交流伺服电机的驱动技术

上传人:wuxin****2020 文档编号:101605473 上传时间:2022-06-05 格式:DOC 页数:2 大小:36.01KB
收藏 版权申诉 举报 下载
交流伺服电机的驱动技术_第1页
第1页 / 共2页
交流伺服电机的驱动技术_第2页
第2页 / 共2页
资源描述:

《交流伺服电机的驱动技术》由会员分享,可在线阅读,更多相关《交流伺服电机的驱动技术(2页珍藏版)》请在装配图网上搜索。

1、交流伺服电机的驱动技术The amplifier for AC three-phase motors includes a pulse-width modulation circuit for voltage, current, and frequency control. Figure 11-81 shows an example of this type of amplifier. From the diagram you can see that this circuit is designed specifically for a three-phase trapezoidal mot

2、or. The transistors in the amplifier are connected in an H-bridge configuration. The motor windings are connected as a three-phase wye with no external wires connected to the wye point. This type of motor is also called a star connection when it is used with brushless AC servomotors. The drive logic

3、 and PWM switching controller is shown in the diagram as a block that is identified as a logic and PWM circuit. This block shows six arrows pointing away from it and pointing to the transistors. These arrows represent the six circuits for the base of each of the six transistors. The block below the

4、PWM circuit represents the current-sensing part of the amplifier. This section of the amplifier uses a recirculating chopper system to control the current in a manner that is similar to the chopper circuit in the DC amplifier. The signals for this section of the amplifier come from the voltage that

5、is developed across the series resistors connected between the transistor section and the motors. As you know, the amount of current flowing to the motor will determine the amount of voltage drop across these resistors.This amplifier has a velocity amplifier that receives the original command signal

6、 for the amplifier and the velocity feedback. The op amp provides an output that represents the difference (error) between the command signal and the feedback signal. The output of the velocity amp is sent to the torque amp, where it is combined with the feedback from the current-sensing block. The

7、output from this op amp is sent to the logic and PWM circuit block where it acts as the command signal. The position encoder provides the feedback signal for this block. This means that the velocity and position amplifiers are actually a closed-loop system within a closed-loop system. The gain for e

8、ach of these amplifiers must be tuned so that the system has the best torque response and smooth acceleration and deceleration.FIGURE 11-81 An AC servo drive amplifier specifically designed to operate with an AC trapezoidal brushless servomotor.The feedback mechanism is generally a brushless DC tach generator, or an AC generator. Each of these feedback mechanisms provides smooth feedback voltages. If an encoder is used, its binary (digital) signal must be converted to an analog signal through a D/A converter or a frequency-to-analog F/A type converter if the signal is produced as a frequency.

展开阅读全文
温馨提示:
1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 装配图网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

copyright@ 2023-2025  zhuangpeitu.com 装配图网版权所有   联系电话:18123376007

备案号:ICP2024067431-1 川公网安备51140202000466号


本站为文档C2C交易模式,即用户上传的文档直接被用户下载,本站只是中间服务平台,本站所有文档下载所得的收益归上传人(含作者)所有。装配图网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。若文档所含内容侵犯了您的版权或隐私,请立即通知装配图网,我们立即给予删除!