongation5(%)
29、Q235B10a36a3.531044531303.5马鞍山钢铁股份Maanshan Iron & Steel Co., LtdZ23070951014灰库渣库Ash and slag silo该样品经检验,按GB/T706-2008标准评定:机械性能合格After the sample inspection, mechanical properties are acceptable in accordance with GB/T706-2008 Standard.表2 机械性能 Table 2. Mechanical properties检测报告说明:1.假设对报告有异议,应于收到报告之日期
30、起十五日内,以书面形式向检测单位提出,逾期视为对报告无异议。 2.送样检测,检测结果仅对来样负责。 3.报告及其复印件未加盖本单位检测报告专用章,报告无效。Notes for test report: 1. In case of test discrepancy, objections should be filed within 15 days after the receipt of the test report, meanwhile, the objections shall be submitted in written form to the inspection unit, ot
31、herwise overdue objections shall be waived. 2. For entrusted tests, the test results presented in this report relate only to the samples delivered. 3. This report and the copies of it are not valid unless stamped by the inspection unit. 检测单位:无锡市建筑工程质量检测中心 Test unit: Wuxi Inspection Center for Constr
32、uction Quality负责人: 审核人: 试验人: 单位地址:江苏省无锡市新区新辉环路8号 Address: No. 8 Xinhui Ring Road, Wuxi New District, Jiangsu Director Reviewer: Tester: 报告日期: 2012-11-28 Report date: November 28, 2012上岗证号: B0035 B0322 B0377 电 话: 0510-88156786, :0510-88156786 Telephone: 0510-88156786 Fax No.:0510-88156786Certificate
33、No. B0035 B0322 B0377 邮 编: 214028 Zip Code: 214028钢材检测报告Steel Test Report样品名称 角钢 建设单位 无锡明阗通用设备制造 报告编号 B00042170900835a Sample name: Angle steel Construction unit: Wuxi Mingtian General Equipment Manufacturing Co., Ltd Report number: B00042170900835a 委托单位 无锡明阗通用设备制造 施工单位 - 检测类别 委托检测 Client: Wuxi Ming
34、tian General Equipment Manufacturing Co., Ltd Construction unit: Test category: Entrusted Test工程名称 JMR2x60t/h燃煤锅炉工程 监理单位 - 样品状态 可检 Project name : JMR2x60t/h coal-fired boiler project Supervision unit: Sample status: Detectable 检测依据 GB/T706-2008热轧型钢 检测环境 20OC 检测日期 2012-11-28 Test Standard: GB/T706-20
35、08 hot-rolled steel section Testing environment: 20OC Inspection date: November 28, 2012表1 化学成分Table1. Chemical composition牌号Marks化 学 成 分 %Chemical compositions %CMnSiPS检测结论Test conclusionQ235B0.190.400.180.0250.020该样品经检验,按GB/T706-2008标准评定:化学成分分析合格After the sample inspection, the analysis of chemica
36、l composition is acceptable in accordance with GB/T706-2008 Standard.牌号Marks规格Specification(mm)计算重量Calculated weight(t)拉伸弯曲试验Bending Test(180O)代表数量Representative quantity(t)生产厂家Manufacturer质保书编号Warranty number构造部位Sructural part检测结论Test conclusion屈服点sYield points(MPa)抗拉强度bTensile Strengthb(MPa)伸长率5El
37、ongation5(%)Q235B3.7515104.7515107.7515109.7515101.230541034271.2日照钢铁股份Rizhao Iron & Steel Co., Ltd0001901烟风道Flue and air duct灰库渣库Ash and slag silo该样品经检验,按GB/T706-2008标准评定:机械性能合格After the sample inspection, mechanical properties are acceptable in accordance with GB/T706-2008 Standard.表2 机械性能 Table 2
38、. Mechanical properties检测报告说明:1.假设对报告有异议,应于收到报告之日期起十五日内,以书面形式向检测单位提出,逾期视为对报告无异议。 2.送样检测,检测结果仅对来样负责。 3.报告及其复印件未加盖本单位检测报告专用章,报告无效。Notes for test report: 1. In case of test discrepancy, objections should be filed within 15 days after the receipt of the test report, meanwhile, the objections shall be su
39、bmitted in written form to the inspection unit, otherwise overdue objections shall be waived. 2. For entrusted tests, the test results presented in this report relate only to the samples delivered. 3. This report and the copies of it are not valid unless stamped by the inspection unit. 检测单位:无锡市建筑工程质
40、量检测中心 Test unit: Wuxi Inspection Center for Construction Quality负责人: 审核人: 试验人: 单位地址:江苏省无锡市新区新辉环路8号 Address: No. 8 Xinhui Ring Road, Wuxi New District, Jiangsu Director Reviewer: Tester: 报告日期: 2012-11-28 Report date: November 28, 2012上岗证号: B0035 B0322 B0377 电 话: 0510-88156786, :0510-88156786 Telephon
41、e: 0510-88156786 Fax No.:0510-88156786Certificate No. B0035 B0322 B0377 邮 编: 214028 Zip Code: 214028钢材检测报告Steel Test Report样品名称 角钢 建设单位 无锡明阗通用设备制造 报告编号 B00042170900836a Sample name: Angle steel Construction unit: Wuxi Mingtian General Equipment Manufacturing Co., Ltd Report number: B00042170900836a
42、委托单位 无锡明阗通用设备制造 施工单位 - 检测类别 委托检测 Client: Wuxi Mingtian General Equipment Manufacturing Co., Ltd Construction unit: Test category: Entrusted Test工程名称 JMR2x60t/h燃煤锅炉工程 监理单位 - 样品状态 可检 Project name : JMR2x60t/h coal-fired boiler project Supervision unit: Sample status: Detectable 检测依据 GB/T706-2008热轧型钢 检测环境 20OC 检测日期 2012-11-28 Test Standard: GB/T706-20
- 温馨提示:
1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 装配图网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。